On 25/10/2016 09:04:51, Youssef BENGELLOUN - ZAHR <ybzahr@prodware.fr> wrote:
Dear Mike,
I’m not spamming, I’m just opening a thread for each different subject. I’m trying to improve the software by giving as much feedback as I can :-)
Actually, I was asking if it’s possible to achieve the same results as observium already provides for FANs / PSUs i.e. displaying modules’ state :
This is for a Brocade CER-RT router :
==> NOTICE here that FAN status is missing for this particular device. Nothing about modules’ state.
This is for an Brocade MLXe-4 router :
==> NOTICE here that FAN status is missing for this particular device. Nothing about modules’ state.
This is for an SRX550 firewall :
==> All good here. Nothing about modules’ state.
This is for an SRX5600 firewall :
==> All good here. Nothing about modules’ state.
If you look at the output from the following commands on the devices themselves, you get the information of the modules’ state. Highlighted in yellow is what I’m trying to find/display.
- This is for an MLXe :
show module
Module Status Ports Starting MAC
M1 (left ):BR-MLX-MR2-X Management Module Standby(Ready State)
M2 (right):BR-MLX-MR2-X Management Module Active
F1: NI-X-HSF Switch Fabric Module Active
F2: NI-X-HSF Switch Fabric Module Active
F3:
S1: BR-MLX-10Gx4-X 4-port 10GbE Module CARD_STATE_UP 4 0024.38a4.fb00
S2: BR-MLX-10Gx4-X 4-port 10GbE Module CARD_STATE_UP 4 0024.38a4.fb30
S3: BR-MLX-1GFx24-X 24-port 1GbE SFP Module CARD_STATE_UP 24 0024.38a4.fb60
S4:
sh chassis
*** MLXe 4-slot Chassis ***
---POWERS ---
Power 1: (23-0000129-02 BMG2J10G0KG - AC 1800W): Installed (OK)
Power 2: (23-0000129-02 BMG2J09G08L - AC 1800W): Installed (OK)
Power 3: not present
Power 4: not present
Total power budget for chassis = 3600 W
Total power used by system core = 450 W
Total power used by LPs = 640 W
Total power available = 2510 W
Slot Power-On Priority and Power Usage:
Slot1 pri=1 module type=BR-MLX-10Gx4-X 4-port 10GbE Module power usage=240W
Slot2 pri=1 module type=BR-MLX-10Gx4-X 4-port 10GbE Module power usage=240W
Slot3 pri=1 module type=BR-MLX-1GFx24-X 24-port 1GbE SFP Module power usage=160W
--- FANS ---
Back fan A-1: Status = OK, Speed = LOW (50%)
Back fan A-2: Status = OK, Speed = LOW (50%)
Back fan B-1: Status = OK, Speed = LOW (50%)
Back fan B-2: Status = OK, Speed = LOW (50%)
Back fan C-1: Status = OK, Speed = LOW (50%)
Back fan C-2: Status = OK, Speed = LOW (50%)
Back fan D-1: Status = OK, Speed = LOW (50%)
Back fan D-2: Status = OK, Speed = LOW (50%)
--- TEMPERATURE READINGS ---
Active Mgmt Module: 38.500C 53.750C
Standby Mgmt Module: 36.250C 49.625C
SFM1: FE1:44.500C
SFM2: FE1:45.500C
SFM3: not present
LP1 Sensor1: 42.500C
LP1 Sensor2: 44.875C
LP1 Sensor3: UNUSED
LP1 Sensor4: 42.0C
LP1 Sensor5: 45.750C
LP1 Sensor6: UNUSED
LP2 Sensor1: 48.0C
LP2 Sensor2: 53.125C
LP2 Sensor3: UNUSED
LP2 Sensor4: 46.500C
LP2 Sensor5: 52.875C
LP2 Sensor6: UNUSED
LP3 Sensor1: 44.0C
LP3 Sensor2: 40.125C
LP3 Sensor3: UNUSED
Fans are in auto mode (current speed is LOW (50%)). Temperature monitoring poll period is 60 seconds.
This is for an SRX5600 :
y.bengelloun@fw01-par01> show chassis craft-interface
node0:
--------------------------------------------------------------------------
Front Panel System LEDs:
Routing Engine 0 1
--------------------------
OK * .
Fail . .
Master * .
Front Panel Alarm Indicators:
-----------------------------
Red LED .
Yellow LED .
Major relay .
Minor relay .
Front Panel FPC LEDs:
FPC 0 1 2 3 4 5
------------------------------
Red . . . . . .
Green * . . . . *
CB LEDs:
CB 0 1
--------------
Amber . .
Green * .
PS LEDs:
PS 0 1 2 3
--------------------
Red . . . .
Green * * . .
Fan Tray LEDs:
FT 0
----------
Red .
Green *
show chassis fpc
node0:
--------------------------------------------------------------------------
Temp CPU Utilization (%) Memory Utilization (%)
Slot State (C) Total Interrupt DRAM (MB) Heap Buffer
0 Online 36 6 0 1024 11 42
1 Empty
2 Empty
3 Empty
4 Empty
5 Online 34 22 0 1024 9 25
y.bengelloun@fw01-par01> show chassis fpc detail
node0:
--------------------------------------------------------------------------
Slot 0 information:
State Online
Temperature 35
Total CPU DRAM 1024 MB
Total RLDRAM 128 MB
Total DDR DRAM 2048 MB
Start time: 2016-01-10 05:12:39 CET
Uptime: 289 days, 3 hours, 18 minutes, 14 seconds
Max Power Consumption 250 Watts
Slot 5 information:
State Online
Temperature 33
Total CPU DRAM 1024 MB
Total RLDRAM 259 MB
Total DDR DRAM 4864 MB
Start time: 2016-01-10 05:06:39 CET
Uptime: 289 days, 3 hours, 24 minutes, 14 seconds
Max Power Consumption 585 Watts
In SRX philosophy, each FPC (or line-card) holds multiple PICs on it :
y.bengelloun@fw01-par01> show chassis fpc pic-status
node0:
--------------------------------------------------------------------------
Slot 0 Online SRX5k FIOC
PIC 0 Online 16x 1GE TX
Slot 5 Online SRX5k SPC II
PIC 0 Online SPU Cp
PIC 1 Online SPU Flow
PIC 2 Online SPU Flow
PIC 3 Online SPU Flow
Please find attached requested outputs from both devices : MLXe-4 and SRX5600.
I have also attached additional outputs from other models from the same family : CER-RT and SRX550.
I hope this helps.
Best regards.
From: observium <observium-bounces@observium.org> on behalf of Mike Stupalov <mike@observium.org>
Reply-To: "mike@observium.org" <mike@observium.org>, Observium Network Observation System <observium@observium.org>
Date: mardi 25 octobre 2016 09:12
To: Observium Network Observation System <observium@observium.org>
Subject: Re: [Observium] Missing status Indicators for slots/modules
And pls do not spam ML with multiple same questions....
Youssef BENGELLOUN - ZAHR - Consultant Expert
Prodware France
T : +33 979 999 000 - F : +33 988 814 001 - ybzahr@prodware.fr
Web : prodware.fr 
