2015-11-18 6:36 GMT-03:00 Gediminas Karčmarinas <gediminas@kava.lt>:

All device have response time exelent,but when it take port info then it slow.

Question : Howto disbale ports up/down/speed taken info ?
On 2015-11-18 11:21, Markus Klock wrote:
have you tried increasing the amount of pollers? 40 might be kind of few for 1300 devices if you have a lot of them are slow.

/Markus

2015-11-17 21:37 GMT+01:00 Alex Povolotsky <tarkhil@over.ru>:

I've started perl-based poller with much better performance, but not
working on it for long time now, more pressing matters persists.

https://github.com/tarkhil/observium-poller

feel free to improve

On 17.11.2015 23:24, Gediminas Karčmarinas wrote:
> so what do is will be 2000 device and more ? What solution for
> poller.php to run faster ? I already disable all modules but still is
> take to long
>
> On 2015.11.17 22:12, Alex Povolotsky wrote:
>> poller.php is ugly, it uses external utilities and just cannot run more
>> or less fast.
>>
>> On 17.11.2015 17:22, Gediminas Karčmarinas wrote:
>>> Hello,
>>> Maybe is some way to get better performance with poller.php ?
>>> poller-wrapper.py(24406): /opt/observium/poller-wrapper.py: polled 1310
>>> devices in 270 seconds with 40 workers
>>>
>>> I already disable in what I don't need in
>>> '/opt/observium/includes/defaults.inc.php'
>>> $config['mibs']['SNMPv2-MIB'] = 1;
>>> $config['mibs']['IF-MIB'] = 1;
>>> $config['mibs']['OSPF-MIB'] = 0;
>>> $config['mibs']['EIGRP-MIB'] = 0;
>>> $config['mibs']['CISCO-MAC-ACCOUNTING-MIB'] = 0;
>>> $config['mibs']['JUNIPER-MAC-MIB'] = 0;
>>> $config['mibs']['IP-MIB'] = 1;
>>> $config['mibs']['IPV6-MIB'] = 0;
>>> $config['mibs']['CISCO-IETF-IP-MIB'] = 0;
>>> $config['mibs']['BGP4-V2-MIB-JUNIPER'] = 0;
>>> $config['mibs']['FORCE10-BGP4-V2-MIB'] = 0;
>>> $config['mibs']['BGP4-MIB'] = 0;
>>> $config['mibs']['CISCO-BGP4-MIB'] = 0;
>>> $config['mibs']['CISCO-CEF-MIB'] = 0;
>>> $config['mibs']['ENTITY-MIB'] = 0;
>>> $config['mibs']['CISCO-ENTITY-SENSOR-MIB'] = 0;
>>> $config['mibs']['ENTITY-SENSOR-MIB'] = 0;
>>> $config['mibs']['CISCO-IETF-PW-MPLS-MIB'] = 0;
>>> $config['mibs']['CISCO-RTTMON-MIB'] = 0;
>>> $config['mibs']['MPLS-L3VPN-STD-MIB'] = 0;
>>> $config['mibs']['MPLS-VPN-MIB'] = 0;
>>> $config['mibs']['FOUNDRY-SN-SWITCH-GROUP-MIB'] = 0;
>>> $config['mibs']['LLDP-MIB'] = 0;
>>> $config['mibs']['BRIDGE-MIB'] = 0;
>>> $config['mibs']['HOST-RESOURCES-MIB'] = 0;
>>> $config['mibs']['Juniper-UNI-ATM-MIB'] = 0;
>>> $config['mibs']['UCD-SNMP-MIB'] = 0;
>>> $config['mibs']['UCD-DISKIO-MIB'] = 0;
>>> $config['mibs']['Q-BRIDGE-MIB'] = 0;
>>> $config['mibs']['VMWARE-VMINFO-MIB'] = 0;
>>> $config['mibs']['EtherLike-MIB'] = 0;
>>>
>>> $config['poller_modules']['unix-agent'] = 0;
>>> $config['poller_modules']['ipmi'] = 0;
>>> $config['poller_modules']['sensors'] = 1;
>>> $config['poller_modules']['status'] = 1;
>>> $config['poller_modules']['processors'] = 1;
>>> $config['poller_modules']['mempools'] = 1;
>>> $config['poller_modules']['storage'] = 1;
>>> $config['poller_modules']['netstats'] = 1;
>>> $config['poller_modules']['hr-mib'] = 0;
>>> $config['poller_modules']['ucd-mib'] = 0;
>>> $config['poller_modules']['ipSystemStats'] = 1;
>>> $config['poller_modules']['ports'] = 1;
>>> $config['poller_modules']['bgp-peers'] = 0;
>>> $config['poller_modules']['junose-atm-vp'] = 0;
>>> $config['poller_modules']['toner'] = 0;
>>> $config['poller_modules']['ucd-diskio'] = 0;
>>> $config['poller_modules']['wifi'] = 0;
>>> $config['poller_modules']['ospf'] = 0;
>>> $config['poller_modules']['cisco-ipsec-flow-monitor'] = 0;
>>> $config['poller_modules']['cisco-remote-access-monitor'] = 0;
>>> $config['poller_modules']['cisco-cef'] = 0;
>>> $config['poller_modules']['cisco-sla'] = 0;
>>> $config['poller_modules']['mac-accounting'] = 0;
>>> $config['poller_modules']['arista-software-ip-forwarding']= 0;
>>> $config['poller_modules']['cipsec-tunnels'] = 0;
>>> $config['poller_modules']['loadbalancer'] = 0;
>>> $config['poller_modules']['cisco-cbqos'] = 0;
>>> $config['poller_modules']['cisco-eigrp'] = 0;
>>> $config['poller_modules']['netscaler-vsvr'] = 0;
>>> $config['poller_modules']['aruba-controller'] = 0;
>>> $config['poller_modules']['entity-physical'] = 0;
>>> $config['poller_modules']['applications'] = 0;
>>> $config['poller_modules']['fdb-table'] = 1;
>>> $config['poller_modules']['graphs'] = 1;
>>> $config['poller_modules']['cisco-vpdn'] = 0;
>>> $config['poller_modules']['wmi'] = 0;
>>>
>>>
>>>
>>> Hardware : SSD INTEL
>>> MEM : 14GB
>>> CPU : Intel(R) Xeon(R) CPU E3-1270 v3 @ 3.50GHz
>>>
>>>
>>> _______________________________________________
>>> observium mailing list
>>> observium@observium.org
>>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
>>>
>> _______________________________________________
>> observium mailing list
>> observium@observium.org
>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
>
> _______________________________________________
> observium mailing list
> observium@observium.org
> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

There was a nice wrapper published by Job Snijders on the list, and works really well on our end.

Ref:

http://postman.memetic.org/pipermail/observium/2012-November/001303.html

Regards,

--

Ciro Iriarte
http://iriarte.it
--