Jupi, I found the latest version firmware from June which solves the problem ☺ THX
##### Module Start: sensors #####
+----------+-----------+------+--------+-------+-------+---------------------+ | Descr | Class | Type | Origin | Value | Event | Last Changed | +----------+-----------+------+--------+-------+-------+---------------------+ | Source A | voltage | apc | snmp | 228V | ok | 2018-08-31 13:32:00 | | Source B | voltage | apc | snmp | 240V | ok | 2018-08-31 13:32:00 | | Output | voltage | apc | snmp | 228V | ok | 2018-08-31 13:32:00 | | Source A | frequency | apc | snmp | 50Hz | ok | 2018-08-31 13:20:42 | | Source B | frequency | apc | snmp | 50Hz | ok | 2018-08-31 13:20:42 | | Output | frequency | apc | snmp | 50Hz | ok | 2018-08-31 13:20:42 | | Output | power | apc | snmp | 205W | ok | 2018-08-31 13:32:52 | | Output | current | apc | snmp | 0.9A | ok | 2018-04-06 11:07:29 |
Pozdrawiam Jacek Dąbrowski
From: Mike Stupalov mike@stupalov.ru On Behalf Of Mike Stupalov Sent: Friday, August 31, 2018 3:01 PM To: Dąbrowski Jacek Jacek.Dabrowski@selgros.pl Cc: observium@observium.org Subject: Re: [Observium] APC ATS - continued
- try switch to SNMP v2c (I sure your device support it) - write TAC to vendor - downgrade firmware :)
I tested on another ATS device and not see issue.
Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl wrote:
hmm I'm afraid you can be right, but unfortunately I'm using the latest version available.
Pozdrawiam Jacek Dąbrowski
From: Mike Stupalov mike@stupalov.rumailto:mike@stupalov.ru On Behalf Of Mike Stupalov Sent: Friday, August 31, 2018 2:27 PM To: Dąbrowski Jacek Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl Cc: observium@observium.orgmailto:observium@observium.org Subject: Re: [Observium] APC ATS - continued
This is firmware/hardware issue, try to upgrade device firmware.
SNMPv2-MIB does not matter here, since in poller all oids requested by numeric oids.
When walked (snmpwalk) table - value returned, when try to snmpget specific oid - return error.
Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl wrote:
Done, I see all the time SNMPv2-MIB no PowerNet-MIB in poller. SNMPv2-MIB its wrong mib for this device.
Pozdrawiam Jacek Dąbrowski
From: Mike Stupalov mike@stupalov.rumailto:mike@stupalov.ru On Behalf Of Mike Stupalov Sent: Friday, August 31, 2018 1:36 PM To: Observium observium@observium.orgmailto:observium@observium.org; Dąbrowski Jacek Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl Subject: Re: [Observium] APC ATS - continued
Hi,
please attach output for poller debug:
./poller.php -d -m sensors -h <device>
Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl 31 August 2018 at 12:21 Hello Adam,
My Observium now: Observium
18.8.9403 (27th August 2018)
But in GUI nothing has changed, new debug in the attachments.
[cid:image001.jpg@01D44140.5DD3A1D0]
Pozdrawiam Jacek Dąbrowski
From: observium observium-bounces@observium.orgmailto:observium-bounces@observium.org On Behalf Of Adam Armstrong Sent: Wednesday, August 29, 2018 8:16 PM To: observium@observium.orgmailto:observium@observium.org Subject: Re: [Observium] APC ATS - continued
I checked locally on an ATS system before I noticed the version was old, and those OIDs used in the poller are correct, so it is probably a bug that was fixed.
adam.
_______________________________________________ observium mailing list observium@observium.orgmailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium Adam Armstrongmailto:adama@memetic.org 29 August 2018 at 21:16 I checked locally on an ATS system before I noticed the version was old, and those OIDs used in the poller are correct, so it is probably a bug that was fixed.
adam. _______________________________________________ observium mailing list observium@observium.orgmailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl 29 August 2018 at 21:02 OK, I will check soon in the new version.
Pozdrawiam Jacek Dąbrowski
From: observium observium-bounces@observium.orgmailto:observium-bounces@observium.org On Behalf Of Adam Armstrong Sent: Wednesday, August 29, 2018 6:35 PM To: observium@observium.orgmailto:observium@observium.org Subject: Re: [Observium] APC ATS - continued
Last Changed Rev: 9073 Last Changed Date: 2018-03-02 23:37:46 +0100 (Fri, 02 Mar 2018)
Please don't report issues with ancient versions.
Thanks, adam.
_______________________________________________ observium mailing list observium@observium.orgmailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium Adam Armstrongmailto:adama@memetic.org 29 August 2018 at 19:34 Last Changed Rev: 9073 Last Changed Date: 2018-03-02 23:37:46 +0100 (Fri, 02 Mar 2018)
Please don't report issues with ancient versions.
Thanks, adam. _______________________________________________ observium mailing list observium@observium.orgmailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium Jacek.Dabrowski@selgros.plmailto:Jacek.Dabrowski@selgros.pl 29 August 2018 at 19:03 Hello,
I am coming back with the topic of APC ATS, maybe someone will help. The subject of the correct voltage after the discovery, the value is correct, when pooler finish working the value disappears. As I noticed during the discovery, is viewed source in PowerNet-MIB in debug mode , the pooler process in debug is searched in SNMPv2-MIB !!! Is it some bug ?
Details in the attachments.
Regards Jacek Dąbrowski
_______________________________________________ observium mailing list observium@observium.orgmailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
-- Mike Stupalov Observium Limited, http://observium.org
-- Mike Stupalov Observium Limited, http://observium.org
-- Mike Stupalov Observium Limited, http://observium.org
