Hi there, We monitor APC pdu's here and have set up the following metrics:
41 PDU SENSOR ALARM notification of a warning/alert/down event on sensor
sensor_event eq warning sensor_event eq alert sensor_event eq down
type match power
*
This then picks up on all the sensors on that device: power banks 1 and 2 , power supply and voltage.
Then if you go into the the node, click settings and then "sensor" you can manually set the min/ max for each one . once this hits it will alarm!
Hope this helps
ndex MIB Type Class Descr Current Min Max Custom Limits Reset Limits Alerts rPDULoadStatusLoad.1 apc current Bank Total 8.1A xx rPDULoadStatusLoad.2 apc current Bank 1 6.2A xx rPDULoadStatusLoad.3 apc current Bank 2 1.8A rPDUIdentDevicePowerWatts.0 apc power Input 1.86kW rPDUIdentDeviceLinetoLineVoltage.0 apc voltage Line-to-Line 230V rPDUPowerSupply1Status.0 powernet-rpdusupply1-state state Power Supply 1 powerSupplyOneOk
Brett Jones 2nd/3rd line support engineer
Tel: 01202 612000 Fax: 01202 612111 W:www.voip-unlimited.net E:brett.jones@voip-unlimited.net E:support@voip-unlimited.net
Registered Office: Co Carter & Coley, 3 Durrant Road, Bournemouth, Dorset BH2 6NE Registered in England No: 05225497
-----Original Message----- From: observium [mailto:observium-bounces@observium.org] On Behalf Of observium-request@observium.org Sent: 14 November 2014 16:38 To: observium@observium.org Subject: observium Digest, Vol 52, Issue 51
Send observium mailing list submissions to observium@observium.org
To subscribe or unsubscribe via the World Wide Web, visit http://postman.memetic.org/cgi-bin/mailman/listinfo/observium or, via email, send a message with subject or body 'help' to observium-request@observium.org
You can reach the person managing the list at observium-owner@observium.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of observium digest..."
Today's Topics:
1. Power Statistics (Josh Hopper)
----------------------------------------------------------------------
Message: 1 Date: Fri, 14 Nov 2014 11:37:25 -0500 From: Josh Hopper joshhopper@protectplus.com To: Observium Network Observation System observium@observium.org Subject: [Observium] Power Statistics Message-ID: 5BBFC1D5E54E9341821836E23038ADEC04DC527A21E1@SVR-EXCHANGE Content-Type: text/plain; charset="us-ascii"
How do I make an alert for power where it alerts me if my amperage (current) is over 80%. For me that would be about 11 AMPs on my UPS.
-- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image001.jpg@01CFFFFF.5CF8B420] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160 | Cell: 828-855-7565
Protect Plus Air Holdings, LLC and Affiliates, Protect Plus, LLC and Affiliates, Imagine One Resources, LLC and Affiliates, Protect Plus Surfaces, LLC and Affiliates Confidentiality Notice: This e-mail is intended only for the addressee named above. It contains information that is privileged, confidential or otherwise protected from use and disclosure. If you are not the intended recipient, you are hereby notified that any review, disclosure, copying, or dissemination of this transmission, or taking of any action in reliance on its contents, or other use is strictly prohibited. If you have received this transmission in error, please reply to the sender listed above immediately and permanently delete this message from your inbox. Thank you for your cooperation.