Re: [Observium] Clavister device as new OS

10 Dec 2015


      Ok, I didn't know that.Then I'd like to submit a feature request to add support for this OS :)
From: adama@memetic.org
To: observium@observium.org
Date: Thu, 10 Dec 2015 00:39:55 +0000
Subject: Re: [Observium] Clavister device as new OS
Your mistake is thinking that
MIBs are useful :)
What did you think they'd be
used for? They aren't drivers, there's no standardised way for them to tell
an nms what they are describing.
Adding support for new MIBs
involves writing code which makes use of the MIBs to make sense of the
device's SNMP output.
Adam.
Sent with AquaMail for Android
http://www.aqua-mail.com
On
10 December 2015 00:35:48 Gregory Storme gregory_storme@hotmail.com
wrote:
Hi,
I'm trying to add Clavister cOS as a
supported OS, but without success.What I've
done:
-
Edit includes/definitions/os.inc.php:$os =
"clavister";$config['os'][$os]['vendor']      
         =
"Clavister";$config['os'][$os]['text']      
           =
"Clavister cOS";$config['os'][$os]['type']      
           =
"network";$config['os'][$os]['icon']        
         =
"clavister";$config['os'][$os]['graphs'][]      
       =
"device_bits";$config['os'][$os]['graphs'][]    
         =
"device_processor";$config['os'][$os]['graphs'][]    
         =
"device_mempool";$config['os'][$os]['sysObjectID'][]  
      =
".1.3.6.1.4.1.5089.1";$config['os'][$os]['sysDescr'][]  
         =
"/^Clavister/";$config['os'][$os]['mibs'][]      
         =
"CLAVISTER-MIB";$config['os'][$os]['mibs'][]    
           =
"CLAVISTER-SMI-MIB";
-
create includes/discovery/os/clavister.inc.php:<?php 
if (strstr($sysObjectId, ".1.3.6.1.4.1.5089.1")) { $os = "clavister";
}  else if (preg_match("/^Clavister/", $sysDescr)) { $os =
"clavister"; }
- created the CLAVISTER-MIB & CLAVISTER-SMI-MIB (downloaded from the vendor
website) under the mibs folder
When I add such a device and run the discovery
& poller, it seems as the Clavister MIBs are not
used.The OS type is
detected though?
#####  devicename
[338]  #####
 o OS      
            clavister o Last
poll duration   0.42 seconds o Last Polled  
       2015-12-10 01:28:30 o SNMP
Version         v2c o Device status
       Device is reachable by PING (0.36ms) and SNMP
(7.20ms) o Modules Excluded     ipmi,
junose-atm-vp, cisco-ipsec-flow-monitor, cisco-remote-access-monitor,
cisco-cef,
arista-software-ip-forwarding,cipsec-tunnels, cisco-cbqos, cisco-eigrp,
netscaler-vsvr, aruba-controller o Disabled Globally  
 unix-agent, cisco-vpdn, wmi o Modules Enabled  
   system, os, sensors, status, processors, mempools, storage,
netstats, hr-mib, ucd-mib, ipSystemStats, ports,
bgp-peers,             
          toner,ucd-diskio, wifi, p2p-radios,
ospf, sla, mac-accounting, loadbalancer, entity-physical, applications,
fdb-table,
graphs,oids
#####  Module Start: system
 #####
 o Uptime      
        8 days, 1h 57m 55s o
sysObjectID        
 .1.3.6.1.4.1.5089.1 o snmpEngineID o
sysDescr             Clavister cOS Core
10.21.02.01-25325 o sysName        
     n/a o Location      
      N/A o Module time      
   0.0578s
#####  Module Start: os
 #####
 o OS Poller
Generic...
What am I doing
wrong?
_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium