I’m not spamming, I’m just opening a thread for each different subject. I’m trying to improve the software by giving as much feedback as I can :-)

Actually, I was asking if it’s possible to achieve the same results as observium already provides for FANs / PSUs i.e. displaying modules’ state :

This is for a Brocade CER-RT router :

==> NOTICE here that FAN status is missing for this particular device. Nothing about modules’ state.

This is for an Brocade MLXe-4 router :

==> NOTICE here that FAN status is missing for this particular device. Nothing about modules’ state.

This is for an SRX550 firewall :

==> All good here. Nothing about modules’ state.

This is for an SRX5600 firewall :

==> All good here. Nothing about modules’ state.

If you look at the output from the following commands on the devices themselves, you get the information of the modules’ state. Highlighted in yellow is what I’m trying to find/display.

- This is for an MLXe :

show module

Module Status Ports Starting MAC

M1 (left ):BR-MLX-MR2-X Management Module Standby(Ready State)

M2 (right):BR-MLX-MR2-X Management Module Active

F1: NI-X-HSF Switch Fabric Module Active

F2: NI-X-HSF Switch Fabric Module Active

F3:

S1: BR-MLX-10Gx4-X 4-port 10GbE Module CARD_STATE_UP 4 0024.38a4.fb00

S2: BR-MLX-10Gx4-X 4-port 10GbE Module CARD_STATE_UP 4 0024.38a4.fb30

S3: BR-MLX-1GFx24-X 24-port 1GbE SFP Module CARD_STATE_UP 24 0024.38a4.fb60

S4:

sh chassis

*** MLXe 4-slot Chassis ***

---POWERS ---

Power 1: (23-0000129-02 BMG2J10G0KG - AC 1800W): Installed (OK)

Power 2: (23-0000129-02 BMG2J09G08L - AC 1800W): Installed (OK)

Power 3: not present

Power 4: not present

Total power budget for chassis = 3600 W

Total power used by system core = 450 W

Total power used by LPs = 640 W

Total power available = 2510 W

Slot Power-On Priority and Power Usage:

Slot1 pri=1 module type=BR-MLX-10Gx4-X 4-port 10GbE Module power usage=240W

Slot2 pri=1 module type=BR-MLX-10Gx4-X 4-port 10GbE Module power usage=240W

Slot3 pri=1 module type=BR-MLX-1GFx24-X 24-port 1GbE SFP Module power usage=160W

--- FANS ---

Back fan A-1: Status = OK, Speed = LOW (50%)

Back fan A-2: Status = OK, Speed = LOW (50%)

Back fan B-1: Status = OK, Speed = LOW (50%)

Back fan B-2: Status = OK, Speed = LOW (50%)

Back fan C-1: Status = OK, Speed = LOW (50%)

Back fan C-2: Status = OK, Speed = LOW (50%)

Back fan D-1: Status = OK, Speed = LOW (50%)

Back fan D-2: Status = OK, Speed = LOW (50%)

--- TEMPERATURE READINGS ---

Active Mgmt Module: 38.500C 53.750C

Standby Mgmt Module: 36.250C 49.625C

SFM1: FE1:44.500C

SFM2: FE1:45.500C

SFM3: not present

LP1 Sensor1: 42.500C

LP1 Sensor2: 44.875C

LP1 Sensor3: UNUSED

LP1 Sensor4: 42.0C

LP1 Sensor5: 45.750C

LP1 Sensor6: UNUSED

LP2 Sensor1: 48.0C

LP2 Sensor2: 53.125C

LP2 Sensor3: UNUSED

LP2 Sensor4: 46.500C

LP2 Sensor5: 52.875C

LP2 Sensor6: UNUSED

LP3 Sensor1: 44.0C

LP3 Sensor2: 40.125C

LP3 Sensor3: UNUSED

Fans are in auto mode (current speed is LOW (50%)). Temperature monitoring poll period is 60 seconds.

This is for an SRX5600 :

y.bengelloun@fw01-par01> show chassis craft-interface

node0:

--------------------------------------------------------------------------

Front Panel System LEDs:

Routing Engine 0 1

--------------------------

OK * .

Fail . .

Master * .

Front Panel Alarm Indicators:

-----------------------------

Red LED .

Yellow LED .

Major relay .

Minor relay .

Front Panel FPC LEDs:

FPC 0 1 2 3 4 5

------------------------------

Red . . . . . .

Green * . . . . *

CB LEDs:

CB 0 1

--------------

Amber . .

Green * .

PS LEDs:

PS 0 1 2 3

--------------------

Red . . . .

Green * * . .

Fan Tray LEDs:

FT 0

----------

Red .

Green *

show chassis fpc

node0:

--------------------------------------------------------------------------

Temp CPU Utilization (%) Memory Utilization (%)

Slot State (C) Total Interrupt DRAM (MB) Heap Buffer

0 Online 36 6 0 1024 11 42

1 Empty

2 Empty

3 Empty

4 Empty

5 Online 34 22 0 1024 9 25

y.bengelloun@fw01-par01> show chassis fpc detail

node0:

--------------------------------------------------------------------------

Slot 0 information:

State Online

Temperature 35

Total CPU DRAM 1024 MB

Total RLDRAM 128 MB

Total DDR DRAM 2048 MB

Start time: 2016-01-10 05:12:39 CET

Uptime: 289 days, 3 hours, 18 minutes, 14 seconds

Max Power Consumption 250 Watts

Slot 5 information:

State Online

Temperature 33

Total CPU DRAM 1024 MB

Total RLDRAM 259 MB

Total DDR DRAM 4864 MB

Start time: 2016-01-10 05:06:39 CET

Uptime: 289 days, 3 hours, 24 minutes, 14 seconds

Max Power Consumption 585 Watts

In SRX philosophy, each FPC (or line-card) holds multiple PICs on it :

y.bengelloun@fw01-par01> show chassis fpc pic-status

node0:

--------------------------------------------------------------------------

Slot 0 Online SRX5k FIOC

PIC 0 Online 16x 1GE TX

Slot 5 Online SRX5k SPC II

PIC 0 Online SPU Cp

PIC 1 Online SPU Flow

PIC 2 Online SPU Flow

PIC 3 Online SPU Flow

Please find attached requested outputs from both devices : MLXe-4 and SRX5600.

I have also attached additional outputs from other models from the same family : CER-RT and SRX550.

From: observium <observium-bounces@observium.org> on behalf of Mike Stupalov <mike@observium.org>
Reply-To: "mike@observium.org" <mike@observium.org>, Observium Network Observation System <observium@observium.org>
Date: mardi 25 octobre 2016 09:12
To: Observium Network Observation System <observium@observium.org>
Subject: Re: [Observium] Missing status Indicators for slots/modules

And pls do not spam ML with multiple same questions....

On Tue, Oct 25, 2016 at 10:11 AM, Mike Stupalov <mike@observium.org> wrote:

Hi,

not fully understand your trouble.

Status indicators complete not exist (or removed from some time)?

Or exist but not polled?

If second, try increase snmp timeout for device(s) to 3-5sec.

For more relevant info, show screenshots and attach debug output:

./discovery.php -d -m sensors -h <device>
./poller.php -d -m sensors -h <device>

On Tue, Oct 25, 2016 at 9:49 AM, Youssef BENGELLOUN - ZAHR <ybzahr@prodware.fr> wrote:

Dear Community,

I noticed that for some networking gear (for example : Brocade MLXe / Juniper SRX), status indicators for the modules (i.e. OK / NOK / shutdown / etc.) are missing.

For instance, Temperature / CPU / mem usage are polled correctly but not the status of the module itself.

So I’m asking the community if this is normal behavior ? If this information should be considered relevant ?

Thank you.

Youssef BENGELLOUN - ZAHR - Consultant Expert
Prodware France
T : +33 979 999 000 - F : +33 988 814 001 - ybzahr@prodware.fr

Web : prodware.fr

_______________________________________________
observium mailing list
observium@observium.org
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

--

Mike Stupalov
http://observium.org/

Mike Stupalov
http://observium.org/