Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in addition to some J-series units that we'll probably replace with another pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as usual. Devices get detected properly, node0 & node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state inserted SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta` ='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09 </paste>
My first impression is that it's the MIB incorrectly polling the device, Can anybody confirm?
Cheers,
JG
Further up the debug output you can see the data returned from the switch. You're looking for ifHCInOctets && ifHCOutOctets.
If the SRX is fucking those up, which I can totally believe for a cluster, you need to talk to Pooniper about it.
adam.
On Fri, 01 Feb 2013 14:09:32 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in
addition to some J-series units that we'll probably replace with another
pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as
usual. Devices get detected properly, node0 & node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the
interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller
is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state
inserted
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta`
='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device,
Can anybody confirm?
Cheers,
JG
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
Hey mate,
Do you mean 'ifInOctets' & 'ifOutOctets' ? If you do then i'm poo-ie, because the return is 0.
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',
ifInOctets.1 = 0 ifInOctets.2 = 1928549980 ifInOctets.3 = 0 ifInOctets.4 = 0 ifInOctets.6 = 16751052 ifInOctets.7 = 0 ifInOctets.8 = 0 ifInOctets.9 = 0 ifInOctets.10 = 0 ifInOctets.11 = 0 ifInOctets.12 = 0 ifInOctets.13 = 0 ifInOctets.14 = 1895484058 ifInOctets.15 = 0 ifInOctets.16 = 0 ifInOctets.21 = 0 ifInOctets.22 = 16751052 ifInOctets.501 = 0 ifInOctets.502 = 0 ifInOctets.503 = 0 ifInOctets.504 = 0 ifInOctets.505 = 0 ifInOctets.506 = 0 ifInOctets.507 = 0 ifInOctets.508 = 0 ifInOctets.509 = 0 ifInOctets.511 = 0 ifInOctets.512 = 0 ifInOctets.513 = 0 ifInOctets.514 = 0 ifInOctets.516 = 0 ifInOctets.517 = 0 ifInOctets.518 = 0 ifInOctets.519 = 0 ifInOctets.521 = 0 ifInOctets.522 = 0 ifInOctets.524 = 0
Jacob Gardiner mailto:jacob@jacobgardiner.com 1 February 2013 2:09 PM Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in addition to some J-series units that we'll probably replace with another pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as usual. Devices get detected properly, node0 & node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state inserted SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta` ='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device, Can anybody confirm?
Cheers,
JG
Adam Armstrong mailto:adama@memetic.org 1 February 2013 2:06 PM Further up the debug output you can see the data returned from the switch. You're looking for ifHCInOctets&& ifHCOutOctets.
If the SRX is fucking those up, which I can totally believe for a cluster, you need to talk to Pooniper about it.
adam.
On Fri, 01 Feb 2013 14:09:32 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in
addition to some J-series units that we'll probably replace with another
pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as
usual. Devices get detected properly, node0& node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the
interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller
is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state
inserted
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta`
='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device,
Can anybody confirm?
Cheers,
JG
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
Did you mistakenly add the device as SNMPv1?
adam.
On Fri, 01 Feb 2013 15:08:02 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hey mate,
Do you mean 'ifInOctets' & 'ifOutOctets' ? If you do then i'm poo-ie, because the return is 0.
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',
ifInOctets.1 = 0 ifInOctets.2 = 1928549980 ifInOctets.3 = 0 ifInOctets.4 = 0 ifInOctets.6 = 16751052 ifInOctets.7 = 0 ifInOctets.8 = 0 ifInOctets.9 = 0 ifInOctets.10 = 0 ifInOctets.11 = 0 ifInOctets.12 = 0 ifInOctets.13 = 0 ifInOctets.14 = 1895484058 ifInOctets.15 = 0 ifInOctets.16 = 0 ifInOctets.21 = 0 ifInOctets.22 = 16751052 ifInOctets.501 = 0 ifInOctets.502 = 0 ifInOctets.503 = 0 ifInOctets.504 = 0 ifInOctets.505 = 0 ifInOctets.506 = 0 ifInOctets.507 = 0 ifInOctets.508 = 0 ifInOctets.509 = 0 ifInOctets.511 = 0 ifInOctets.512 = 0 ifInOctets.513 = 0 ifInOctets.514 = 0 ifInOctets.516 = 0 ifInOctets.517 = 0 ifInOctets.518 = 0 ifInOctets.519 = 0 ifInOctets.521 = 0 ifInOctets.522 = 0 ifInOctets.524 = 0
Jacob Gardiner mailto:jacob@jacobgardiner.com 1 February 2013 2:09 PM Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in addition to some J-series units that we'll probably replace with another pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as usual. Devices get detected properly, node0 & node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state inserted SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta` ='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device, Can anybody confirm?
Cheers,
JG
Adam Armstrong mailto:adama@memetic.org 1 February 2013 2:06 PM Further up the debug output you can see the data returned from the switch. You're looking for ifHCInOctets&& ifHCOutOctets.
If the SRX is fucking those up, which I can totally believe for a cluster, you need to talk to Pooniper about it.
adam.
On Fri, 01 Feb 2013 14:09:32 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment,
in
addition to some J-series units that we'll probably replace with
another
pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat
as
usual. Devices get detected properly, node0& node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling
the
interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces
and
fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the
poller
is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state
inserted
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate`
='0',`ifInUcastPkts_delta`
='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the
device,
Can anybody confirm?
Cheers,
JG
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
Nope, v2c is in settings.
Happy to open up a read-only community if you want to test, Just provide me with a src IP off-list.
Adam Armstrong mailto:adama@memetic.org 1 February 2013 4:37 PM Did you mistakenly add the device as SNMPv1?
adam.
On Fri, 01 Feb 2013 15:08:02 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hey mate,
Do you mean 'ifInOctets'& 'ifOutOctets' ? If you do then i'm poo-ie, because the return is 0.
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',
ifInOctets.1 = 0 ifInOctets.2 = 1928549980 ifInOctets.3 = 0 ifInOctets.4 = 0 ifInOctets.6 = 16751052 ifInOctets.7 = 0 ifInOctets.8 = 0 ifInOctets.9 = 0 ifInOctets.10 = 0 ifInOctets.11 = 0 ifInOctets.12 = 0 ifInOctets.13 = 0 ifInOctets.14 = 1895484058 ifInOctets.15 = 0 ifInOctets.16 = 0 ifInOctets.21 = 0 ifInOctets.22 = 16751052 ifInOctets.501 = 0 ifInOctets.502 = 0 ifInOctets.503 = 0 ifInOctets.504 = 0 ifInOctets.505 = 0 ifInOctets.506 = 0 ifInOctets.507 = 0 ifInOctets.508 = 0 ifInOctets.509 = 0 ifInOctets.511 = 0 ifInOctets.512 = 0 ifInOctets.513 = 0 ifInOctets.514 = 0 ifInOctets.516 = 0 ifInOctets.517 = 0 ifInOctets.518 = 0 ifInOctets.519 = 0 ifInOctets.521 = 0 ifInOctets.522 = 0 ifInOctets.524 = 0
Jacob Gardinermailto:jacob@jacobgardiner.com 1 February 2013 2:09 PM Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in addition to some J-series units that we'll probably replace with another pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as usual. Devices get detected properly, node0& node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state inserted SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta` ='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device, Can anybody confirm?
Cheers,
JG
Adam Armstrongmailto:adama@memetic.org 1 February 2013 2:06 PM Further up the debug output you can see the data returned from the switch. You're looking for ifHCInOctets&& ifHCOutOctets.
If the SRX is fucking those up, which I can totally believe for a cluster, you need to talk to Pooniper about it.
adam.
On Fri, 01 Feb 2013 14:09:32 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment,
in
addition to some J-series units that we'll probably replace with
another
pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat
as
usual. Devices get detected properly, node0& node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling
the
interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces
and
fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the
poller
is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state
inserted
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate`
='0',`ifInUcastPkts_delta`
='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs ifInErrors (0 B) 0 Bps 153 secs ifOutErrors (0 B) 0 Bps 153 secs ifInUcastPkts (0 B) 0 Bps 153 secs ifOutUcastPkts (0 B) 0 Bps 153 secsbps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the
device,
Can anybody confirm?
Cheers,
JG
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium Jacob Gardiner mailto:jacob@jacobgardiner.com 1 February 2013 3:08 PM Hey mate,
Do you mean 'ifInOctets' & 'ifOutOctets' ? If you do then i'm poo-ie, because the return is 0.
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',
ifInOctets.1 = 0 ifInOctets.2 = 1928549980 ifInOctets.3 = 0 ifInOctets.4 = 0 ifInOctets.6 = 16751052 ifInOctets.7 = 0 ifInOctets.8 = 0 ifInOctets.9 = 0 ifInOctets.10 = 0 ifInOctets.11 = 0 ifInOctets.12 = 0 ifInOctets.13 = 0 ifInOctets.14 = 1895484058 ifInOctets.15 = 0 ifInOctets.16 = 0 ifInOctets.21 = 0 ifInOctets.22 = 16751052 ifInOctets.501 = 0 ifInOctets.502 = 0 ifInOctets.503 = 0 ifInOctets.504 = 0 ifInOctets.505 = 0 ifInOctets.506 = 0 ifInOctets.507 = 0 ifInOctets.508 = 0 ifInOctets.509 = 0 ifInOctets.511 = 0 ifInOctets.512 = 0 ifInOctets.513 = 0 ifInOctets.514 = 0 ifInOctets.516 = 0 ifInOctets.517 = 0 ifInOctets.518 = 0 ifInOctets.519 = 0 ifInOctets.521 = 0 ifInOctets.522 = 0 ifInOctets.524 = 0 Jacob Gardiner mailto:jacob@jacobgardiner.com 1 February 2013 2:09 PM Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in addition to some J-series units that we'll probably replace with another pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as usual. Devices get detected properly, node0 & node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state inserted SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta` ='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device, Can anybody confirm?
Cheers,
JG
Adam Armstrong mailto:adama@memetic.org 1 February 2013 2:06 PM Further up the debug output you can see the data returned from the switch. You're looking for ifHCInOctets&& ifHCOutOctets.
If the SRX is fucking those up, which I can totally believe for a cluster, you need to talk to Pooniper about it.
adam.
On Fri, 01 Feb 2013 14:09:32 +1100, Jacob Gardiner jacob@jacobgardiner.com wrote:
Hi all,
Firstly - Cheers Adam et all for the development.
I'm looking to see if anybody has had any luck properly monitoring a Juniper SRX cluster. We've got a couple up and running at the moment, in
addition to some J-series units that we'll probably replace with another
pair of SRXs in the future but we've been running into some issues.
Basically when adding the host to observium, everything works a treat as
usual. Devices get detected properly, node0& node1's routing engines get detected properly and we can see two different graphs for each in relation to processor, memory, temperature etc. However when polling the
interfaces, we get a zero response for bps.
This behavior happens on all interfaces except the lo0.X interfaces and fxpX interfaces. (They show graphs and results).
I've run a poll via cmdline with the -d flag and can see that the poller
is definitely seeing a 0 response from all of the other interfaces, output looks something like:
<paste> SQL[INSERT INTO `ports-state` (`port_id`) VALUES ('2151')] state
inserted
SQL[UPDATE `ports-state` set `poll_time` ='1359075465',`poll_period` ='153',`ifInOctets` ='',`ifInOctets_rate` ='0',`ifInOctets_delta` ='0',`ifOutOctets` ='',`ifOutOctets_rate` ='0',`ifOutOctets_delta` ='0',`ifInErrors` ='',`ifInErrors_rate` ='0',`ifInErrors_delta` ='0',`ifOutErrors` ='',`ifOutErrors_rate` ='0',`ifOutErrors_delta` ='0',`ifInUcastPkts` ='',`ifInUcastPkts_rate` ='0',`ifInUcastPkts_delta`
='0',`ifOutUcastPkts` ='',`ifOutUcastPkts_rate` ='0',`ifOutUcastPkts_delta` ='0',`ifInOctets_perc` ='0',`ifOutOctets_perc` ='0',`ifOctets_rate` ='0',`ifUcastPkts_rate` ='0',`ifErrors_rate` ='0' WHERE `port_id` = '2151'] 1 updated Port reth0(568) VLAN == ifInOctets (0 B) 0 Bps 153 secs
ifOutOctets (0 B) 0 Bps 153 secs
ifInErrors (0 B) 0 Bps 153 secs
ifOutErrors (0 B) 0 Bps 153 secs
ifInUcastPkts (0 B) 0 Bps 153 secs
ifOutUcastPkts (0 B) 0 Bps 153 secs bps(0bps/0bps)bytes(0B/0B)pkts(0pps/0pps)OK u:0.00 s:0.03 r:50.09
</paste>
My first impression is that it's the MIB incorrectly polling the device,
Can anybody confirm?
Cheers,
JG
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
participants (2)
-
Adam Armstrong -
Jacob Gardiner