Tp-link switch showing no stats even tho debug shows stats?

newer
Alert Checker not picking up newly...

older
Poseidon2 4002 dry contact check

Simon Mousey Smith

22 Jan 2019 22 Jan '19

4:25 a.m.

Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon

Attachments:

Screenshot2019-01-22at10.23.56.png (image/png — 338.8 KB)
reception.fth (application/octet-stream — 278.7 KB)

Show replies by date

Adam Armstrong

22 Jan 22 Jan

6:04 a.m.

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam. On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org wrote: Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Mike Stupalov

6:09 a.m.

Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

...

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

...
On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org wrote:

Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

Adam Armstrong

6:11 a.m.

Ahh, stupid vendors!

adam. On 2019-01-22 12:09:18, Mike Stupalov via observium observium@observium.org wrote: Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam. On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org [mailto:observium@observium.org] wrote: Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org [mailto:observium@observium.org] http://postman.memetic.org/cgi-bin/mailman/listinfo/observium [http://postman.memetic.org/cgi-bin/mailman/listinfo/observium]

_______________________________________________ observium mailing list observium@observium.org [mailto:observium@observium.org] http://postman.memetic.org/cgi-bin/mailman/listinfo/observium [http://postman.memetic.org/cgi-bin/mailman/listinfo/observium]

-- Mike Stupalov Observium Limited, http://observium.org [http://observium.org]

Markus Klock

6:19 a.m.

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium < observium@observium.org>:

...

Ahh, stupid vendors!

adam.

On 2019-01-22 12:09:18, Mike Stupalov via observium < observium@observium.org> wrote: Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org observium@observium.org wrote: Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing listobservium@observium.orghttp://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Simon Mousey Smith

6:38 a.m.

HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

[1] => array( [ifIndex] => string(1) "1" [ifDescr] => string(18) "Ethernet Interface" [ifType] => string(14) "ethernetCsmacd" [ifMtu] => string(4) "1500" [ifSpeed] => string(10) "1000000000" [ifPhysAddress] => string(17) "d8:5d:4c:86:fd:37" [ifAdminStatus] => string(2) "up" [ifOperStatus] => string(2) "up" [ifLastChange] => string(13) "19:2:38:31.90" [ifInOctets] => string(1) "0" [ifInUcastPkts] => string(9) "104037994" [ifInNUcastPkts] => string(1) "0" [ifInErrors] => string(1) "0" [ifInUnknownProtos] => string(1) "0" [ifOutOctets] => string(9) "595141390" [ifOutUcastPkts] => string(1) "0" [ifOutNUcastPkts] => string(7) "4453773" [ifOutDiscards] => string(1) "0" [ifSpecific] => string(11) "zeroDotZero" [ifName] => string(2) "g1" [ifInMulticastPkts] => string(1) "0" [ifInBroadcastPkts] => string(8) "13670731" [ifOutMulticastPkts] => string(1) "0" [ifOutBroadcastPkts] => string(6) "284703" [ifHCInOctets] => string(1) "0" [ifHCInMulticastPkts] => string(1) "0" [ifHCInBroadcastPkts] => string(1) "0" [ifHCOutOctets] => string(1) "0" [ifHCOutMulticastPkts] => string(1) "0" [ifHCOutBroadcastPkts] => string(1) "0" [ifLinkUpDownTrapEnable] => string(7) "enabled" [ifHighSpeed] => string(1) "0" [ifPromiscuousMode] => string(4) "true" [ifConnectorPresent] => string(4) "true" [ifAlias] => string(6) "MainIn" [ifCounterDiscontinuityTime] => string(12) "0:0:00:00.00" [dot3StatsDuplexStatus] => string(10) "fullDuplex" [ifVlan] => string(1) "1" [ifTrunk] => string(0) "" )

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

...

On 22 Jan 2019, at 12:19, Markus Klock via observium observium@observium.org wrote:

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium <observium@observium.org mailto:observium@observium.org>: Ahh, stupid vendors!

adam.

...
On 2019-01-22 12:09:18, Mike Stupalov via observium <observium@observium.org mailto:observium@observium.org> wrote:

Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

...
Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

...
On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org mailto:observium@observium.org wrote:

Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org http://observium.org/

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Markus Klock

6:59 a.m.

its probably because they do not change. If you poll the ifOutOctets again, has it increased? If its the same every time Observium polls is then the rate is 0 as no new packets have exited that port. /Markus

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium < observium@observium.org>:

...

HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

[1] => array( [ifIndex] => string(1) "1" [ifDescr] => string(18) "Ethernet Interface" [ifType] => string(14) "ethernetCsmacd" [ifMtu] => string(4) "1500" [ifSpeed] => string(10) "1000000000" [ifPhysAddress] => string(17) "d8:5d:4c:86:fd:37" [ifAdminStatus] => string(2) "up" [ifOperStatus] => string(2) "up" [ifLastChange] => string(13) "19:2:38:31.90" [ifInOctets] => string(1) "0" [ifInUcastPkts] => string(9) "104037994" [ifInNUcastPkts] => string(1) "0" [ifInErrors] => string(1) "0" [ifInUnknownProtos] => string(1) "0" [ifOutOctets] => string(9) "595141390" [ifOutUcastPkts] => string(1) "0" [ifOutNUcastPkts] => string(7) "4453773" [ifOutDiscards] => string(1) "0" [ifSpecific] => string(11) "zeroDotZero" [ifName] => string(2) "g1" [ifInMulticastPkts] => string(1) "0" [ifInBroadcastPkts] => string(8) "13670731" [ifOutMulticastPkts] => string(1) "0" [ifOutBroadcastPkts] => string(6) "284703" [ifHCInOctets] => string(1) "0" [ifHCInMulticastPkts] => string(1) "0" [ifHCInBroadcastPkts] => string(1) "0" [ifHCOutOctets] => string(1) "0" [ifHCOutMulticastPkts] => string(1) "0" [ifHCOutBroadcastPkts] => string(1) "0" [ifLinkUpDownTrapEnable] => string(7) "enabled" [ifHighSpeed] => string(1) "0" [ifPromiscuousMode] => string(4) "true" [ifConnectorPresent] => string(4) "true" [ifAlias] => string(6) "MainIn" [ifCounterDiscontinuityTime] => string(12) "0:0:00:00.00" [dot3StatsDuplexStatus] => string(10) "fullDuplex" [ifVlan] => string(1) "1" [ifTrunk] => string(0) "" )

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

On 22 Jan 2019, at 12:19, Markus Klock via observium < observium@observium.org> wrote:

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium < observium@observium.org>:

...
Ahh, stupid vendors!

adam.

On 2019-01-22 12:09:18, Mike Stupalov via observium < observium@observium.org> wrote: Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org observium@observium.org wrote: Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing listobservium@observium.orghttp://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Simon Mousey Smith

7:18 a.m.

Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

...

On 22 Jan 2019, at 12:59, Markus Klock markus@best-practice.se wrote:

its probably because they do not change. If you poll the ifOutOctets again, has it increased? If its the same every time Observium polls is then the rate is 0 as no new packets have exited that port. /Markus

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium <observium@observium.org mailto:observium@observium.org>: HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

[1] => array( [ifIndex] => string(1) "1" [ifDescr] => string(18) "Ethernet Interface" [ifType] => string(14) "ethernetCsmacd" [ifMtu] => string(4) "1500" [ifSpeed] => string(10) "1000000000" [ifPhysAddress] => string(17) "d8:5d:4c:86:fd:37" [ifAdminStatus] => string(2) "up" [ifOperStatus] => string(2) "up" [ifLastChange] => string(13) "19:2:38:31.90" [ifInOctets] => string(1) "0" [ifInUcastPkts] => string(9) "104037994" [ifInNUcastPkts] => string(1) "0" [ifInErrors] => string(1) "0" [ifInUnknownProtos] => string(1) "0" [ifOutOctets] => string(9) "595141390" [ifOutUcastPkts] => string(1) "0" [ifOutNUcastPkts] => string(7) "4453773" [ifOutDiscards] => string(1) "0" [ifSpecific] => string(11) "zeroDotZero" [ifName] => string(2) "g1" [ifInMulticastPkts] => string(1) "0" [ifInBroadcastPkts] => string(8) "13670731" [ifOutMulticastPkts] => string(1) "0" [ifOutBroadcastPkts] => string(6) "284703" [ifHCInOctets] => string(1) "0" [ifHCInMulticastPkts] => string(1) "0" [ifHCInBroadcastPkts] => string(1) "0" [ifHCOutOctets] => string(1) "0" [ifHCOutMulticastPkts] => string(1) "0" [ifHCOutBroadcastPkts] => string(1) "0" [ifLinkUpDownTrapEnable] => string(7) "enabled" [ifHighSpeed] => string(1) "0" [ifPromiscuousMode] => string(4) "true" [ifConnectorPresent] => string(4) "true" [ifAlias] => string(6) "MainIn" [ifCounterDiscontinuityTime] => string(12) "0:0:00:00.00" [dot3StatsDuplexStatus] => string(10) "fullDuplex" [ifVlan] => string(1) "1" [ifTrunk] => string(0) "" )

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

...
On 22 Jan 2019, at 12:19, Markus Klock via observium <observium@observium.org mailto:observium@observium.org> wrote:

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium <observium@observium.org mailto:observium@observium.org>: Ahh, stupid vendors!

adam.

...
On 2019-01-22 12:09:18, Mike Stupalov via observium <observium@observium.org mailto:observium@observium.org> wrote:

Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

...
Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

...
On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org mailto:observium@observium.org wrote:

Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org http://observium.org/

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Mike Stupalov

7:47 a.m.

Change snmp version to v1, this will disable use HC counters.

Here nothing to do in our code, since this is exactly firmware/hardware error.

Simon Mousey Smith via observium wrote on 22.01.19 16:18:

...

Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

...

On 22 Jan 2019, at 12:59, Markus Klock <markus@best-practice.se mailto:markus@best-practice.se> wrote:

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium <observium@observium.org mailto:observium@observium.org>:

HI,

The other strange thing I have noticed if I take my g1 main
interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

  [1]      => array(
[ifIndex]                    => string(1) "1"
          [ifDescr]                    => string(18) "Ethernet
Interface"
                [ifType]   => string(14) "ethernetCsmacd"
[ifMtu]                      => string(4) "1500"
              [ifSpeed]                    => string(10) "1000000000"
                [ifPhysAddress]    => string(17) "d8:5d:4c:86:fd:37"
  [ifAdminStatus]              => string(2) "up"
              [ifOperStatus]               => string(2) "up"
                [ifLastChange]               => string(13)
"19:2:38:31.90"
                [ifInOctets]       => string(1) "0"
[ifInUcastPkts]              => string(9) "104037994"
                [ifInNUcastPkts]             => string(1) "0"
                [ifInErrors] => string(1) "0"
[ifInUnknownProtos]          => string(1) "0"
          [ifOutOctets]                => string(9) "595141390"
                [ifOutUcastPkts]             => string(1) "0"
                [ifOutNUcastPkts]  => string(7) "4453773"
[ifOutDiscards]              => string(1) "0"
          [ifSpecific]                 => string(11) "zeroDotZero"
                [ifName]                     => string(2) "g1"
                [ifInMulticastPkts]  => string(1) "0"
[ifInBroadcastPkts]          => string(8) "13670731"
                [ifOutMulticastPkts]         => string(1) "0"
                [ifOutBroadcastPkts] => string(6) "284703"
[ifHCInOctets]               => string(1) "0"
          [ifHCInMulticastPkts]        => string(1) "0"
                [ifHCInBroadcastPkts]        => string(1) "0"
                [ifHCOutOctets]  => string(1) "0"
[ifHCOutMulticastPkts]       => string(1) "0"
          [ifHCOutBroadcastPkts]       => string(1) "0"
                [ifLinkUpDownTrapEnable]     => string(7) "enabled"
                [ifHighSpeed]  => string(1) "0"
[ifPromiscuousMode]          => string(4) "true"
              [ifConnectorPresent]         => string(4) "true"
                [ifAlias]                    => string(6) "MainIn"
                [ifCounterDiscontinuityTime] => string(12)
"0:0:00:00.00"
[dot3StatsDuplexStatus]      => string(10) "fullDuplex"
                [ifVlan]                     => string(1) "1"
                [ifTrunk]  => string(0) ""
              )


Processing port ifIndex 1 with function process_port_label()
Processing port ifIndex 1 with function process_port_etherlike()
64-bit,
IFLASTCHANGE unknown/false, used system times.
MainIn

 ifInOctets (0 B) 0 Bps 120 secs

 ifOutOctets (0 B) 0 Bps 120 secs

 ifInErrors (0 B) 0 Bps 120 secs

 ifOutErrors (0 B) 0 Bps 120 secs

 ifInUcastPkts (0 B) 0 Bps 120 secs

 ifOutUcastPkts (0 B) 0 Bps 120 secs

 ifInNUcastPkts (0 B) 0 Bps 120 secs

 ifOutNUcastPkts (0 B) 0 Bps 120 secs

 ifInBroadcastPkts (0 B) 0 Bps 120 secs

 ifOutBroadcastPkts (0 B) 0 Bps 120 secs

 ifInMulticastPkts (0 B) 0 Bps 120 secs

 ifOutMulticastPkts (0 B) 0 Bps 120 secs

 ifInDiscards (0 B) 0 Bps 120 secs

 ifOutDiscards (0 B) 0 Bps 120 secs


Regards

Simon

...

On 22 Jan 2019, at 12:19, Markus Klock via observium
<observium@observium.org <mailto:observium@observium.org>> wrote:

When a vendor fails to even implement IF-MIB you know they suck
at SNMP...
/Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium
<observium@observium.org <mailto:observium@observium.org>>:

    Ahh, stupid vendors!

    adam.

...

    On 2019-01-22 12:09:18, Mike Stupalov via observium
    <observium@observium.org <mailto:observium@observium.org>>
    wrote:

    Hi,

     write to vendor.. this device return empty counters (and
    not for all indexes):

    ifHCInOctets.1 = 0
    ifHCInOctets.2 = 0
    ifHCInOctets.3 = 0
    ifHCInOctets.4 = 0
    ifHCInOctets.5 = 0

    ifHCOutOctets.1 = 0
    ifHCOutOctets.2 = 0
    ifHCOutOctets.3 = 0
    ifHCOutOctets.4 = 0

    but some ports still return non-HC counters:
    ifInOctets.6 = 1133938806
    ifInOctets.7 = 555769688

    ifOutOctets.1 = 595141390
    ifOutOctets.2 = 708574072
    ifOutOctets.3 = 4019307600
    ifOutOctets.4 = 0
    ifOutOctets.5 = 0
    ifOutOctets.6 = 1351693276
    ifOutOctets.7 = 1926878970

    but anyway - we prefer HC counters,
    and randomly empty counters seems as device or firmware broken.

    Adam Armstrong via observium wrote on 22.01.19 15:04:

...

    Walk ifInOctets and ifOutOctets and see if those ports'
    counters are changing over time.

    adam.

...

    On 2019-01-22 10:25:46, Simon Mousey Smith via observium
    <observium@observium.org>
    <mailto:observium@observium.org> wrote:

    Hi All,

    Im trying to work out if the is something wrong with my
    switch or observium?

    Observium detects all the ports fine, vlans fine,

    But its not showing any traffic on the ports?

    And when I run the -dd in the poller.php the output shows
    that the is traffic on the ports?

    Attached is the debug and a screenshot showing the ports
    in observium

    Regards

    Simon_______________________________________________
    observium mailing list
    observium@observium.org <mailto:observium@observium.org>
    http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

    _______________________________________________
    observium mailing list
    observium@observium.org <mailto:observium@observium.org>
    http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

    -- 
    Mike Stupalov
    Observium Limited, http://observium.org <http://observium.org/>

    _______________________________________________
    observium mailing list
    observium@observium.org <mailto:observium@observium.org>
    http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

_______________________________________________
observium mailing list
observium@observium.org <mailto:observium@observium.org>
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

_______________________________________________
observium mailing list
observium@observium.org <mailto:observium@observium.org>
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

Simon Mousey Smith

7:58 a.m.

Legend Mike!

Thank you!

Dunno why I didn’t try v1 before hand!

Its now showing stats for each port including vlans

Regards

Simon

...

On 22 Jan 2019, at 13:47, Mike Stupalov via observium observium@observium.org wrote:

Change snmp version to v1, this will disable use HC counters.

Here nothing to do in our code, since this is exactly firmware/hardware error.

Simon Mousey Smith via observium wrote on 22.01.19 16:18:

...
Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

...
On 22 Jan 2019, at 12:59, Markus Klock <markus@best-practice.se mailto:markus@best-practice.se> wrote:

its probably because they do not change. If you poll the ifOutOctets again, has it increased? If its the same every time Observium polls is then the rate is 0 as no new packets have exited that port. /Markus

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium <observium@observium.org mailto:observium@observium.org>: HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

[1] => array( [ifIndex] => string(1) "1" [ifDescr] => string(18) "Ethernet Interface" [ifType] => string(14) "ethernetCsmacd" [ifMtu] => string(4) "1500" [ifSpeed] => string(10) "1000000000" [ifPhysAddress] => string(17) "d8:5d:4c:86:fd:37" [ifAdminStatus] => string(2) "up" [ifOperStatus] => string(2) "up" [ifLastChange] => string(13) "19:2:38:31.90" [ifInOctets] => string(1) "0" [ifInUcastPkts] => string(9) "104037994" [ifInNUcastPkts] => string(1) "0" [ifInErrors] => string(1) "0" [ifInUnknownProtos] => string(1) "0" [ifOutOctets] => string(9) "595141390" [ifOutUcastPkts] => string(1) "0" [ifOutNUcastPkts] => string(7) "4453773" [ifOutDiscards] => string(1) "0" [ifSpecific] => string(11) "zeroDotZero" [ifName] => string(2) "g1" [ifInMulticastPkts] => string(1) "0" [ifInBroadcastPkts] => string(8) "13670731" [ifOutMulticastPkts] => string(1) "0" [ifOutBroadcastPkts] => string(6) "284703" [ifHCInOctets] => string(1) "0" [ifHCInMulticastPkts] => string(1) "0" [ifHCInBroadcastPkts] => string(1) "0" [ifHCOutOctets] => string(1) "0" [ifHCOutMulticastPkts] => string(1) "0" [ifHCOutBroadcastPkts] => string(1) "0" [ifLinkUpDownTrapEnable] => string(7) "enabled" [ifHighSpeed] => string(1) "0" [ifPromiscuousMode] => string(4) "true" [ifConnectorPresent] => string(4) "true" [ifAlias] => string(6) "MainIn" [ifCounterDiscontinuityTime] => string(12) "0:0:00:00.00" [dot3StatsDuplexStatus] => string(10) "fullDuplex" [ifVlan] => string(1) "1" [ifTrunk] => string(0) "" )

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

...
On 22 Jan 2019, at 12:19, Markus Klock via observium <observium@observium.org mailto:observium@observium.org> wrote:

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium <observium@observium.org mailto:observium@observium.org>: Ahh, stupid vendors!

adam.

...
On 2019-01-22 12:09:18, Mike Stupalov via observium <observium@observium.org mailto:observium@observium.org> wrote:

Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

...
Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam. > On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org mailto:observium@observium.org wrote: > > Hi All, > > Im trying to work out if the is something wrong with my switch or observium? > > Observium detects all the ports fine, vlans fine, > > But its not showing any traffic on the ports? > > And when I run the -dd in the poller.php the output shows that the is traffic on the ports? > > Attached is the debug and a screenshot showing the ports in observium > > Regards > > Simon_______________________________________________ > observium mailing list > observium@observium.org mailto:observium@observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org http://observium.org/

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org http://observium.org/ _______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Adam Armstrong

7:04 p.m.

Though perhaps a method to disable use of HC counters on a per-device basis might be useful.

There are other benefits of V2, like bulkwalk! :)

adam. On 2019-01-22 13:47:25, Mike Stupalov via observium observium@observium.org wrote: Change snmp version to v1, this will disable use HC counters.

Here nothing to do in our code, since this is exactly firmware/hardware error.

Simon Mousey Smith via observium wrote on 22.01.19 16:18:

Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

On 22 Jan 2019, at 12:59, Markus Klock <markus@best-practice.se [mailto:markus@best-practice.se]> wrote:

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium <observium@observium.org [mailto:observium@observium.org]>:

HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

On 22 Jan 2019, at 12:19, Markus Klock via observium <observium@observium.org [mailto:observium@observium.org]> wrote:

When a vendor fails to even implement IF-MIB you know they suck at SNMP... /Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium <observium@observium.org [mailto:observium@observium.org]>:

Ahh, stupid vendors!

adam. On 2019-01-22 12:09:18, Mike Stupalov via observium <observium@observium.org [mailto:observium@observium.org]> wrote: Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam. On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org [mailto:observium@observium.org] wrote: Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

-- Mike Stupalov Observium Limited, http://observium.org [http://observium.org/]

-- Mike Stupalov Observium Limited, http://observium.org [http://observium.org]

Mike Stupalov

23 Jan 23 Jan

1:53 a.m.

Adam Armstrong via observium wrote on 23/01/2019 04:04:

...

Though perhaps a method to disable use of HC counters on a per-device basis might be useful.

There are other benefits of V2, like bulkwalk! :)

for this devices (as I see in output) bulkwalk also broken..

...

adam.

...
On 2019-01-22 13:47:25, Mike Stupalov via observium observium@observium.org wrote:

Change snmp version to v1, this will disable use HC counters.

Here nothing to do in our code, since this is exactly firmware/hardware error.

Simon Mousey Smith via observium wrote on 22.01.19 16:18:

...
Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

...
On 22 Jan 2019, at 12:59, Markus Klock <markus@best-practice.se mailto:markus@best-practice.se> wrote:

its probably because they do not change. If you poll the ifOutOctets again, has it increased? If its the same every time Observium polls is then the rate is 0 as no new packets have exited that port. /Markus

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium <observium@observium.org mailto:observium@observium.org>:
HI,

The other strange thing I have noticed if I take my g1 main
interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

  [1]      => array(
[ifIndex]                    => string(1) "1"
          [ifDescr]                    => string(18) "Ethernet
Interface"
                [ifType]   => string(14) "ethernetCsmacd"
[ifMtu]                      => string(4) "1500"
              [ifSpeed]                    => string(10)
"1000000000"
                [ifPhysAddress]    => string(17)
"d8:5d:4c:86:fd:37"
  [ifAdminStatus]              => string(2) "up"
              [ifOperStatus]               => string(2) "up"
                [ifLastChange]               => string(13)
"19:2:38:31.90"
                [ifInOctets]       => string(1) "0"
[ifInUcastPkts]              => string(9) "104037994"
                [ifInNUcastPkts]             => string(1) "0"
                [ifInErrors] => string(1) "0"
[ifInUnknownProtos]          => string(1) "0"
          [ifOutOctets]                => string(9) "595141390"
                [ifOutUcastPkts]             => string(1) "0"
                [ifOutNUcastPkts]  => string(7) "4453773"
[ifOutDiscards]              => string(1) "0"
          [ifSpecific]                 => string(11) "zeroDotZero"
                [ifName]                     => string(2) "g1"
                [ifInMulticastPkts]  => string(1) "0"
[ifInBroadcastPkts]          => string(8) "13670731"
                [ifOutMulticastPkts]         => string(1) "0"
                [ifOutBroadcastPkts] => string(6) "284703"
[ifHCInOctets]               => string(1) "0"
          [ifHCInMulticastPkts]        => string(1) "0"
                [ifHCInBroadcastPkts]        => string(1) "0"
                [ifHCOutOctets]  => string(1) "0"
[ifHCOutMulticastPkts]       => string(1) "0"
          [ifHCOutBroadcastPkts]       => string(1) "0"
                [ifLinkUpDownTrapEnable]     => string(7) "enabled"
                [ifHighSpeed]  => string(1) "0"
[ifPromiscuousMode]          => string(4) "true"
              [ifConnectorPresent]         => string(4) "true"
                [ifAlias]                    => string(6) "MainIn"
                [ifCounterDiscontinuityTime] => string(12)
"0:0:00:00.00"
[dot3StatsDuplexStatus]      => string(10) "fullDuplex"
                [ifVlan]                     => string(1) "1"
                [ifTrunk]  => string(0) ""
              )


Processing port ifIndex 1 with function process_port_label()
Processing port ifIndex 1 with function process_port_etherlike()
64-bit,
IFLASTCHANGE unknown/false, used system times.
MainIn

 ifInOctets (0 B) 0 Bps 120 secs

 ifOutOctets (0 B) 0 Bps 120 secs

 ifInErrors (0 B) 0 Bps 120 secs

 ifOutErrors (0 B) 0 Bps 120 secs

 ifInUcastPkts (0 B) 0 Bps 120 secs

 ifOutUcastPkts (0 B) 0 Bps 120 secs

 ifInNUcastPkts (0 B) 0 Bps 120 secs

 ifOutNUcastPkts (0 B) 0 Bps 120 secs

 ifInBroadcastPkts (0 B) 0 Bps 120 secs

 ifOutBroadcastPkts (0 B) 0 Bps 120 secs

 ifInMulticastPkts (0 B) 0 Bps 120 secs

 ifOutMulticastPkts (0 B) 0 Bps 120 secs

 ifInDiscards (0 B) 0 Bps 120 secs

 ifOutDiscards (0 B) 0 Bps 120 secs


Regards

Simon
...
On 22 Jan 2019, at 12:19, Markus Klock via observium
<observium@observium.org <mailto:observium@observium.org>> wrote:

When a vendor fails to even implement IF-MIB you know they
suck at SNMP...
/Markus

Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via
observium <observium@observium.org
<mailto:observium@observium.org>>:

    Ahh, stupid vendors!

    adam.
...
    On 2019-01-22 12:09:18, Mike Stupalov via observium
    <observium@observium.org
    <mailto:observium@observium.org>> wrote:

    Hi,

     write to vendor.. this device return empty counters (and
    not for all indexes):

    ifHCInOctets.1 = 0
    ifHCInOctets.2 = 0
    ifHCInOctets.3 = 0
    ifHCInOctets.4 = 0
    ifHCInOctets.5 = 0

    ifHCOutOctets.1 = 0
    ifHCOutOctets.2 = 0
    ifHCOutOctets.3 = 0
    ifHCOutOctets.4 = 0

    but some ports still return non-HC counters:
    ifInOctets.6 = 1133938806
    ifInOctets.7 = 555769688

    ifOutOctets.1 = 595141390
    ifOutOctets.2 = 708574072
    ifOutOctets.3 = 4019307600
    ifOutOctets.4 = 0
    ifOutOctets.5 = 0
    ifOutOctets.6 = 1351693276
    ifOutOctets.7 = 1926878970

    but anyway - we prefer HC counters,
    and randomly empty counters seems as device or firmware
    broken.

    Adam Armstrong via observium wrote on 22.01.19 15:04:
> Walk ifInOctets and ifOutOctets and see if those ports' > counters are changing over time. > > adam. >> >> On 2019-01-22 10:25:46, Simon Mousey Smith via >> observium observium@observium.org >> mailto:observium@observium.org wrote: >> >> Hi All, >> >> Im trying to work out if the is something wrong with my >> switch or observium? >> >> Observium detects all the ports fine, vlans fine, >> >> But its not showing any traffic on the ports? >> >> And when I run the -dd in the poller.php the output >> shows that the is traffic on the ports? >> >> Attached is the debug and a screenshot showing the >> ports in observium >> >> Regards >> >> Simon_______________________________________________ >> observium mailing list >> observium@observium.org mailto:observium@observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > _______________________________________________ > observium mailing list > observium@observium.org mailto:observium@observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
    -- 
    Mike Stupalov
    Observium Limited, http://observium.org
    <http://observium.org/>
    _______________________________________________
    observium mailing list
    observium@observium.org <mailto:observium@observium.org>
    http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

_______________________________________________
observium mailing list
observium@observium.org <mailto:observium@observium.org>
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
_______________________________________________
observium mailing list
observium@observium.org <mailto:observium@observium.org>
http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium
-- Mike Stupalov Observium Limited, http://observium.org
observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

Simon Mousey Smith

5:24 a.m.

The outputs I sent was v2 instead of v1

And I did notice the time go up on the pollen for that device from 5 sec to 15sec when switching from v2 to v1

So maybe if it’s possible to disable the hc per device would be handy :)

Regards

Simon

Sent from my iPad

...

On 23 Jan 2019, at 07:53, Mike Stupalov via observium observium@observium.org wrote:

Adam Armstrong via observium wrote on 23/01/2019 04:04:

...
Though perhaps a method to disable use of HC counters on a per-device basis might be useful.

There are other benefits of V2, like bulkwalk! :)

for this devices (as I see in output) bulkwalk also broken..

...
adam.

...
On 2019-01-22 13:47:25, Mike Stupalov via observium observium@observium.org wrote:

Change snmp version to v1, this will disable use HC counters.

Here nothing to do in our code, since this is exactly firmware/hardware error.

Simon Mousey Smith via observium wrote on 22.01.19 16:18:

...
Hi,

Ok im more confused now

I added 3 more of the same switches to monitor, and ive just noticed the first 4 ports on each of the switches dont have stats? But the other 5 ports do? And plans do too?

But what I’ve also noticed in the section=ports page, the first 4 ports are 64bit and the rest are 32bit?

Could this be the problem?

And also from the looks of it, YES the ifOutOctets does increase each poller cycle

Attached is a second poller output with debug

Regards

Simon

...
On 22 Jan 2019, at 12:59, Markus Klock markus@best-practice.se wrote:

its probably because they do not change. If you poll the ifOutOctets again, has it increased? If its the same every time Observium polls is then the rate is 0 as no new packets have exited that port. /Markus

Den tis 22 jan. 2019 kl 13:38 skrev Simon Mousey Smith via observium observium@observium.org:

...
HI,

The other strange thing I have noticed if I take my g1 main interface in port

Yes the ifInOctets are 0, but the ifOutOctets are 595141390

But yet observium is showing ifOutOctets as 0 ???

Same with broadcastpkts?

Any ideas?

[1] => array( [ifIndex] => string(1) "1" [ifDescr] => string(18) "Ethernet Interface" [ifType] => string(14) "ethernetCsmacd" [ifMtu] => string(4) "1500" [ifSpeed] => string(10) "1000000000" [ifPhysAddress] => string(17) "d8:5d:4c:86:fd:37" [ifAdminStatus] => string(2) "up" [ifOperStatus] => string(2) "up" [ifLastChange] => string(13) "19:2:38:31.90" [ifInOctets] => string(1) "0" [ifInUcastPkts] => string(9) "104037994" [ifInNUcastPkts] => string(1) "0" [ifInErrors] => string(1) "0" [ifInUnknownProtos] => string(1) "0" [ifOutOctets] => string(9) "595141390" [ifOutUcastPkts] => string(1) "0" [ifOutNUcastPkts] => string(7) "4453773" [ifOutDiscards] => string(1) "0" [ifSpecific] => string(11) "zeroDotZero" [ifName] => string(2) "g1" [ifInMulticastPkts] => string(1) "0" [ifInBroadcastPkts] => string(8) "13670731" [ifOutMulticastPkts] => string(1) "0" [ifOutBroadcastPkts] => string(6) "284703" [ifHCInOctets] => string(1) "0" [ifHCInMulticastPkts] => string(1) "0" [ifHCInBroadcastPkts] => string(1) "0" [ifHCOutOctets] => string(1) "0" [ifHCOutMulticastPkts] => string(1) "0" [ifHCOutBroadcastPkts] => string(1) "0" [ifLinkUpDownTrapEnable] => string(7) "enabled" [ifHighSpeed] => string(1) "0" [ifPromiscuousMode] => string(4) "true" [ifConnectorPresent] => string(4) "true" [ifAlias] => string(6) "MainIn" [ifCounterDiscontinuityTime] => string(12) "0:0:00:00.00" [dot3StatsDuplexStatus] => string(10) "fullDuplex" [ifVlan] => string(1) "1" [ifTrunk] => string(0) "" )

Processing port ifIndex 1 with function process_port_label() Processing port ifIndex 1 with function process_port_etherlike() 64-bit, IFLASTCHANGE unknown/false, used system times. MainIn

ifInOctets (0 B) 0 Bps 120 secs

ifOutOctets (0 B) 0 Bps 120 secs

ifInErrors (0 B) 0 Bps 120 secs

ifOutErrors (0 B) 0 Bps 120 secs

ifInUcastPkts (0 B) 0 Bps 120 secs

ifOutUcastPkts (0 B) 0 Bps 120 secs

ifInNUcastPkts (0 B) 0 Bps 120 secs

ifOutNUcastPkts (0 B) 0 Bps 120 secs

ifInBroadcastPkts (0 B) 0 Bps 120 secs

ifOutBroadcastPkts (0 B) 0 Bps 120 secs

ifInMulticastPkts (0 B) 0 Bps 120 secs

ifOutMulticastPkts (0 B) 0 Bps 120 secs

ifInDiscards (0 B) 0 Bps 120 secs

ifOutDiscards (0 B) 0 Bps 120 secs

Regards

Simon

> On 22 Jan 2019, at 12:19, Markus Klock via observium observium@observium.org wrote: > > When a vendor fails to even implement IF-MIB you know they suck at SNMP... > /Markus > > Den tis 22 jan. 2019 kl 13:11 skrev Adam Armstrong via observium observium@observium.org: >> Ahh, stupid vendors! >> >> adam. >>> On 2019-01-22 12:09:18, Mike Stupalov via observium observium@observium.org wrote: >>> >>> Hi, >>> >>> write to vendor.. this device return empty counters (and not for all indexes): >>> >>> ifHCInOctets.1 = 0 >>> ifHCInOctets.2 = 0 >>> ifHCInOctets.3 = 0 >>> ifHCInOctets.4 = 0 >>> ifHCInOctets.5 = 0 >>> >>> ifHCOutOctets.1 = 0 >>> ifHCOutOctets.2 = 0 >>> ifHCOutOctets.3 = 0 >>> ifHCOutOctets.4 = 0 >>> >>> but some ports still return non-HC counters: >>> ifInOctets.6 = 1133938806 >>> ifInOctets.7 = 555769688 >>> >>> ifOutOctets.1 = 595141390 >>> ifOutOctets.2 = 708574072 >>> ifOutOctets.3 = 4019307600 >>> ifOutOctets.4 = 0 >>> ifOutOctets.5 = 0 >>> ifOutOctets.6 = 1351693276 >>> ifOutOctets.7 = 1926878970 >>> >>> but anyway - we prefer HC counters, >>> and randomly empty counters seems as device or firmware broken. >>> >>> Adam Armstrong via observium wrote on 22.01.19 15:04: >>>> Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time. >>>> >>>> adam. >>>>> On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org wrote: >>>>> >>>>> Hi All, >>>>> >>>>> Im trying to work out if the is something wrong with my switch or observium? >>>>> >>>>> Observium detects all the ports fine, vlans fine, >>>>> >>>>> But its not showing any traffic on the ports? >>>>> >>>>> And when I run the -dd in the poller.php the output shows that the is traffic on the ports? >>>>> >>>>> Attached is the debug and a screenshot showing the ports in observium >>>>> >>>>> Regards >>>>> >>>>> Simon_______________________________________________ >>>>> observium mailing list >>>>> observium@observium.org >>>>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >>>> >>>> _______________________________________________ >>>> observium mailing list >>>> observium@observium.org >>>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >>> >>> -- >>> Mike Stupalov >>> Observium Limited, http://observium.org >> _______________________________________________ >> observium mailing list >> observium@observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > _______________________________________________ > observium mailing list > observium@observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Simon Mousey Smith

22 Jan 22 Jan

6:20 a.m.

Hi,

Sadly the is no other firmwares available for this device and TP-Link dont wanna no cuz they want me to use one of there ’newer’ models :eyeroll:

Can you at all change the code slightly so it maybe uses the ifIn and IfOut instead of the ifHC for this particular model?

sysObjectID =>. .1.3.6.1.4.1.11863.100.103

TL-SG3109 V1

Regards

Simon

...

On 22 Jan 2019, at 12:11, Adam Armstrong via observium observium@observium.org wrote:

Ahh, stupid vendors!

adam.

...
On 2019-01-22 12:09:18, Mike Stupalov via observium observium@observium.org wrote:

Hi,

write to vendor.. this device return empty counters (and not for all indexes):

ifHCInOctets.1 = 0 ifHCInOctets.2 = 0 ifHCInOctets.3 = 0 ifHCInOctets.4 = 0 ifHCInOctets.5 = 0

ifHCOutOctets.1 = 0 ifHCOutOctets.2 = 0 ifHCOutOctets.3 = 0 ifHCOutOctets.4 = 0

but some ports still return non-HC counters: ifInOctets.6 = 1133938806 ifInOctets.7 = 555769688

ifOutOctets.1 = 595141390 ifOutOctets.2 = 708574072 ifOutOctets.3 = 4019307600 ifOutOctets.4 = 0 ifOutOctets.5 = 0 ifOutOctets.6 = 1351693276 ifOutOctets.7 = 1926878970

but anyway - we prefer HC counters, and randomly empty counters seems as device or firmware broken.

Adam Armstrong via observium wrote on 22.01.19 15:04:

...
Walk ifInOctets and ifOutOctets and see if those ports' counters are changing over time.

adam.

...
On 2019-01-22 10:25:46, Simon Mousey Smith via observium observium@observium.org mailto:observium@observium.org wrote:

Hi All,

Im trying to work out if the is something wrong with my switch or observium?

Observium detects all the ports fine, vlans fine,

But its not showing any traffic on the ports?

And when I run the -dd in the poller.php the output shows that the is traffic on the ports?

Attached is the debug and a screenshot showing the ports in observium

Regards

Simon_______________________________________________ observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

observium mailing list observium@observium.org mailto:observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

-- Mike Stupalov Observium Limited, http://observium.org http://observium.org/

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

2206

Age (days ago)

2207

Last active (days ago)

List overview

Download

13 comments

4 participants

tags (0)

participants (4)

Adam Armstrong
Markus Klock
Mike Stupalov
Simon Mousey Smith