It looks like the cron jobs aren't actually running.

Adam.

Sent with AquaMail for Android http://www.aqua-mail.com

On 16 November 2015 10:19:59 Federico Olivieri lvrfrc87@gmail.com wrote:

Hi Adam,

My bad, I have missed one step during the set-up. I can see the UNIX-client in my remote serer. However, I have another question/problem:

I added the snmp client to my snmp remote and it is fine. Then I set-up observium in the client and I try to pull the data from itself (Basically the same device is polled from a remote server and from itself) I can add the device (on the local observium) but I cannot pool any data (see screenshot). Below you can find the config for snmpd

[image: Immagine incorporata 1]

# AGENT BEHAVIOUR

#

# Listen for connections from the local system only

#agentAddress udp:127.0.0.1:161

# Listen for connections on all interfaces (both IPv4 *and* IPv6)

agentAddress udp:161,udp6:[::1]:161 # ACCESS CONTROL #

                                             #  system + hrSystem

groups only view systemonly included .1.3.6.1.2.1.1 view systemonly included .1.3.6.1.2.1.25.1

                                             #  Full access from the

local host rocommunity public localhost # Default access to basic system info #rocommunity public default -V systemonly # rocommunity6 is for IPv6 #rocommunity6 public default -V systemonly

                                             #  Full access from an

example network # Adjust this network address to match your local # settings, change the community string, # and check the 'agentAddress' setting above rocommunity secret 87.81.223.210

                                             #  Full read-only access

for SNMPv3 rouser authOnlyUser

Thakls!

On 15 Nov 2015 18:14, "Adam Armstrong" adama@memetic.org wrote:

...

Hi Frederico,

You install the agent in the same way, it's not difficult!

What exactly isn't working?

adam.

On 15/11/2015 16:16:26, Federico Olivieri lvrfrc87@gmail.com wrote: Hi All

I have a server that is running Observium with Unix Agent and everything is ok. Recently I installed a second remote server and is a SNMP client on my observium. Because this server is running Power DNS I would enable the UNIX-AGENT om this client and see the graphs for pdns on my Observium.

Can anyone assist me on this?

Thank You very much

Federico _______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

---

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

---

---

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

Yes, That was the problem! Thanks Adam. BTW seems that corn works properly with this snmpd conf

Federico

2015-11-16 10:50 GMT+00:00 Adam Armstrong adama@observium.org:

Also, you're using a restrictive SNMP config which won't work even if the cron jobs are running.

Adam.

Sent with AquaMail for Android http://www.aqua-mail.com

On 16 November 2015 10:19:59 Federico Olivieri lvrfrc87@gmail.com wrote:

...

Hi Adam,

My bad, I have missed one step during the set-up. I can see the UNIX-client in my remote serer. However, I have another question/problem:

I added the snmp client to my snmp remote and it is fine. Then I set-up observium in the client and I try to pull the data from itself (Basically the same device is polled from a remote server and from itself) I can add the device (on the local observium) but I cannot pool any data (see screenshot). Below you can find the config for snmpd

[image: Immagine incorporata 1]

# AGENT BEHAVIOUR

#

# Listen for connections from the local system only

#agentAddress udp:127.0.0.1:161

# Listen for connections on all interfaces (both IPv4 *and* IPv6)

agentAddress udp:161,udp6:[::1]:161 # ACCESS CONTROL #

                                             #  system + hrSystem

groups only view systemonly included .1.3.6.1.2.1.1 view systemonly included .1.3.6.1.2.1.25.1

                                             #  Full access from the

local host rocommunity public localhost # Default access to basic system info #rocommunity public default -V systemonly # rocommunity6 is for IPv6 #rocommunity6 public default -V systemonly

                                             #  Full access from an

example network # Adjust this network address to match your local # settings, change the community string, # and check the 'agentAddress' setting above rocommunity secret 87.81.223.210

                                             #  Full read-only access

for SNMPv3 rouser authOnlyUser

Thakls!

On 15 Nov 2015 18:14, "Adam Armstrong" adama@memetic.org wrote:

...

Hi Frederico,

You install the agent in the same way, it's not difficult!

What exactly isn't working?

adam.

On 15/11/2015 16:16:26, Federico Olivieri lvrfrc87@gmail.com wrote: Hi All

I have a server that is running Observium with Unix Agent and everything is ok. Recently I installed a second remote server and is a SNMP client on my observium. Because this server is running Power DNS I would enable the UNIX-AGENT om this client and see the graphs for pdns on my Observium.

Can anyone assist me on this?

Thank You very much

Federico _______________________________________________ observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

---

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

---

observium mailing list observium@observium.org http:/​/​postman​.​memetic​.​org/​cgi-bin/​mailman/​listinfo/​observium http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

---

observium mailing list observium@observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium