Hi, sorry if this is obvious, but it just occurred to me that I don't understand this graph. This comes from an Ethernet port on a cisco router.... [cid:image001.jpg@01DA26BB.DFC59A20]
What are the units??for example the "last in errors/s" is 44.25m???? 44.24 million? That can't be right.
Thanks in advance
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
Just for reference, this is the "show interface" for the port in the graph...I understand that "show interface" shows a cumulative number while the graph is not....but as you can see, there have been 1241 input errors since the last reset.....that is no where near 44m?
Hence my confusion thanks
GigabitEthernet0/0 is up, line protocol is up Hardware is CN Gigabit Ethernet, address is 68ef.bd99.dca0 (bia 68ef.bd99.dca0 ) Description: lan Internet address is 1.1.1.1/24 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full Duplex, 1Gbps, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/13/11228 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 954000 bits/sec, 535 packets/sec 5 minute output rate 8346000 bits/sec, 885 packets/sec 3637522994 packets input, 1559853723 bytes, 0 no buffer Received 11917322 broadcasts (0 IP multicasts) 0 runts, 0 giants, 1 throttles 1241 input errors, 0 CRC, 0 frame, 1241 overrun, 0 ignored 0 watchdog, 177941 multicast, 0 pause input 322101698 packets output, 1529083260 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 403 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Tony Guadagno via observium observium@lists.observium.org Sent: Monday, December 4, 2023 2:12 PM To: Observium observium@lists.observium.org Cc: Tony Guadagno tonyg@guadagno.org Subject: [Observium] units on error graphs?
Hi, sorry if this is obvious, but it just occurred to me that I don't understand this graph. This comes from an Ethernet port on a cisco router.... [cid:image001.jpg@01DA26C0.A3113080]
What are the units??for example the "last in errors/s" is 44.25m???? 44.24 million? That can't be right.
Thanks in advance
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
The graph is showing a rate, so it's errors per second, or 44 milli-errors per second or something like 13 errors in the 5 minute poller period.
adam.
Tony Guadagno via observium wrote on 2023-12-04 19:46:
Just for reference, this is the “show interface” for the port in the graph…I understand that “show interface” shows a cumulative number while the graph is not….but as you can see, there have been 1241 input errors since the last reset…..that is no where near 44m?
Hence my confusion
thanks
GigabitEthernet0/0 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 68ef.bd99.dca0 (bia 68ef.bd99.dca0 )
Description: lan
Internet address is 1.1.1.1/24
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/13/11228 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 954000 bits/sec, 535 packets/sec
5 minute output rate 8346000 bits/sec, 885 packets/sec
3637522994 packets input, 1559853723 bytes, 0 no buffer
Received 11917322 broadcasts (0 IP multicasts)
0 runts, 0 giants, 1 throttles
1241 input errors, 0 CRC, 0 frame, 1241 overrun, 0 ignored
0 watchdog, 177941 multicast, 0 pause input
322101698 packets output, 1529083260 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
403 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Tony Guadagno
O +1 585 577 1003
C +1 585 703 6700
E tonyg@guadagnoconsulting.com mailto:tonyg@guadagnoconsulting.com
cid:image001.jpg@01D84DD6.FC9912E0
*From:* Tony Guadagno via observium observium@lists.observium.org *Sent:* Monday, December 4, 2023 2:12 PM *To:* Observium observium@lists.observium.org *Cc:* Tony Guadagno tonyg@guadagno.org *Subject:* [Observium] units on error graphs?
Hi, sorry if this is obvious, but it just occurred to me that I don’t understand this graph. This comes from an Ethernet port on a cisco router….
What are the units??for example the “last in errors/s” is 44.25m???? 44.24 million? That can’t be right.
Thanks in advance
Tony Guadagno
O +1 585 577 1003
C +1 585 703 6700
E tonyg@guadagnoconsulting.com mailto:tonyg@guadagnoconsulting.com
cid:image001.jpg@01D84DD6.FC9912E0
observium mailing list -- observium@lists.observium.org To unsubscribe send an email to observium-leave@lists.observium.org
Aahhh.... Milli-errors... LOL how could I have missed that...
Ok, that clears that up, thanks!
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Adam Armstrong via observium observium@lists.observium.org Sent: Monday, December 4, 2023 3:35 PM To: Tony Guadagno via observium observium@lists.observium.org Cc: Adam Armstrong adama@observium.org Subject: [Observium] Re: units on error graphs?
The graph is showing a rate, so it's errors per second, or 44 milli-errors per second or something like 13 errors in the 5 minute poller period.
adam.
Tony Guadagno via observium wrote on 2023-12-04 19:46:
Just for reference, this is the "show interface" for the port in the graph...I understand that "show interface" shows a cumulative number while the graph is not....but as you can see, there have been 1241 input errors since the last reset.....that is no where near 44m?
Hence my confusion thanks
GigabitEthernet0/0 is up, line protocol is up Hardware is CN Gigabit Ethernet, address is 68ef.bd99.dca0 (bia 68ef.bd99.dca0 ) Description: lan Internet address is 1.1.1.1/24 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full Duplex, 1Gbps, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/13/11228 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 954000 bits/sec, 535 packets/sec 5 minute output rate 8346000 bits/sec, 885 packets/sec 3637522994 packets input, 1559853723 bytes, 0 no buffer Received 11917322 broadcasts (0 IP multicasts) 0 runts, 0 giants, 1 throttles 1241 input errors, 0 CRC, 0 frame, 1241 overrun, 0 ignored 0 watchdog, 177941 multicast, 0 pause input 322101698 packets output, 1529083260 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 403 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Tony Guadagno via observium observium@lists.observium.orgmailto:observium@lists.observium.org Sent: Monday, December 4, 2023 2:12 PM To: Observium observium@lists.observium.orgmailto:observium@lists.observium.org Cc: Tony Guadagno tonyg@guadagno.orgmailto:tonyg@guadagno.org Subject: [Observium] units on error graphs?
Hi, sorry if this is obvious, but it just occurred to me that I don't understand this graph. This comes from an Ethernet port on a cisco router.... [cid:image004.jpg@01DA26C8.8C73E090]
What are the units??for example the "last in errors/s" is 44.25m???? 44.24 million? That can't be right.
Thanks in advance
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
_______________________________________________
observium mailing list -- observium@lists.observium.orgmailto:observium@lists.observium.org
To unsubscribe send an email to observium-leave@lists.observium.orgmailto:observium-leave@lists.observium.org
Quite a few people don't make the connection on that graph in particular!
Tony Guadagno via observium wrote on 2023-12-04 20:42:
Aahhh…. Milli-errors… LOL how could I have missed that…
Ok, that clears that up, thanks!
Tony Guadagno
O +1 585 577 1003
C +1 585 703 6700
E tonyg@guadagnoconsulting.com mailto:tonyg@guadagnoconsulting.com
cid:image001.jpg@01D84DD6.FC9912E0
*From:*Adam Armstrong via observium observium@lists.observium.org *Sent:* Monday, December 4, 2023 3:35 PM *To:* Tony Guadagno via observium observium@lists.observium.org *Cc:* Adam Armstrong adama@observium.org *Subject:* [Observium] Re: units on error graphs?
The graph is showing a rate, so it's errors per second, or 44 milli-errors per second or something like 13 errors in the 5 minute poller period.
adam.
Tony Guadagno via observium wrote on 2023-12-04 19:46:
Just for reference, this is the “show interface” for the port in the graph…I understand that “show interface” shows a cumulative number while the graph is not….but as you can see, there have been 1241 input errors since the last reset…..that is no where near 44m? Hence my confusion thanks GigabitEthernet0/0 is up, line protocol is up Hardware is CN Gigabit Ethernet, address is 68ef.bd99.dca0 (bia 68ef.bd99.dca0 ) Description: lan Internet address is 1.1.1.1/24 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full Duplex, 1Gbps, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/13/11228 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 954000 bits/sec, 535 packets/sec 5 minute output rate 8346000 bits/sec, 885 packets/sec 3637522994 packets input, 1559853723 bytes, 0 no buffer Received 11917322 broadcasts (0 IP multicasts) 0 runts, 0 giants, 1 throttles 1241 input errors, 0 CRC, 0 frame, 1241 overrun, 0 ignored 0 watchdog, 177941 multicast, 0 pause input 322101698 packets output, 1529083260 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 403 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.com <mailto:tonyg@guadagnoconsulting.com> cid:image001.jpg@01D84DD6.FC9912E0 *From:* Tony Guadagno via observium <observium@lists.observium.org> <mailto:observium@lists.observium.org> *Sent:* Monday, December 4, 2023 2:12 PM *To:* Observium <observium@lists.observium.org> <mailto:observium@lists.observium.org> *Cc:* Tony Guadagno <tonyg@guadagno.org> <mailto:tonyg@guadagno.org> *Subject:* [Observium] units on error graphs? Hi, sorry if this is obvious, but it just occurred to me that I don’t understand this graph. This comes from an Ethernet port on a cisco router…. What are the units??for example the “last in errors/s” is 44.25m???? 44.24 million? That can’t be right. Thanks in advance Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.com <mailto:tonyg@guadagnoconsulting.com> cid:image001.jpg@01D84DD6.FC9912E0 _______________________________________________ observium mailing list --observium@lists.observium.org <mailto:observium@lists.observium.org> To unsubscribe send an email toobservium-leave@lists.observium.org <mailto:observium-leave@lists.observium.org>
observium mailing list -- observium@lists.observium.org To unsubscribe send an email to observium-leave@lists.observium.org
Yes, I can sympathize.
On a completely different topic, I wanted to ask you if you guys would consider putting out a yearly "roadmap" of your goals for Obserium. In particular, I am curious what features you would like to tackle in the coming year. To be clear, I am not looking for a committed time frame, just more generally, "we would like to add these features in 2024".
Is that something you would do?
Thanks
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Adam Armstrong via observium observium@lists.observium.org Sent: Monday, December 4, 2023 4:15 PM To: Tony Guadagno via observium observium@lists.observium.org Cc: Adam Armstrong adama@observium.org Subject: [Observium] Re: units on error graphs?
Quite a few people don't make the connection on that graph in particular!
Tony Guadagno via observium wrote on 2023-12-04 20:42:
Aahhh.... Milli-errors... LOL how could I have missed that...
Ok, that clears that up, thanks!
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Adam Armstrong via observium observium@lists.observium.orgmailto:observium@lists.observium.org Sent: Monday, December 4, 2023 3:35 PM To: Tony Guadagno via observium observium@lists.observium.orgmailto:observium@lists.observium.org Cc: Adam Armstrong adama@observium.orgmailto:adama@observium.org Subject: [Observium] Re: units on error graphs?
The graph is showing a rate, so it's errors per second, or 44 milli-errors per second or something like 13 errors in the 5 minute poller period.
adam.
Tony Guadagno via observium wrote on 2023-12-04 19:46:
Just for reference, this is the "show interface" for the port in the graph...I understand that "show interface" shows a cumulative number while the graph is not....but as you can see, there have been 1241 input errors since the last reset.....that is no where near 44m?
Hence my confusion thanks
GigabitEthernet0/0 is up, line protocol is up Hardware is CN Gigabit Ethernet, address is 68ef.bd99.dca0 (bia 68ef.bd99.dca0 ) Description: lan Internet address is 1.1.1.1/24 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full Duplex, 1Gbps, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/13/11228 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 954000 bits/sec, 535 packets/sec 5 minute output rate 8346000 bits/sec, 885 packets/sec 3637522994 packets input, 1559853723 bytes, 0 no buffer Received 11917322 broadcasts (0 IP multicasts) 0 runts, 0 giants, 1 throttles 1241 input errors, 0 CRC, 0 frame, 1241 overrun, 0 ignored 0 watchdog, 177941 multicast, 0 pause input 322101698 packets output, 1529083260 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 403 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
From: Tony Guadagno via observium observium@lists.observium.orgmailto:observium@lists.observium.org Sent: Monday, December 4, 2023 2:12 PM To: Observium observium@lists.observium.orgmailto:observium@lists.observium.org Cc: Tony Guadagno tonyg@guadagno.orgmailto:tonyg@guadagno.org Subject: [Observium] units on error graphs?
Hi, sorry if this is obvious, but it just occurred to me that I don't understand this graph. This comes from an Ethernet port on a cisco router.... [cid:image004.jpg@01DA26CD.B5840410]
What are the units??for example the "last in errors/s" is 44.25m???? 44.24 million? That can't be right.
Thanks in advance
Tony Guadagno O +1 585 577 1003 C +1 585 703 6700 E tonyg@guadagnoconsulting.commailto:tonyg@guadagnoconsulting.com [cid:image001.jpg@01D84DD6.FC9912E0]
_______________________________________________
observium mailing list -- observium@lists.observium.orgmailto:observium@lists.observium.org
To unsubscribe send an email to observium-leave@lists.observium.orgmailto:observium-leave@lists.observium.org
_______________________________________________
observium mailing list -- observium@lists.observium.orgmailto:observium@lists.observium.org
To unsubscribe send an email to observium-leave@lists.observium.orgmailto:observium-leave@lists.observium.org
participants (2)
-
Adam Armstrong -
Tony Guadagno