- observium - lists.observium.org

Average Packet Size on Cisco-Devices
by Chris 29 Aug '13

29 Aug '13

Hi There, I like seeing the Average Packet Size on Ports since 4361. But unfortunately I don't have data in graphs for all devices. It's working on: - 6500 VSS (Ten/Gig/Vlan/Po) (IOS 15.0) - ASA 55xx - Servers (Linux) - Riverbeds (Linux) - Cisco-WLAN-Controllers It's NOT working (empty graph) on: - 4500 (Ten/Gig/Po) - ASR1001 (Gig/Tu) (IOS 15.3S) - 7301 (Gig/Tu) (IOS 15.1M) - 28xx (Gig/Tu) (IOS 15.0M) - 18xx (Fa/Tu) (IOS 12.4T) Especially on our VPN-Rouers (73/28/ASR) this would be helpful. How can I debug some more things to get it working? Or how can I support you with information that you get it to work? Many thanks in advance, Chris

3 4

Re: [Observium] slow polling of Cisco 4500 VSS switches
by Adam Armstrong 29 Aug '13

29 Aug '13

Hmm. We don't even do anything with the poe information, are we still collecting it? Does the 4500 have any poe blades? Pretty scary walking the poe table would take so long. Adam. Bastiaan Topper <B.Topper(a)korton.nl> wrote: >Hi Adam, > >Thanks for your help. I found the problem. Nothing to do with the 4500 switches. Was the PoE polling option, this is not working efficiently, so for now I disabled it. > >Polling times dropped to few seconds now. > >Regards, > >Bastiaan > > > >-----Oorspronkelijk bericht----- >Van: Adam Armstrong [mailto:adama@memetic.org] >Verzonden: woensdag 28 augustus 2013 19:39 >Aan: Observium Network Observation System >Onderwerp: Re: [Observium] slow polling of Cisco 4500 VSS switches > >On 2013-08-28 17:28, Bastiaan Topper wrote: >> Hi Adam, >> >> The problem is that it is not only with VSS switches. The screenshot >> is off a switch without VSS (so a normal 4500 switch, but with many >> interfaces). I also have 6500 switches (and even a 6500 VSS), these >> don't have the problem, but have a lot less interfaces. >> The 4500 switches don't all run the same IOS version. The VSS switches >> have 2 version, the not VSS switch has an other supervisor and much >> older IOS. >> >> Thing I noticed is that the port polling collects all metrics for all >> interfaces for every interface it polls. For big switches, this is a >> lott of info each time it polls an interface. If I do a debug it show >> very long lists of collected metrics (output of all the snmpbulkwalk >> commands per interface), each time for all interfaces. Could it be >> that the problem is there somewhere, or am I interpreting the output >> wrong? > >It's not actually all that much information, and 250 ports isn't really a lot. > >The issue is almost certainly a bug with counter collection on the 4500. > >Cisco doesn't seem to bother giving many shits about bugs on "enterprise" kit, they only seem to fix issues on "service provider" >kit. > >This just further cements my view that the 4500 is a largely pointless device that people only buy when they've been tricked by Cisco's sales and marketing splurge. > >adam. > >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

3 4

RRD Graphs not showing
by Adam Summerfield 28 Aug '13

28 Aug '13

We have Observium installed on Ubuntu and it has been running for months... Just recently the RRD graphs have stopped appearing on the web pages I have upgraded to the latest version and it still is not working. The RRD files exist with the right permissions and the dates stamps are up to date. Can someone help please? Regards, Adam

4 9

slow polling of Cisco 4500 VSS switches
by Bastiaan Topper 28 Aug '13

28 Aug '13

Hi all, We have a very long poll time on some of the devices. We have a few Cisco 4500 switches with a lott of interfaces. For example a Cisco 4506 with 4x 48 ports linecard, the poll time for the device is: [cid:image001.png@01CEA3DD.702B0310] As you can see the poll time changed around 28/29 July. I disabled the device around 31 July, as you can see. We also have Cisco 4500 VSS setups with several hundreds of interfaces, these devices I disabled for now, because the poller couldn't keep up with it. Today I found some time to troubleshoot, and found the above statistics. Beside that a did a poll with debug on. It "hangs" very long on every interface of every device it polls. After looking into that, it seems that it collects all interfaces per metric it polls. I think that is the problem with devices with a big amount of interfaces, because it collects all statistics again for every interface. How can I fix this? Is this by design/Is this a bug? Or is it something in my setup? Regards, Bastiaan Topper Korton Group BV

4 7

Re: [Observium] How can i add app mysql to my observium
by Tom Laermans 28 Aug '13

28 Aug '13

Please read this email again, it will become clear... Sent from my mobile, please excuse brevity and spelling errors. ----- Reply message ----- From: "Robert Luczynski" <robert(a)byd.com.pl> To: "Observium Network Observation System" <observium(a)observium.org> Subject: [Observium] How can i add app mysql to my observium Date: Wed, Aug 28, 2013 17:29 i have xinetd config from scripts/observium_agent_xinetd documentation: http://www.observium.org/wiki/Unix_Agent How can i check xinetd config file is ok? telnet can connect to port 3662 my xinetd config: service observium_agent { type = UNLISTED port = 36602 socket_type = stream protocol = tcp wait = no user = root server = /usr/bin/observium_agent # configure the IP address(es) of your Observium server here: only_from = 127.0.0.1 # Don't be too verbose. Don't log every check. This might be # commented out for debugging. If this option is commented out # the default options will be used for this service. log_on_success = disable = no } On Aug 28, 2013, at 4:59 PM, Tom Laermans wrote: > Close, but no cigar yet ;-) > > Telnet didn't produce output, your xinetd config file is wrong; poller is not receiving your data. > > Tom > > On 08/28/2013 04:44 PM, Robert Luczynski wrote: >> I was running poller and dicovery script manually, rrd still doesn't have a rrd files... >> Cronjob setings is fine. >> >> >> >> >> On Aug 28, 2013, at 4:23 PM, Michael Sweikata wrote: >> >>> You have to run a poller and discovery after it's added to get those files generated. If your cron job is set up correctly and it will auto-poll devices every five minutes, just wait until the next cycle is complete, or run them manually. >>> >>> -----Original Message----- >>> From: observium [mailto:observium-bounces@observium.org] On Behalf Of Robert Luczynski >>> Sent: Wednesday, August 28, 2013 10:23 AM >>> To: Observium Network Observation System >>> Subject: Re: [Observium] How can i add app mysql to my observium >>> >>> Ok, i was missed mysql settings in observium panel. >>> I have app tab now, but graph is empty: (Error drawing graph) >>> >>> my rrd direcroty still does'n have a rrd files for mysql >>> >>> Any ideas? >>> >>> >>> On Aug 28, 2013, at 3:52 PM, Robert Luczynski wrote: >>> >>>> Hello >>>> >>>> I have a CentOS 6.4 >>>> >>>> >>>> I want to add app tab to my observium. I was folllow in aplication mysql: >>>> http://www.observium.org/wiki/Application/MySQL >>>> >>>> Unix agent is enabled: >>>> >>>> root@g [/opt/observium]# telnet localhost 36602Trying ::1... >>>> Connected to localhost. >>>> Escape character is '^]'. >>>> Connection closed by foreign host. >>>> >>>> mysql script work ok: >>>> >>>> root@g [/opt/observium]# /usr/lib/observium_agent/local/mysql >>>> <<<mysql>>> >>>> a0:5225549 >>>> a1:2200 >>>> a2:105805 >>>> a3:52579 >>>> a4:3774 >>>> a5:211779660 >>>> a6:1 >>>> a7:1 >>>> a8:-1 >>>> a9:-1 >>>> aa:8192 >>>> [...] >>>> ef:-1 >>>> eg:0 >>>> eh:1844224 >>>> ei:8388608 >>>> ej:3176 >>>> ek:890 >>>> >>>> puller info: >>>> >>>> ./poller.php all August 28, 2013, 9:49 - 1 devices polled in 0.739 secs >>>> MySQL: Cell[0/0s] Row[4/0s] Rows[30/0.01s] Column[0/0s] Update[22/0.01s] Insert[2/0.01s] Delete[0/0s] >>>> >>>> Thanks, Robert >>>> >>>> >>>> _______________________________________________ >>>> observium mailing list >>>> observium(a)observium.org >>>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >>> _______________________________________________ >>> observium mailing list >>> observium(a)observium.org >>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >>> >>> >>> _______________________________________________ >>> observium mailing list >>> observium(a)observium.org >>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >> _______________________________________________ >> observium mailing list >> observium(a)observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

missing Events Log in overview tab
by Micah Young 28 Aug '13

28 Aug '13

Hi Is anyone else having problems viewing the Events Log in the Overview tab? I have been writing custom code but the issue only comes up when I update past revision 4367. Let me know. Thanks! Mike Y. ARDEN A Global Company Celebrating over 48 years of making your life more comfortable! This message may contain confidential and/or privileged information. If you are not the addressee or authorized to receive this for the addressee, you must not use, copy, disclose, or take any action based on this message or any information herein. If you have received this message in error, please advise the sender immediately by reply e-mail and delete this message. This OUTBOUND E-mail and Document(s) has been scanned by an Antivirus Server.

1 1

Temperature Ipoman
by ColoCenter bv 28 Aug '13

28 Aug '13

Hi all, Since a couple of updates(not sure which) the temperature sensor on a Ipoman is not working/shown anymore. i had one working and was being polled fine, but now i noticed it is gone. Not sure with which update it disappeared. I have this in my logs: 2013-08-25 18:01:26 System Sensor Deleted: temperature ipoman 1 EMD Temperature Can this be fixed? Thanks -- Alexander Lantink ColoCenter bv http://www.colocenter.nl info(a)colocenter.nl 079-7113500sure w

4 12

Newbie ?s - map config
by McNett, Loren 28 Aug '13

28 Aug '13

Hello all, We’ve recently decided to move from Cacti, and tried Zenoss, and we’re now trying Observium. We’re *really* liking it. Device import went really well, and have been able to tune it to exactly what we need. I’m having issues with the map. The mapping of alerts is a pretty important feature for us, but I can’t seem to get it dialed in. You may certainly assume I know nothing about this mapping feature beyond the “Map Overview Settings” porton of the Configuration Options page. We’re a small campus so the scale of the map is not working out when we use the “US-565”. When the dots render they stack up. Is there a more ‘zoomed in’ option? How does one appropriately choose the ‘location’ data? If I can hop on google maps and put in a string and have it put a pin in the right building, is that string acceptable to use for the location field? I.E. “north hall library” gives me the correct location in google maps, does that mean I can use it for the location string? Since google maps has our building footprints drawn out, I’d prefer to use that layout, is it possible to switch it to that instead of the metro area shtick? Our map looks like this: [cid:image002.png@01CEA3E3.1FE973E0] Using the following in config.php //MAP data $config['frontpage']['map']['region'] = "US-565"; // See https://developers.google.com/chart/interactive/docs/gallery/geo$ $config['frontpage']['map']['resolution'] = "metros"; // Some region types such as US States (US-NY) require this to be changed t$ $config['frontpage']['map']['dotsize'] = 5; // Set the dotsize you want $config['frontpage']['map']['realworld'] = false; // Enable/Disable the realworld view (blue/green), if disabled default m$ Thanks! -Loren McNett

2 1

active/standby pairs (esp. FW)
by Rob VanHooren 28 Aug '13

28 Aug '13

some gear that's put up in pairs insists on having the same hostname/sysName, e.g. ASAs. even though their m0 are uniquely reachable, there's no currently obvious way to watch the standby, since even though its DNS is unique, addhost sees sysName and rejects it as being a duplicate. ideas? tks, R.

2 1

Incomplete device name (bug?)
by Richard Hartensveld 28 Aug '13

28 Aug '13

Hi all, If I add a device with a hostname of br0.abcdefg , it will show up nicely on the front page, however, when I add a device with a hostname of br0.abcdefgh (or longer), the device's name will be 'br0' on the front page under "device alerts" and "Recent Eventlog Entries". If you hoover over the device name, he popup screen wil display the correct device name. Could this be a bug, or am I doing something wrong ? Thanks. gr, Richard

2 1

Re: [Observium] OS Recognition
by Adam Armstrong 28 Aug '13

28 Aug '13

I am in the process of migrating this to the os script... :) Sander Steffann <sander(a)steffann.nl> wrote: >> Hi I just wanted to ask if observium is suppose to detect the flavour of linux or is this the correct behaviour? > >I think you want this part of the manual: >http://www.observium.org/wiki/Linux_Distribution_Detection > >Cheers :-) >Sander > >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] Mis-aligned data in memcached app
by Adam Armstrong 28 Aug '13

28 Aug '13

Seems like a good idea. Adam. Sander Steffann <sander(a)steffann.nl> wrote: >Hi, > >When debugging why my memcached graphs weren't working I discovered the following problem: > >SQL[SELECT * FROM `applications` WHERE `device_id` = '41' AND `app_type` = 'memcached'] >Including: applications/memcached.inc.phpmemcachedmemcached(127.0.0.1:11211) >SQL[SELECT app_id FROM `applications` WHERE `device_id` = '41' AND `app_instance` = '127.0.0.1:11211'] >RRD[cmd[update /opt/observium/rrd/v25.invalpool.nl/app-memcached-127.0.0.1_11211.rrd N:64:2.0.16-stable:0:0:5:1045:6202:8:0:0:14045:129043:6202:0:0:0:0:7184655:13093279] >stdout[ERROR: /opt/observium/rrd/v25.invalpool.nl/app-memcached-127.0.0.1_11211.rrd: conversion of '2.0.16-stable' to float not complete: tail '.16-stable'] >stderr[]] > >Obviously the data in the rrdtool update command were wrong. A version number shouldn't be in there... So I looked at what the memcached agent script was returning and how that was parsed by the poller memcached module. It turns out that there is a difference. The agent script returns a list of values in this order: > >accepting_conns, auth_cmds, auth_errors, bytes, bytes_read, bytes_written, cas_badval, cas_hits, cas_misses, cmd_flush, cmd_get, cmd_set, cmd_touch, conn_yields, connection_structures, curr_connections, curr_items, decr_hits, decr_misses, delete_hits, delete_misses, evicted_unfetched, evictions, expired_unfetched, get_hits, get_misses, hash_bytes, hash_is_expanding, hash_power_level, incr_hits, incr_misses, libevent, limit_maxbytes, listen_disabled_num, pid, pointer_size, reclaimed, reserved_fds, rusage_system, rusage_user, threads, time, total_connections, total_items, touch_hits, touch_misses, uptime, version > >The poller module parses them in this order: > >accepting_conns, auth_cmds, auth_errors, bytes, bytes_read, bytes_written, cas_badval, cas_hits, cas_misses, cmd_flush, cmd_get, cmd_set, conn_yields, connection_structures, curr_connections, curr_items, decr_hits, decr_misses, delete_hits, delete_misses, evictions, get_hits, get_misses, incr_hits, incr_misses, limit_maxbytes, listen_disabled_num, pid, pointer_size, rusage_system, rusage_user, threads, time, total_connections, total_items, uptime, version > >As you can see this breaks at cmd_touch: the agent sends a variable the poller doesn't expect, and as the data is sent value-only it has no way to determine that the imput is in different places than it expects... > >What I suggest to do is the following: >- update the agent so that key:value is sent instead of just value >- update the poller module so that it can parse key:value input >- make the poller module also accept the current value-only input as a fall-back > >If we agree that this is the way forward I'll send in a patch. > >Cheers, >Sander > >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

OS Recognition
by David Peall 28 Aug '13

28 Aug '13

Hi I just wanted to ask if observium is suppose to detect the flavour of linux or is this the correct behaviour? Linux ns1.coza.net.za 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 Hardware Generic x86 64-bit Operating System Linux 3.2.0-30-generic Regards -- David Peall

2 2

Mis-aligned data in memcached app
by Sander Steffann 28 Aug '13

28 Aug '13

Hi, When debugging why my memcached graphs weren't working I discovered the following problem: SQL[SELECT * FROM `applications` WHERE `device_id` = '41' AND `app_type` = 'memcached'] Including: applications/memcached.inc.phpmemcachedmemcached(127.0.0.1:11211) SQL[SELECT app_id FROM `applications` WHERE `device_id` = '41' AND `app_instance` = '127.0.0.1:11211'] RRD[cmd[update /opt/observium/rrd/v25.invalpool.nl/app-memcached-127.0.0.1_11211.rrd N:64:2.0.16-stable:0:0:5:1045:6202:8:0:0:14045:129043:6202:0:0:0:0:7184655:13093279] stdout[ERROR: /opt/observium/rrd/v25.invalpool.nl/app-memcached-127.0.0.1_11211.rrd: conversion of '2.0.16-stable' to float not complete: tail '.16-stable'] stderr[]] Obviously the data in the rrdtool update command were wrong. A version number shouldn't be in there... So I looked at what the memcached agent script was returning and how that was parsed by the poller memcached module. It turns out that there is a difference. The agent script returns a list of values in this order: accepting_conns, auth_cmds, auth_errors, bytes, bytes_read, bytes_written, cas_badval, cas_hits, cas_misses, cmd_flush, cmd_get, cmd_set, cmd_touch, conn_yields, connection_structures, curr_connections, curr_items, decr_hits, decr_misses, delete_hits, delete_misses, evicted_unfetched, evictions, expired_unfetched, get_hits, get_misses, hash_bytes, hash_is_expanding, hash_power_level, incr_hits, incr_misses, libevent, limit_maxbytes, listen_disabled_num, pid, pointer_size, reclaimed, reserved_fds, rusage_system, rusage_user, threads, time, total_connections, total_items, touch_hits, touch_misses, uptime, version The poller module parses them in this order: accepting_conns, auth_cmds, auth_errors, bytes, bytes_read, bytes_written, cas_badval, cas_hits, cas_misses, cmd_flush, cmd_get, cmd_set, conn_yields, connection_structures, curr_connections, curr_items, decr_hits, decr_misses, delete_hits, delete_misses, evictions, get_hits, get_misses, incr_hits, incr_misses, limit_maxbytes, listen_disabled_num, pid, pointer_size, rusage_system, rusage_user, threads, time, total_connections, total_items, uptime, version As you can see this breaks at cmd_touch: the agent sends a variable the poller doesn't expect, and as the data is sent value-only it has no way to determine that the imput is in different places than it expects... What I suggest to do is the following: - update the agent so that key:value is sent instead of just value - update the poller module so that it can parse key:value input - make the poller module also accept the current value-only input as a fall-back If we agree that this is the way forward I'll send in a patch. Cheers, Sander

1 0

No graphic image after the svn update
by waqar 27 Aug '13

27 Aug '13

hi all i just updated my observium using svn. after the update the graph image is not displaying at all.. i quickly revert back to my orignal version that is 4280 but still not graph image . i have deleted one of my device and then add it back but still no graph image.. ps: to be clear i m talking about no graph image.

1 1

Location debug : how ?
by Xavier Beaudouin 27 Aug '13

27 Aug '13

Hello, For some reason, on my observium at work, seems that location doesn't want to work. On device menun, still marked as "unkown". I tried to find is there is an issue with the location part, but on a setup at home, it is working. Location like Paris, FR / Belfort, FR still fail into unknown, so I wish to debug what happened, and how to fix it (maybe this an issue with my setup, but I cannot find where). Any hints about that? Regards, Xavier -- Xavier Beaudouin - Senior Network and System Administrator Infrastructure and network director Horizon Software - http://www.hsoftware.com/ 13 rue La Fayette - 75009 PARIS - France Phone: +33 (0)1 4260 9490 Fax: +33 (0)1 44 56 97 01

3 5

Horizontal Scalability
by Ciro Iriarte 23 Aug '13

23 Aug '13

Hi!, anybody considered scaling adding more servers instead of going to a bigger one?. Using something like Open Grid Scheduler for example. Currently I'm maxing out our server (2 x Xeon E5-2630, 16 cores) with 37500 ports, 548 devices cplanning:~ # uptime 13:19pm up 151 days 3:03, 2 users, load average: 43.37, 43.00, 42.60 Regards, CI.-

4 7

Apps incremental graph
by andres fariña 22 Aug '13

22 Aug '13

Hi All, Currently we are using app features to collect stats from our mobile platforms as troughput, for example Transactions Per Second. Is there an easy way to convert incremental RRD values to Transaction Per Second? Thanks for the help. Regards, Andres

1 0

how to support observium
by Chris 22 Aug '13

22 Aug '13

Hi there, I'm very new to observium and I set up a lot of devices now to be monitored. As I'm managing a big network running on EIGRP I'm missing some things I formerly built in cacti "per hand". I had always an eye on EIGRP queries, EIGRP Topo routes, EIGRP updates and such things. Is it possible to support you to bring in some new graphs into observium? unfortunately I'm not an php-coder but I've got long-term experience in networking and snmp. Nice features where also: - Usage of ISDN-Channels on voice-routers/Gateways (cisco) - Working GFX on MGE-UPS (we've got a big Powerware-Galaxy and want to see output power, battery runtime, and so on) - Working GFX on SmartUPS (older RM1400 - APS OS 3.7.3) (I#m missing output load) - More Sensors monitored of cisco 4500s. and I think I will have many more Ideas ;-) Greetings and many thanks for this great piece of software! Chris

1 0

Upgraded to latest SVN trunk
by James Bensley 21 Aug '13

21 Aug '13

I just wanted to say thanks to everyone on the Observium project. I updated last night a 2012 version of Observium to the very latest in SVN. Everything worked perfectly and I'm very happy with the results. Just wanted to say thank you for all your hard work, it isn't going unnoticed here! Kind regards, James.

1 0

Re: [Observium] New Install working except Graph/RRD
by Adam Armstrong 21 Aug '13

21 Aug '13

I run it as root. That's still the documented way. Adam. Paul Gear <observium(a)gear.dyndns.org> wrote: >On 08/21/2013 08:24 AM, Adam Armstrong wrote: >> The RRD directory doesn't actually need to be owned by www-data. >> >> If you want to run observium as a non-root user, chown it to that user. > >Is that the preferred method now? All of my installations still use >root since that was the documented method at the time I installed. > >Paul >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] New Install working except Graph/RRD
by Peter Casserly 21 Aug '13

21 Aug '13

I ran it as the root (sudo) and all is working now. Thank you for your quick responses. -Peter -----Original Message----- From: observium [mailto:observium-bounces@observium.org] On Behalf Of Adam Armstrong Sent: Tuesday, August 20, 2013 4:56 PM To: Observium Network Observation System Subject: Re: [Observium] New Install working except Graph/RRD Not root and not www-data, that's for sure. Who thought they knew better than the install guide, and managed to break it? The warnings are there for a reason :) adam. On 2013-08-20 21:36, Tom Laermans wrote: > And you are running the poller.php as which user? > > On 20/08/2013 21:34, Peter Casserly wrote: > > New to observium and I have it up and running on a new Ubuntu 13.04 > install. > > Everything seems to be working and polling the one device that I have > added. > > However…. > > It seems that none of the graphs are being generated. "Error Drawing > Graph" or "Draw Error" where the graphs should be. > > I reviewed the e-mail archives for similar issues but nothing seems to > fit. > > When I run the poller manually I see a few errors related to the RRD > directory and it looks like a permissions issue. > > ./poller.php -h all > > Observium v0.13.8.4312 > > Poller > > Starting polling run: > > fw.redacted.local 1 asa (cisco) > > Created directory : /opt/observium/rrd/fw. redacted.local > > ERROR: creating '/opt/observium/rrd/fw. redacted.local/status.rrd': No > such file or directory > > ERROR: creating '/opt/observium/rrd/fw.redacted.local /ping.rrd': No > such file or directory > > ERROR: creating '/opt/observium/rrd/fw.redacted.local/ping_snmp.rrd': > No such file or directory > > Module [ unix-agent ] disabled globally. > > Using SNMP Agent sysUpTime (10086692 seconds) > > ERROR: creating '/opt/observium/rrd/fw.redacted.local/uptime.rrd': No > such file or directory > > Uptime: 116 days, 17h 51m 32s > > The CHOWN (chown www-data.www-data graphs rrd )commands have been run > per the install documentation and show up as this: > > drwxr-xr-x 2 www-data www-data 4096 Aug 20 13:54 graphs > > drwxr-xr-x 2 www-data www-data 4096 Aug 20 13:54 rrd > > Thank you in advance for any assistance > > -Peter > > ------------------------- > > The information in this transmittal (including attachments, if any) is > privileged and confidential and is intended only for the recipient(s) > listed above. Any review, use, disclosure, distribution or copying of > this transmittal is prohibited except by or on behalf of the intended > recipient. If you have received this transmittal in error, please > notify me immediately by reply email and destroy all copies of the > transmittal. Thank you. > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium [1] > > > > Links: > ------ > [1] http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

3 2

rrdtool_info() redeclared issue
by Ray Parish 20 Aug '13

20 Aug '13

I am installing observium for the first time and getting a fatal error: [root@agsappl01 observium]# php -l includes/rrdtool.inc.php PHP Fatal error: Cannot redeclare rrdtool_info() in includes/rrdtool.inc.php on line 334 Fatal error: Cannot redeclare rrdtool_info() in includes/rrdtool.inc.php on line 334 Errors parsing includes/rrdtool.inc.php I am at svn revision 4313 To install, I had to comment out include_once($config['install_dir'] . "/includes/rrdtool.inc.php"); in includes/functions.php

2 2

Re: [Observium] Error Drawing Graph
by Peter Casserly 20 Aug '13

20 Aug '13

Sorry. I replied to the wrong e-mail. I only have one personality that I know of. From: observium [mailto:observium-bounces@observium.org] On Behalf Of Tom Laermans Sent: Tuesday, August 20, 2013 4:38 PM To: Observium Network Observation System Subject: Re: [Observium] Error Drawing Graph Do you have 2 separate identities, Peter? :> On 20/08/2013 22:29, Peter Casserly wrote: Screenshot attached of the Graph Errror(s) "It seems that none of the graphs are being generated. "Error Drawing Graph" or "Draw Error" where the graphs should be." There are placeholder images where the graphs should be. I don't believe is a value issue as I see traffic statistics in the "Ports" information pages but the ability to create the subdirectories and subsequent files defined in the original post. Created directory : /opt/observium/rrd/fw. redacted.local ERROR: creating '/opt/observium/rrd/fw. redacted.local/status.rrd': No such file or directory ERROR: creating '/opt/observium/rrd/fw.redacted.local /ping.rrd': No such file or directory ERROR: creating '/opt/observium/rrd/fw.redacted.local/ping_snmp.rrd': No such file or directory There are no files or folders created under the rrd and graphs directories. [cid:image001.png@01CE9DCB.451B1DD0] From: observium [mailto:observium-bounces@observium.org] On Behalf Of Michael Sweikata Sent: Tuesday, August 20, 2013 4:13 PM To: Observium Network Observation System Subject: Re: [Observium] Error Drawing Graph You'll have to be a bit more specific than that. Is it not drawing graphs at all? Are you getting NaN as values? Do you just not believe the numbers? Try doing a manual polling of the device through the console, and specify the -d flag for debugging, and see what comes back, with an optional -r to have it not update your values. From: observium [mailto:observium-bounces@observium.org] On Behalf Of Eliezer Sousa Sent: Tuesday, August 20, 2013 4:02 PM To: observium(a)observium.org<mailto:observium@observium.org> Subject: [Observium] Error Drawing Graph hello good afternoon everyone! some devices do not station generating the graph correctly. what causes this error in generating the graphics? [ass eliezer] ________________________________ The information in this transmittal (including attachments, if any) is privileged and confidential and is intended only for the recipient(s) listed above. Any review, use, disclosure, distribution or copying of this transmittal is prohibited except by or on behalf of the intended recipient. If you have received this transmittal in error, please notify me immediately by reply email and destroy all copies of the transmittal. Thank you. _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

New Install working except Graph/RRD
by Peter Casserly 20 Aug '13

20 Aug '13

New to observium and I have it up and running on a new Ubuntu 13.04 install. Everything seems to be working and polling the one device that I have added. However.... It seems that none of the graphs are being generated. "Error Drawing Graph" or "Draw Error" where the graphs should be. I reviewed the e-mail archives for similar issues but nothing seems to fit. When I run the poller manually I see a few errors related to the RRD directory and it looks like a permissions issue. ./poller.php -h all Observium v0.13.8.4312 Poller Starting polling run: fw.redacted.local 1 asa (cisco) Created directory : /opt/observium/rrd/fw. redacted.local ERROR: creating '/opt/observium/rrd/fw. redacted.local/status.rrd': No such file or directory ERROR: creating '/opt/observium/rrd/fw.redacted.local /ping.rrd': No such file or directory ERROR: creating '/opt/observium/rrd/fw.redacted.local/ping_snmp.rrd': No such file or directory Module [ unix-agent ] disabled globally. Using SNMP Agent sysUpTime (10086692 seconds) ERROR: creating '/opt/observium/rrd/fw.redacted.local/uptime.rrd': No such file or directory Uptime: 116 days, 17h 51m 32s The CHOWN (chown www-data.www-data graphs rrd )commands have been run per the install documentation and show up as this: drwxr-xr-x 2 www-data www-data 4096 Aug 20 13:54 graphs drwxr-xr-x 2 www-data www-data 4096 Aug 20 13:54 rrd Thank you in advance for any assistance -Peter ________________________________ The information in this transmittal (including attachments, if any) is privileged and confidential and is intended only for the recipient(s) listed above. Any review, use, disclosure, distribution or copying of this transmittal is prohibited except by or on behalf of the intended recipient. If you have received this transmittal in error, please notify me immediately by reply email and destroy all copies of the transmittal. Thank you.

3 2

Error Drawing Graph
by Eliezer Sousa 20 Aug '13

20 Aug '13

hello good afternoon everyone! some devices do not station generating the graph correctly. what causes this error in generating the graphics? ass eliezer

4 3

Host up/down polling
by James Bensley 20 Aug '13

20 Aug '13

Hi All, Sometimes I get host down notifications from Observium at the start of a 5 minute poll. Five minutes later I get a host up alert for the same host. I believe that sometimes a busy host will drop the 5 minute "probe" from Observium which is presumably a UDP SNMP packet. As soon as I get such a notification I check the host in question, it is usually up unless it really has gone down, just a bit busy perhaps. [1] Where is this initial checking of device up/down state happening in the code? I have been looking through include/polling and I can see various scripts for different device types. Is there a generic host up/down check that happens for all devices, I'd like to hack in a "if a device recorded as up seems down, wait and check again a couple more times, then mark as down". Cheers, James. [1] So that is a separate issue I need to tackle, ensuring there is no packet loss to hosts and ensuring they aren't too busy to respond. I don't wish to discuss that here though.

3 5

Lost sensors from PAN firewall
by Zafar Pravaiz 20 Aug '13

20 Aug '13

HI I am monitoring a pair of Palo Alto Firewall, recently i noticed one of the firewall not showing any traffic. I investigated and found there is not sensor showing in sensors list (screenshot attached). This happened recently any clue what happened and how to fix that? I don't want to delete and add the device again. Other PAN device show everything right. Thanks -- *Zafar Pravaiz *IT Senior Systems Engineer Information Technology Department AUS /> </span><span style='font-size:10.0pt;font-family:Times;mso-bidi-font-family: Tel +971 6 515 2164 Fax +971 6515 2112 American University of Sharjah PO Box 26666, Sharjah United Arab Emirates http://www.aus.edu <http://www.aus.edu/> zpravaiz(a)aus.edu <mailto:youremail@aus.edu>

1 1

Re: [Observium] Broken lines in disk usage chart
by Jordan TUCKER 20 Aug '13

20 Aug '13

Hi, Just to say that the problem with broken lines in disk usage chart is not new, I saw this problem monthes ago and I didn't succeeded to find how this is happening, but I didn't try the debug mode. I will come back to you shortly if I find something. It happens only on Windows servers and for a few of my windows servers, especially 2003 servers, they don't do any storage graph at all. Jordan T.

1 0

Login-Issue after Upgrade
by Patrick Kambach 20 Aug '13

20 Aug '13

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi all, after upgrading to 4305 the login failed; authlog tables shows "Logged In" and at the same timestamp "Authentication Failure". User / Password is correct. Br, Patrick - -- ConnectingBytes GmbH - "www.kambach.net" | In der Steele 35, 40599 Düsseldorf, Germany | Telefon: 0800 / 900 2580 - 1, Fax: 0800 / 900 2580 - 2 | Email: pkambach(a)kambach.net | Web: http://www.kambach.net | | Geschäftsführer: Patrick Kambach | Amtsgericht Düsseldorf, HRB 60009 | Ust-IdNr.: DE815028832, Steuernummer: 106/5736/0037 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.11 (MingW32) iEYEARECAAYFAlISTeUACgkQCIR+kawbQF24uQCgmB2aq1Ih6/flrSOOdt/HoA70 uCsAn1Rb7GKk6dHuK+AClFUKO16c/PlU =HfMf -----END PGP SIGNATURE-----

6 10

svn update broke Ubiquiti airos
by Zach Underwood 19 Aug '13

19 Aug '13

The ports are now marked for delete in observium version= 0.13.8.4309 dc_ap 49 airos Ports : DEBUG: SNMP Auth options = -v1 -c public /usr/bin/snmpwalk -v1 -c public -OQUs -m IF-MIB -M /opt/observium/mibs udp:dc_ap:161 ifDescr ifDescr.1 = lo ifDescr.2 = eth0 ifDescr.3 = eth1 ifDescr.4 = wifi0 ifDescr.5 = ath0 ifDescr.6 = ath1 ifDescr.7 = ath2 ifDescr.8 = eth0.100 ifDescr.9 = ath0.100 ifDescr.10 = eth0.1006 ifDescr.11 = ath0.1006 ifDescr.12 = br0 ifDescr.13 = br0.1006 ifDescr.14 = br0.100 -- Zach Underwood (RHCE,RHCSA,RHCT) My website <http://zachunderwood.me> My photes <http://zunder1990.openphoto.me>

1 0

Authentication system updates.
by Adam Armstrong 19 Aug '13

19 Aug '13

Evening Guys. We've committed some changes to the way the 'remember me' function of the authentication system works, removing a few pretty serious security issues with the old login system. We encourage everyone to upgrade to latest as soon as possible. You may need to restart your browser and/or clear cookies if you can't log in after the upgrade is done. adam.

1 0

svn broken
by Chris Stone 19 Aug '13

19 Aug '13

Looks like the svn setup is broken: Your request was unable to be processed com.cenqua.fisheye.rep.DbException - SVN Client exception fetching content: org.tigris.subversion.javahl.ClientException: svn: E175002: OPTIONS of '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php': 500 Internal Server Error (http://localhost) svn: E175002: OPTIONS request failed on '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php' - SVN Client exception fetching content: org.tigris.subversion.javahl.ClientException: svn: E175002: OPTIONS of '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php': 500 Internal Server Error (http://localhost) svn: E175002: OPTIONS request failed on '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php' - org.tigris.subversion.javahl.ClientException: svn: E175002: OPTIONS of '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php': 500 Internal Server Error (http://localhost) svn: E175002: OPTIONS request failed on '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php' - svn: E175002: OPTIONS of '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php': 500 Internal Server Error (http://localhost) svn: E175002: OPTIONS request failed on '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php' - svn: E175002: OPTIONS of '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php': 500 Internal Server Error (http://localhost) svn: E175002: OPTIONS request failed on '/svn/observer/trunk/html/pages/bill/infoboxes.inc.php' You are running release CR2.10.4 FE2.10.4 (20130403093648 2013-04-03), please report your release number when reporting bugs. Chris -- Chris Stone AxisInternet, Inc. www.axint.net

3 3

the resources in Observium MIB
by Eliezer Sousa 19 Aug '13

19 Aug '13

Hello, good afternoon everyone! I wonder how and when it is appropriate to use the resources in Observium MIB. ass eliezer

2 1

Re: [Observium] Broken lines in disk usage chart
by Michael F. Kisser 19 Aug '13

19 Aug '13

Hello, I have the same problem as well some servers on the network interface so big brakes in the lines. It started with this latest update. What's odd is the TX/RX white area does not match up top to bottom. So it's not like obervium could not reach the device. It's like it will process one but not the other at times TX/RX. Mike ---------------------------------------------------------------------- Message: 1 Date: Mon, 19 Aug 2013 11:35:25 +0000 From: Kristjan Hinn - PERH <Kristjan.Hinn(a)regionaalhaigla.ee> To: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] Broken lines in disk usage chart Message-ID: <FC8AD12ABE3FEC4E99A2D163779305AA06830B5B(a)MINERVA.regionaalhaigla.ee> Content-Type: text/plain; charset="us-ascii" Hi, I have almost the same problem with window 2008 R2 network traffic graphs. I have 4 identical servers and each of them have 3 network cards. One of the servers is drawing graphs perfectly but 3 servers have problem with one network card, other 2 network cards on the server are drawing perfectly. But this one network card is messing up summarized graphs also. I haven't found anything what might cause it[cid:image001.png@01CE9CE9.574202E0] Any advice or hint is highly appriciated BR, Kristjan -----Original Message----- From: observium [mailto:observium-bounces@observium.org] On Behalf Of Adam Armstrong Sent: Monday, August 19, 2013 6:18 AM To: Observium Network Observation System Subject: Re: [Observium] Broken lines in disk usage chart Hi, I doubt this has anything to do with us. You can see what data your device is reporting back by running the poller in debug mode: ./poller.php -h <hostname> -m storage -d -r You can see the data being returned via SNMP and what we interpret from it. adam. On 2013-08-19 00:54, Tom Henderson wrote: > What might be causing this disk usage chart to break up like this? > Looks like it started acting up after an upgrade a couple of weeks > ago. > > This is a windows 2008 r2 server and the disks are (mostly) iSCSI. It > seems to be the only server affected. > > Cheers > > Tom Henderson > > IT Manager | Pack & Company | 027 461 4403 | 09 929 2750 | > tom(a)pack.co.nz<mailto:tom@pack.co.nz> > > -- > > ------------------------- > > If you are not the intended recipient of this email, you must not > disclose, copy, or distribute any information contained in or attached > to it, or take any action/inaction based on it. Please contact us > immediately, and delete this email from your system. Any views or > opinions presented in this email are solely those of the author and > not of Pack & Company (NZ) Limited (the "Company"), however any > intellectual property contained in or attached to this email is the > property of the Company. Thank you. > _______________________________________________ > observium mailing list > observium(a)observium.org<mailto:observium@observium.org> > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

2 1

Broken lines in disk usage chart
by Tom Henderson 19 Aug '13

19 Aug '13

What might be causing this disk usage chart to break up like this? Looks like it started acting up after an upgrade a couple of weeks ago. This is a windows 2008 r2 server and the disks are (mostly) iSCSI. It seems to be the only server affected. [Image:Screen Shot 2013-08-19 at 10.59.18 AM.png] Cheers Tom Henderson IT Manager | Pack & Company | 027 461 4403 | 09 929 2750 | tom(a)pack.co.nz -- ---------------------------------------------------------------------------If you are not the intended recipient of this email, you must not disclose, copy, or distribute any information contained in or attached to it, or take any action/inaction based on it. Please contact us immediately, and delete this email from your system. Any views or opinions presented in this email are solely those of the author and not of Pack & Company (NZ) Limited (the "Company"), however any intellectual property contained in or attached to this email is the property of the Company. Thank you.

3 2

Cisco IPv6 BGP peers
by David Peall 19 Aug '13

19 Aug '13

I've upgraded one of my Cisco 7200 routers to c7200p-adventerprisek9-mz.152-4.S.bin to support IPv6 peer monitoring. I am how ever getting some funny things instead of the IPv6 Peers addresses and other details aren't working like updates: .C..0.......... iBGP ipv6.unicast .C............. eBGP ipv6.unicast There seems to be a newer file from cisco here updated 2001/2010 as apposed to the one included 2001/2003: ftp://ftp.cisco.com/pub/mibs/v2/CISCO-BGP4-MIB.my Otherwise if there is more trouble shooting or snmp walks I can provide that can help solve this please let me know. Thanks in advance -- David Peall

2 1

Ports page performance
by Adam Armstrong 19 Aug '13

19 Aug '13

Hi All, I've made some changes to how the ports page works to try to improve performance for people with very large installations. If you have issues with the /ports/ page speed, please test the speed of your install by loading /ports/, and trying with 1000 and 10000 ports page sizes. You need to refresh each page a few times to get an accurate page generation time. (the page generation time is at the bottom left) Then update your install with 'svn up' and run the same tests again. Please report back how much performance improvement you see, if any. I've also reduced some of the field sizes for the ports-state table which should reduce MySQL heap usage by about 20%. Thanks, adam.

1 0

Re: [Observium] Cisco IPv6 BGP peers
by Adam Armstrong 18 Aug '13

18 Aug '13

IPv6 support on Cisco kit appears and disappears at random. This is a Cisco problem. Adam. David Peall <david(a)dnservices.co.za> wrote: >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] Postgresql Application Monitor
by Adam Armstrong 18 Aug '13

18 Aug '13

Hi, The entire applications system was a quick hack I put together in a few hours. Once we have alerting working we intend to try to come up with a better way of doing it. Until then, I wouldn't recommend putting much time in to it. You might have more luck using a munin plugin, if one exists. We can pull munin plugins via the agent. Adam. David Peall <david(a)dnservices.co.za> wrote: >Hi > >I must first say I am really enjoying using Observium its a great tool. > >I've got a postgresql server with several databases in different name spaces and several pg clusters and was wondering if there is support for that. I couldn't see how to do it using the examples it seems to only support 1 database in 1 cluster per server. > >Regards >-- >David Peall >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Postgresql Application Monitor
by David Peall 18 Aug '13

18 Aug '13

Hi I must first say I am really enjoying using Observium its a great tool. I've got a postgresql server with several databases in different name spaces and several pg clusters and was wondering if there is support for that. I couldn't see how to do it using the examples it seems to only support 1 database in 1 cluster per server. Regards -- David Peall

1 0

Memory TAB empty on ESXi 5.1
by Philip Möller 16 Aug '13

16 Aug '13

Hi, I have several ESXi5.1 polled by my Observium. Everything is fine except that I have no graphs on the "Memory" TAB. I can see the Real Memory in the Disk Usage TAB. Is there a way to report all Real Memory Graphs in the Memory TAB instead oft he Storage TAB for better overview ? Best, Philip Möller

1 0

frontpage map disable
by Dennis Kruyt 14 Aug '13

14 Aug '13

Hi, How can I disable the worldmap? Before I used this setting but after I setup a new server from svn this doesn't work any more... $config['frontpage']['map']['show'] = false; // Enable/Disable the map view Met vriendelijke groet, Dennis Kruyt,- Technical Consultant [cid:image001.png@01CE98DB.95FD2C60] Capitar IT Group BV Amsterdamseweg 34 B 6712 GJ Ede KvK: 52455785 T: +31 88 6950000 M: +31 6 43534490 W: www.capitar.com<http://www.capitar.com/> Deze e-mail is vertrouwelijk en uitsluitend bestemd voor de geadresseerde. De algemene voorwaarden<http://www.capitar.com/index.php/nl/algemene-voorwaarden> van Capitar IT Group BV zijn van toepassing op offertes en prijsopgaves. Op deze email is de disclaimer van toepassing die te vinden is op webpagina "www.capitar.com/nl/disclaimer<http://www.capitar.com/nl/disclaimer>

3 2

User levels
by Benjamin Abadie 14 Aug '13

14 Aug '13

Hi, Are user levels implemented yet ? I know we can assign a level to a specific user when creating it, but is there a way to assign different rights to levels ? I see *_perms tables in DB, how should they be populated ? Regards, Benjamin Abadie

3 3

Not detecting ATM Interfaces
by Colin Anderson 12 Aug '13

12 Aug '13

Hi, We have a Cisco 7206 router with an OC3 ATM Port Adapter (PA-A3-OC3SMI=). The Ethernet and Serial interfaces show up in Observium, but it does not list the ATM interfaces. Is there anything we can do to get this to work? We have several hundred ATM sub interfaces on this card that I need to be able to monitor. Any help is much appreciated! Thanks, Colin Anderson Senior Network Engineer T3 Communications 239-333-3027 Direct/Cell c.anderson(a)t3com.net<mailto:c.anderson@t3com.net> http://www.t3com.com<http://www.t3com.com/>

2 3

Observium stops working after r4260
by Laurens Vets 12 Aug '13

12 Aug '13

Hello, This morning, I upgraded my r4200 installation to the latest release (r4280). After this update, "./discovery -h none" would not output anything when run. This also means that the DB was not updated to 080.sql. After a lot of troubleshooting I could not determine what went wrong and went back to r4200. Observium worked again after this. I then started upgrading per 10 releases and after r4260, Observium stops working (no output when running "./discovery -h none"). So, for me, r4260 is the last Observium release that works and r4261 is the first one that does not work anymore... This is on CentOS 6.4 with all updates installed: [root@bak observium]# ./scripts/os Linux|2.6.32-358.14.1.el6.x86_64|amd64|CentOS|6.4 [root@bak observium]# Is anybody else experiencing the same issue? Any idea what might be causing this? What additional things can I do to help solve this? -Laurens

3 5

Re: [Observium] DMI
by Tom Laermans 11 Aug '13

11 Aug '13

That's all crap added by someone who felt it necessary to add checking kunk to scripts, now apparently it doesn't work. I'll keep it in mind, still on vacation atm :) Sent from my mobile, please excuse brevity and spelling errors. ----- Reply message ----- From: "pechspilz" <pechspilz(a)o11.net> To: "Observium Network Observation System" <observium(a)observium.org> Subject: [Observium] DMI Date: Sun, Aug 11, 2013 13:02 Hi Tom, I've applied some small fixes to the hddtemp and dmi scripts so they run under Ubuntu: dmi (line 12): if [[ `head -c1 /dev/mem 2>&1 | awk '{print $1}'` != 'head:' ]] --> double brackets hddtemp (line 10): nc=`which nc.traditional` --> Since nc has been replaced. Probably, it would be best to check if nc.traditional exists and if yes, us it instead of nc. Cheers, John On 10.8.2013 10:45, Tom Laermans wrote: > Hi, > > We currently use the serial number and the hardware model in the > device info. > > Sent from my mobile, please excuse brevity and spelling errors. > > ----- Reply message ----- > From: "pechspilz" <pechspilz(a)o11.net> > To: <observium(a)observium.org> > Subject: [Observium] DMI > Date: Sat, Aug 10, 2013 08:39 > > Hi, > > does anyone know if the results from the dmi agent script is available > > in Observium? So far I've been unable to locate it. > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] DMI
by Tom Laermans 11 Aug '13

11 Aug '13

That's all crap added by someone who felt it necessary to add checking kunk to scripts, now apparently it doesn't work. I'll keep it in mind, still on vacation atm :) Sent from my mobile, please excuse brevity and spelling errors. ----- Reply message ----- From: "pechspilz" <pechspilz(a)o11.net> To: "Observium Network Observation System" <observium(a)observium.org> Subject: [Observium] DMI Date: Sun, Aug 11, 2013 13:02 Hi Tom, I've applied some small fixes to the hddtemp and dmi scripts so they run under Ubuntu: dmi (line 12): if [[ `head -c1 /dev/mem 2>&1 | awk '{print $1}'` != 'head:' ]] --> double brackets hddtemp (line 10): nc=`which nc.traditional` --> Since nc has been replaced. Probably, it would be best to check if nc.traditional exists and if yes, us it instead of nc. Cheers, John On 10.8.2013 10:45, Tom Laermans wrote: > Hi, > > We currently use the serial number and the hardware model in the > device info. > > Sent from my mobile, please excuse brevity and spelling errors. > > ----- Reply message ----- > From: "pechspilz" <pechspilz(a)o11.net> > To: <observium(a)observium.org> > Subject: [Observium] DMI > Date: Sat, Aug 10, 2013 08:39 > > Hi, > > does anyone know if the results from the dmi agent script is available > > in Observium? So far I've been unable to locate it. > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] DMI
by Tom Laermans 11 Aug '13

11 Aug '13

Hi, We currently use the serial number and the hardware model in the device info. Sent from my mobile, please excuse brevity and spelling errors. ----- Reply message ----- From: "pechspilz" <pechspilz(a)o11.net> To: <observium(a)observium.org> Subject: [Observium] DMI Date: Sat, Aug 10, 2013 08:39 Hi, does anyone know if the results from the dmi agent script is available in Observium? So far I've been unable to locate it. _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

2 1

Re: [Observium] DMI
by Tom Laermans 11 Aug '13

11 Aug '13

Then why does the script exist, you think? Sent from my mobile, please excuse brevity and spelling errors. ----- Reply message ----- From: "Adam Armstrong" <adama(a)memetic.org> To: "Observium Network Observation System" <observium(a)observium.org> Subject: [Observium] DMI Date: Sat, Aug 10, 2013 15:38 It is not at the moment. Adam. pechspilz <pechspilz(a)o11.net> wrote: >Hi, > >does anyone know if the results from the dmi agent script is available >in Observium? So far I've been unable to locate it. > >_______________________________________________ >observium mailing list >observium(a)observium.org >http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0