- observium - lists.observium.org

Disable alert reminders being sent
by Oliver Baker 26 Oct '16

26 Oct '16

Hi there, I'd like to set up Observium's alerts so that we only receive 1 alert email, and no more are sent even if the alert condition persists. I've set the following in config.php but I am not sure if it will give the desired effect: $config['alerts']['interval'] = 0; Is this the correct way to achieve this? Are there any further steps that need to be taken? Many thanks Oliver Baker

4 4

Administration delegation
by Youssef BENGELLOUN - ZAHR 26 Oct '16

26 Oct '16

1 0

Re: [Observium] new icons
by Serghei Golipad 26 Oct '16

26 Oct '16

I’ve made no changes what so ever and it’s been working before, one of the updates screwed this up. From: observium <observium-bounces(a)observium.org> on behalf of "Vater, Wolfgang" <wolfgang.vater(a)de.unisys.com> Reply-To: Observium Network Observation System <observium(a)observium.org> Date: Wednesday, 26 October 2016 at 12:19 To: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] new icons Did you enable fdbcount in the ports polling section on the modules tab in the device config? From: observium [mailto:observium-bounces@observium.org] On Behalf Of Serghei Golipad Sent: Wednesday, October 26, 2016 13:05 To: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] new icons Mine has disappeared: [cid:image001.png@01D22F85.5F365DC0] From: observium [mailto:observium-bounces@observium.org] On Behalf Of Vater, Wolfgang Sent: 26 October 2016 12:01 To: Observium Network Observation System Subject: Re: [Observium] new icons Hmm, I have a FDB table on my ports [cid:image002.png@01D22F85.5F365DC0] From: observium [mailto:observium-bounces@observium.org] On Behalf Of Serghei Golipad Sent: Wednesday, October 26, 2016 12:56 To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Subject: Re: [Observium] new icons Yes, but where did FDB table go on per port basis? ☹ No one answered so far. From: observium [mailto:observium-bounces@observium.org] On Behalf Of Anders Alavik Sent: 26 October 2016 11:49 To: Observium Network Observation System Subject: Re: [Observium] new icons +1 Best Med vänlig hälsning, Anders Alavik BogalNet AB 0738-305435 26 okt. 2016 kl. 12:44 skrev Vater, Wolfgang <wolfgang.vater(a)de.unisys.com<mailto:wolfgang.vater@de.unisys.com>>: Just upgraded, love the new icons! Wolfgang _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium PLEASE CONSIDER THE ENVIRONMENT BEFORE PRINTING THIS EMAIL. CDW Limited is a Company registered in England and Wales. This email is sent for and on behalf of CDW Finance Holdings Limited. CDW Finance Holdings Limited is the UK holding company for CDW Limited trading as CDW. The registered office for CDW Finance Holdings Limited (Company Number 05872067) and its UK group undertakings is 10 Fleet Place, London, EC4M 7RB. VAT Registration 902 1949 39. Confidentiality: This e-mail contains proprietary information, some or all of which may be confidential and/or legally privileged. It is for the intended recipient only. If an addressing or transmission error has misdirected this e-mail, please notify the author by replying to this e-mail and then delete the original. If you are not the intended recipient you may not use, disclose, distribute, copy, print or rely on any information contained in this e-mail. You must not inform any other person other than CDW or the sender of its existence. For more information about CDW please visit www.uk.cdw.com<http://www.uk.cdw.com>

1 0

new icons
by Vater, Wolfgang 26 Oct '16

26 Oct '16

Just upgraded, love the new icons! Wolfgang

3 5

Map No change in frontpage
by San Rollheiser 26 Oct '16

26 Oct '16

Hi i have problems with the map. Change via web and via file in defualt.inc.php But never change... always show: Leaflet | Map data © OpenStreetMap contributors, © CARTO My observium is the Stable Version Licensed and use a Old BK in my new installation. Any idea? BR Santiago

2 3

change to html/includes/authenticate.inc.php broke apache's AuthBasicFake . [SEC=UNCLASSIFIED]
by Peter.Hine＠familycourt.gov.au 26 Oct '16

26 Oct '16

Adam, First up, this happened a long time ago. It's just taken till now to find why it broke (cause i have free time, i'm testing 0.16.9.8118 and found the error again) The problem lies in line 200 of html/includes/authenticate.inc.php (v0.16.9.8118) if (!$_SESSION['authenticated'] && (authenticate($_SESSION['username'], $auth_password) || // login/password in older versions, "$auth_password" was "$_SESSION['password']". by replacing "$auth_password" with "$_SESSION['password']"., AuthBasicFake works again. I can't see where "$auth_password" is initialized but it's not my code so i'll not assume too much more than that. thanks Peter Hine Senior Technical Support Engineer (Servers) Corporate Services | Federal Court of Australia ********************************************************************** The information contained in this e-mail (including any attachments) is for the exclusive use of the addressee. If you are not the intended recipient please notify the sender immediately and delete this e-mail. It is noted that legal privilege is not waived because you have read this e-mail. **********************************************************************

2 2

JpGraph install
by Michaël MORELIERE 25 Oct '16

25 Oct '16

Hi, I try to install jpgraph. I follow the instruction : No Jpgraph installed *Jpgraph has been removed from the Observium repositories and must now be installed separately* * Please download from http://jpgraph.net/download/ and unpack to html/includes/jpgraph. * Remove the theme definition from the bottom of html/includes/jpgraph/src/jpg-config.inc.php when I refresh the page i get a jpgraph error 25121. Anyone can help me on this ? Regards -- Michaël MORELIERE

4 8

Potential RRD Cache bug with Unix Agent / Applications
by Andy Lemin 25 Oct '16

25 Oct '16

Hi, Not sure if this is a bug, or a cannot fix, but; If rrdcached is running and "$config['rrdcached'] = "unix:/var/run/rrdcached.sock" is configured in config.php, the graphs for the Unix Agent do not work. I can understand why Smokeping does not work if it does not know how to read and write from the unix socket (so we created a link to SmokePing in the Globe menu). But I cannot think why the Observium UNIX Agent does not work, as that is a part of Observium, and the rest of observium works with rrdcached. I can only guess that the UNIX Agent poller is not writing to the UNIX socket and is still trying to write to /opt/observium/rrd/, however when I disable RRDCache and remove the rrdcached line from config.php, all the old data appears. This makes me think that the UNIX Agent poller is writting to the socket correctly, and it is just Observium itself that is failing to revert to reading from the UNIX socket for Applications etc. Cheers, Andy.

1 0

Ports sensors missing for Brocade FCX 648
by Youssef BENGELLOUN - ZAHR 25 Oct '16

25 Oct '16

1 0

Update Issue
by Josh Hopper 24 Oct '16

24 Oct '16

Hello, I updated my Ubuntu VM from version 14.04 to 16.04 (LTS). After doing so PHP was not working as Observium's GUI wouldn't load. I updated PHP and PHP MYSQLI accordingly. I'm on v7 now. I was able to get to the login screen and login, however, after, I get a blank window. [image: Inline image 1] Code behind it looks odd. <!DOCTYPE html> <html lang="en"> <head> <base href="http://svr-observium.noc.dynamicinfastructure.com/" /> <meta http-equiv="content-type" content="text/html; charset=utf-8" /> <meta http-equiv="X-UA-Compatible" content="IE=edge,chrome=1" />  <link href="css/observium.css <http://svr-observium.noc.dynamicinfastructure.com/css/observium.css>" rel=" stylesheet" type="text/css" /> <link href="css/jquery.qtip.min.css <http://svr-observium.noc.dynamicinfastructure.com/css/jquery.qtip.min.css>" rel="stylesheet" type="text/css" /> <link href="css/svg_png.css <http://svr-observium.noc.dynamicinfastructure.com/css/svg_png.css>" rel=" stylesheet" type="text/css" /> <link href="css/flags.css <http://svr-observium.noc.dynamicinfastructure.com/css/flags.css>" rel=" stylesheet" type="text/css" /> <link href="css/c3.min.css <http://svr-observium.noc.dynamicinfastructure.com/css/c3.min.css>" rel=" stylesheet" type="text/css" />   <script type="text/javascript" src="js/jquery.min.js <http://svr-observium.noc.dynamicinfastructure.com/js/jquery.min.js>"> </script> <script type="text/javascript" src="js/bootstrap.min.js <http://svr-observium.noc.dynamicinfastructure.com/js/bootstrap.min.js>"> </script> <script type="text/javascript" src="js/observium.js <http://svr-observium.noc.dynamicinfastructure.com/js/observium.js>"> </script> <script type="text/javascript" src="js/d3.min.js <http://svr-observium.noc.dynamicinfastructure.com/js/d3.min.js>"></script> <script type="text/javascript" src="js/c3.min.js <http://svr-observium.noc.dynamicinfastructure.com/js/c3.min.js>"></script>   <meta http-equiv="refresh" content="300" /> <title>Observium</title> <link rel="shortcut icon" href="images/observium-icon.png <http://svr-observium.noc.dynamicinfastructure.com/images/observium-icon.png>" /> Like, where is the rest? :) It seems Observium is still running as I can run a discovery and poller from the command line and it runs fine. I did an svn update too to be on the latest version of Observium. Thanks for the help! -- JOSHUA HOPPER NETWORK ENGINEER 1-828-558-1403 Joshua.Hopper(a)broadplex.net www.broadplex.net

3 6

Re: [Observium] Transceiver alerts checkers
by Henrik Cednert (Filmlance) 24 Oct '16

24 Oct '16

-- Henrik Cednert cto | compositor Filmlance International | www.filmlance.se mobile [ + 46 (0)704 71 89 54 ] skype [ cednert ] On 2016-10-24, 16:48, "observium on behalf of Youssef BENGELLOUN - ZAHR" <observium-bounces(a)observium.org on behalf of ybzahr(a)prodware.fr> wrote: Dear Observium Community, I’m trying to configure alerts checkers for our transceivers sensors. Checkers have to be as generic as possible as we run, probably like you, all kinds of gear (routers / switchs / servers / etc.). I have created the following checkers : It seems something is wrong with the top 3 checkers. Either I’m too generic and sensor_values I have don’t apply or sensor_class I’m using is not the right one !?! Anyhow, a little help would be appreciated :-) Thank you. Youssef BENGELLOUN - ZAHR - Consultant Expert Prodware France T : +33 979 999 000 - F : +33 988 814 001 - ybzahr(a)prodware.fr ________________________________________ Web : prodware.fr <http://www.prodware.fr> <http://twitter.com/Prodware/> <http://www.facebook.com/Prodware/> <https://www.linkedin.com/company/prodwarefrance> <https://www.youtube.com/c/ProdwareFrance> <http://www.viadeo.com/fr/company/prodware> <http://www.prodware.fr/social-network/>

1 1

Temperature Sensor Compatibility
by Cameron Murray 23 Oct '16

23 Oct '16

Guys, Can anyone recommend a small IP based temperature/humidity sensor unit to monitor remote racks? I've checked http://www.observium.org/docs/supported_devices/ but would like firsthand experience recommendations please. Regards, Cameron

8 8

running observium on freebsd
by Simon Smith 22 Oct '16

22 Oct '16

Hi All, this is a random question, has anyone got observium running correctly on freebsd? managed to get it all setup and running, panels fine, add devices fine, poll device manually, etc only issue I’m having is i can’t get the cronjob working for every 5mins? i can see from the cron log in /var/log its running the poller correctly Oct 18 04:05:00 observium /usr/sbin/cron[49554]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) Oct 18 04:10:00 observium /usr/sbin/cron[50385]: (root) CMD (/usr/libexec/atrun) Oct 18 04:10:00 observium /usr/sbin/cron[50387]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) Oct 18 04:15:00 observium /usr/sbin/cron[51227]: (root) CMD (/usr/libexec/atrun) Oct 18 04:15:00 observium /usr/sbin/cron[51228]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) Oct 18 04:20:00 observium /usr/sbin/cron[52076]: (root) CMD (/usr/libexec/atrun) Oct 18 04:20:00 observium /usr/sbin/cron[52079]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) Oct 18 04:25:00 observium /usr/sbin/cron[52917]: (root) CMD (/usr/libexec/atrun) Oct 18 04:25:00 observium /usr/sbin/cron[52918]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) Oct 18 04:30:00 observium /usr/sbin/cron[53752]: (root) CMD (/usr/libexec/atrun) Oct 18 04:30:00 observium /usr/sbin/cron[53753]: (root) CMD (/opt/observium/poller-wrapper.py 2 >> /dev/null) however no data gets inserted into the db, but if i run the command manually as root, it inserts stuff fine? the only thing i can think of is the php is running apache which then runs as www not root would this have an issue maybe? regards Simon

4 7

quering raid status on adaptec, lsi, 3w cli
by Sebastian Klute 21 Oct '16

21 Oct '16

Is there a way to get the current raid status of the common controllers? We are using several LSI 9xxxx series some adaptec 6405 8405 and from time to time 3ware controllers. I've noticed that there is a discovery module for raid but if enabled nothing happens. Looking into some codes even through the unix agent there is only cfggen but no support for megacli like stuff. Any workarounds? Other methods to get the status? Best regards Sebastian Klute -- Accelerated IT Services GmbH Kruppstraße 105 - 60388 Frankfurt - Germany sk(a)accelerated.de - http://www.accelerated.de/ Phone: +49 69 - 900 180 41 - Fax: +49 69 - 900 180 90 HRB: 60665 - Amtsgericht Ludwigshafen - VatID: DE253684415 Managing Directors: Nicolaj Kamensek & Ole Krieger

2 1

Re: [Observium] Carel / pCo Discovery
by Robert Williams 21 Oct '16

21 Oct '16

Hi, Thanks for that, I’ve selected one host and disabled the MIB here (only): I have left the Sensors module (and all others) enabled and then re-run the discovery – output attached. FWIW – in the non-debug mode, it still mentions UNCDZ (twice actually): ##### Module Start: sensors ##### ENTITY-SENSOR-MIB o UNCDZ-MIB temp-amb [] temp-ext [] temp-mand [] temp-circ [] temp-ac [] umid-amb [] hdiff [] hu-diff [.] hset [.] hset-sm [.] t-set-sm [] t-set-c-sm [] t-cw-dh [] t-set-cw [] t-rc-es [] t-rc-est [] t-set-lm [.] hu-set [] hu-set-sm [] o UNCDZ-MIB t-set [] t-diff [] t-set-c [] <snip>... Let me know if I’m missing something stupid here – cheers! Robert Williams Custodian Data Centre Email: Robert(a)CustodianDC.com http://www.CustodianDC.com

2 2

Checker/Alert Notification Issue
by Pico Leto 21 Oct '16

21 Oct '16

Hi, I have a BGP alert checker / notification that doesn't seem to be working like it used to. The check applies to only about 140 peers. It's the standard test that the documentation provides. Enitity/Device match are * and the test is: bgpPeerAdminStatus equals start bgpPeerState notequals established I've noticed recently that I have only been getting some device notifications while the others don't even make it to the mail queue, however observium says that a notification was sent. I've tried deleting the alert checker and recreating it with the same results. Created a fake BGP peer that is in Active mode right now and ran the debugger on it (also a debug on a current working peer) *(no notification)* $ ./test_alert.php -a 128226 -dd DEBUG! Load class 'Console_Color2' from '/opt/observium/libs/pear/Console/Color2.php': OK SQL[SELECT `attrib_value` FROM `observium_attribs` WHERE `attrib_type` = 'dbSchema';] ROWS[1] SQL RUNTIME[0.00035691s] SQL[SELECT @@SESSION.sql_mode;] ROWS[1] SQL RUNTIME[0.00018501s] SQL[SELECT `attrib_value` FROM `observium_attribs` WHERE `attrib_type` = 'current_rev';] ROWS[1] SQL RUNTIME[0.00025105s] SQL[SELECT * FROM `config`] ROWS[0] SQL RUNTIME[0.00022912s] Load class 'Net_IPv6' from '/opt/observium/libs/pear/Net/IPv6.php': OK Observium 0.16.10.8161 Test Alert Notification CMD[/opt/observium/scripts/distro] CMD EXITCODE[0] CMD RUNTIME[0.0168s] STDOUT[ Linux|3.10.0-327.36.1.el7.x86_64|amd64|CentOS|7.2.1511 ] CMD[/usr/bin/env python --version 2>&1] CMD EXITCODE[0] CMD RUNTIME[0.0047s] STDOUT[ Python 2.7.5 ] SQL[SELECT version();] ROWS[1] SQL RUNTIME[0.00029111s] CMD[/usr/bin/snmpget --version 2>&1] CMD EXITCODE[0] CMD RUNTIME[0.0087s] STDOUT[ NET-SNMP version: 5.7.2 ] CMD[/usr/bin/rrdtool --version | head -n1] CMD EXITCODE[0] CMD RUNTIME[0.0086s] STDOUT[ RRDtool 1.4.8 Copyright 1997-2013 by Tobias Oetiker <tobi(a)oetiker.ch> ] CMD[/usr/bin/rrdcached -h | head -n1] CMD EXITCODE[0] CMD RUNTIME[0.0082s] STDOUT[ RRDCacheD 1.4.8 ] CMD[/usr/bin/env apache2 -v | awk '/Server version:/ {print $3}'] CMD EXITCODE[0] CMD RUNTIME[0.004s] STDOUT[ ] CMD[/usr/bin/env httpd -v | awk '/Server version:/ {print $3}'] CMD EXITCODE[0] CMD RUNTIME[0.0346s] STDOUT[ Apache/2.4.6 ] CMD[date "+%:z"] CMD EXITCODE[0] CMD RUNTIME[0.0032s] STDOUT[ -07:00 ] SQL[SELECT TIMEDIFF(NOW(), UTC_TIMESTAMP);] ROWS[1] SQL RUNTIME[0.00026107s] SQL[SELECT @@SESSION.sql_mode;] ROWS[1] SQL RUNTIME[0.00019383s] SQL[SHOW VARIABLES LIKE 'character_set_connection'] ROWS[1] SQL RUNTIME[0.00065804s] ##### Software versions ##### o OS Linux 3.10.0-327.36.1.el7.x86_64 [amd64] (CentOS 7.2.1511) o Apache 2.4.6 o PHP 5.4.16 o Python 2.7.5 o MySQL 5.5.50-MariaDB (extension: mysqli 5.5.50-MariaDB) o SNMP NET-SNMP 5.7.2 o RRDtool 1.4.8 (rrdcached 1.4.8: unix:/var/run/rrdcached/rrdcached.sock) ##### MySQL mode ##### o MySQL ##### Charset info ##### o PHP UTF-8 o MySQL utf8 ##### Timezones info ##### o Date Thursday, 20-Oct-16 21:40:54 PDT o PHP -07:00 o MySQL -07:00 SQL[SELECT * FROM `alert_tests` WHERE 1] ROWS[32] SQL RUNTIME[0.00031996s] Cached 32 alert rules. SQL[SELECT * FROM `alert_assoc`] ROWS[32] SQL RUNTIME[0.00021911s] SQL[SELECT * FROM `alert_table` WHERE `alert_table_id` = '128226'] ROWS[1] SQL RUNTIME[0.00021100s] SQL[SELECT * FROM `devices` WHERE `device_id` = '77'] ROWS[1] SQL RUNTIME[0.00027394s] SQL[SELECT * FROM `device_graphs` WHERE `device_id` = '77'] ROWS[38] SQL RUNTIME[0.00034308s] SQL[SELECT * FROM `bgpPeers` LEFT JOIN `bgpPeers-state` USING (`bgpPeer_id`) WHERE `bgpPeers`.`bgpPeer_id` = '3268'] ROWS[1] SQL RUNTIME[0.00026608s] > $graphtype - /opt/observium/includes/alerts.inc.php:1170 /opt/observium/html/includes/graphs/graph.inc.php:33 ======================================================== array( [0] => string(11) "bgp_updates" [type] => string(3) "bgp" [1] => string(3) "bgp" [subtype] => string(7) "updates" [2] => string(7) "updates" ) SQL[SELECT * FROM `bgpPeers` WHERE `bgpPeer_id` = '3268'] ROWS[1] SQL RUNTIME[0.00020003s] RRD PIPE OPEN[TRUE] RRD PIPE CLOSE[TRUE] RRD PIPE STDOUT[ OK u:0.03 s:0.01 r:0.03 ] RRD CMD[graph --daemon unix:/var/run/rrdcached/rrdcached.sock /tmp/1utnX5E8LqmthZw7.png -g -Y --lower-limit 0 --alt-autoscale-max --start 1476852054 --end 1477024854 --width 400 --height 150 -c BACK#EEEEEE00 -c SHADEA#EEEEEE00 -c SHADEB#EEEEEE00 -c FONT#000000 -c CANVAS#FFFFFF00 -c GRID#a5a5a5 -c MGRID#FF9999 -c FRAME#5e5e5e -c ARROW#5e5e5e -R normal --font LEGEND:8:'DroidSansMono,DejaVuSansMono' --font AXIS:7:'DroidSansMono,DejaVuSansMono' --font-render-mode normal -E COMMENT:'Updates Last Avg Max \n' DEF:out=/opt/observium/rrd/asr1-sv2/bgp-100.65.0.49.rrd:bgpPeerOutUpdates:AVERAGE DEF:in=/opt/observium/rrd/asr1-sv2/bgp-100.65.0.49.rrd:bgpPeerInUpdates:AVERAGE DEF:out_max=/opt/observium/rrd/asr1-sv2/bgp-100.65.0.49.rrd:bgpPeerOutUpdates:MAX DEF:in_max=/opt/observium/rrd/asr1-sv2/bgp-100.65.0.49.rrd:bgpPeerInUpdates:MAX CDEF:dout_max=out_max,-1,* CDEF:dout=out,-1,* CDEF:both=in,out,+ CDEF:alloctets=out,in,+ CDEF:wrongin=alloctets,UN,INF,UNKN,IF CDEF:wrongout=wrongin,-1,* AREA:in#AA66AA90 LINE1.25:in#AA66AA:'In ' GPRINT:in:LAST:.2lf%s GPRINT:in:AVERAGE:.2lf%s GPRINT:in_max:MAX:.2lf%s COMMENT:'\n' AREA:dout#FF660090: LINE1.25:dout#FF6600:'Out ' GPRINT:out:LAST:.2lf%s GPRINT:out:AVERAGE:.2lf%s GPRINT:out_max:MAX:.2lf%s COMMENT:\n AREA:wrongin#FFF2F2 AREA:wrongout#FFF2F2 HRULE:0#999999] RRD RUNTIME[0.0418s] RRD STDOUT[481x189] RRD_STATUS[TRUE] SQL[SELECT `attrib_value` FROM `entity_attribs` WHERE `entity_type` = 'device' AND `entity_id` = '77' AND `attrib_type` = 'disable_notify'] ROWS[1] SQL RUNTIME[0.00042892s] *(one that works from the same check)* ./test_alert.php -a 128255 -dd DEBUG! Load class 'Console_Color2' from '/opt/observium/libs/pear/Console/Color2.php': OK SQL[SELECT `attrib_value` FROM `observium_attribs` WHERE `attrib_type` = 'dbSchema';] ROWS[1] SQL RUNTIME[0.00032401s] SQL[SELECT @@SESSION.sql_mode;] ROWS[1] SQL RUNTIME[0.00017214s] SQL[SELECT `attrib_value` FROM `observium_attribs` WHERE `attrib_type` = 'current_rev';] ROWS[1] SQL RUNTIME[0.00025201s] SQL[SELECT * FROM `config`] ROWS[0] SQL RUNTIME[0.00023389s] Load class 'Net_IPv6' from '/opt/observium/libs/pear/Net/IPv6.php': OK Observium 0.16.10.8161 Test Alert Notification CMD[/opt/observium/scripts/distro] CMD EXITCODE[0] CMD RUNTIME[0.0164s] STDOUT[ Linux|3.10.0-327.36.1.el7.x86_64|amd64|CentOS|7.2.1511 ] CMD[/usr/bin/env python --version 2>&1] CMD EXITCODE[0] CMD RUNTIME[0.0051s] STDOUT[ Python 2.7.5 ] SQL[SELECT version();] ROWS[1] SQL RUNTIME[0.00030708s] CMD[/usr/bin/snmpget --version 2>&1] CMD EXITCODE[0] CMD RUNTIME[0.0081s] STDOUT[ NET-SNMP version: 5.7.2 ] CMD[/usr/bin/rrdtool --version | head -n1] CMD EXITCODE[0] CMD RUNTIME[0.0077s] STDOUT[ RRDtool 1.4.8 Copyright 1997-2013 by Tobias Oetiker <tobi(a)oetiker.ch> ] CMD[/usr/bin/rrdcached -h | head -n1] CMD EXITCODE[0] CMD RUNTIME[0.0074s] STDOUT[ RRDCacheD 1.4.8 ] CMD[/usr/bin/env apache2 -v | awk '/Server version:/ {print $3}'] CMD EXITCODE[0] CMD RUNTIME[0.0042s] STDOUT[ ] CMD[/usr/bin/env httpd -v | awk '/Server version:/ {print $3}'] CMD EXITCODE[0] CMD RUNTIME[0.0364s] STDOUT[ Apache/2.4.6 ] CMD[date "+%:z"] Wrong process status! Issue in proc_get_status(), see: https://bugs.php.net/bug.php?id=69014 CMD EXITCODE[0] CMD RUNTIME[0.003s] STDOUT[ -07:00 ] SQL[SELECT TIMEDIFF(NOW(), UTC_TIMESTAMP);] ROWS[1] SQL RUNTIME[0.00025392s] SQL[SELECT @@SESSION.sql_mode;] ROWS[1] SQL RUNTIME[0.00019908s] SQL[SHOW VARIABLES LIKE 'character_set_connection'] ROWS[1] SQL RUNTIME[0.00074387s] ##### Software versions ##### o OS Linux 3.10.0-327.36.1.el7.x86_64 [amd64] (CentOS 7.2.1511) o Apache 2.4.6 o PHP 5.4.16 o Python 2.7.5 o MySQL 5.5.50-MariaDB (extension: mysqli 5.5.50-MariaDB) o SNMP NET-SNMP 5.7.2 o RRDtool 1.4.8 (rrdcached 1.4.8: unix:/var/run/rrdcached/rrdcached.sock) ##### MySQL mode ##### o MySQL ##### Charset info ##### o PHP UTF-8 o MySQL utf8 ##### Timezones info ##### o Date Thursday, 20-Oct-16 21:46:44 PDT o PHP -07:00 o MySQL -07:00 SQL[SELECT * FROM `alert_tests` WHERE 1] ROWS[32] SQL RUNTIME[0.00056601s] Cached 32 alert rules. SQL[SELECT * FROM `alert_assoc`] ROWS[32] SQL RUNTIME[0.00039506s] SQL[SELECT * FROM `alert_table` WHERE `alert_table_id` = '128255'] ROWS[1] SQL RUNTIME[0.00037503s] SQL[SELECT * FROM `devices` WHERE `device_id` = '104'] ROWS[1] SQL RUNTIME[0.00044703s] SQL[SELECT * FROM `device_graphs` WHERE `device_id` = '104'] ROWS[28] SQL RUNTIME[0.00048900s] SQL[SELECT * FROM `bgpPeers` LEFT JOIN `bgpPeers-state` USING (`bgpPeer_id`) WHERE `bgpPeers`.`bgpPeer_id` = '509'] ROWS[1] SQL RUNTIME[0.00043297s] > $graphtype - /opt/observium/includes/alerts.inc.php:1170 /opt/observium/html/includes/graphs/graph.inc.php:33 ======================================================== array( [0] => string(11) "bgp_updates" [type] => string(3) "bgp" [1] => string(3) "bgp" [subtype] => string(7) "updates" [2] => string(7) "updates" ) SQL[SELECT * FROM `bgpPeers` WHERE `bgpPeer_id` = '509'] ROWS[1] SQL RUNTIME[0.00029802s] RRD PIPE OPEN[TRUE] RRD PIPE CLOSE[TRUE] RRD PIPE STDOUT[ OK u:0.03 s:0.01 r:0.03 ] RRD CMD[graph --daemon unix:/var/run/rrdcached/rrdcached.sock /tmp/5S0b4geqsVsq08iN.png -g -Y --lower-limit 0 --alt-autoscale-max --start 1476852404 --end 1477025204 --width 400 --height 150 -c BACK#EEEEEE00 -c SHADEA#EEEEEE00 -c SHADEB#EEEEEE00 -c FONT#000000 -c CANVAS#FFFFFF00 -c GRID#a5a5a5 -c MGRID#FF9999 -c FRAME#5e5e5e -c ARROW#5e5e5e -R normal --font LEGEND:8:'DroidSansMono,DejaVuSansMono' --font AXIS:7:'DroidSansMono,DejaVuSansMono' --font-render-mode normal -E COMMENT:'Updates Last Avg Max \n' DEF:out=/opt/observium/rrd/us1inet2/bgp-x.x.x.x.rrd:bgpPeerOutUpdates:AVERAGE DEF:in=/opt/observium/rrd/us1inet2/bgp-x.x.x.x.rrd:bgpPeerInUpdates:AVERAGE DEF:out_max=/opt/observium/rrd/us1inet2/bgp-x.x.x.x.rrd:bgpPeerOutUpdates:MAX DEF:in_max=/opt/observium/rrd/us1inet2/bgp-x.x.x.x.rrd:bgpPeerInUpdates:MAX CDEF:dout_max=out_max,-1,* CDEF:dout=out,-1,* CDEF:both=in,out,+ CDEF:alloctets=out,in,+ CDEF:wrongin=alloctets,UN,INF,UNKN,IF CDEF:wrongout=wrongin,-1,* AREA:in#AA66AA90 LINE1.25:in#AA66AA:'In ' GPRINT:in:LAST:.2lf%s GPRINT:in:AVERAGE:.2lf%s GPRINT:in_max:MAX:.2lf%s COMMENT:'\n' AREA:dout#FF660090: LINE1.25:dout#FF6600:'Out ' GPRINT:out:LAST:.2lf%s GPRINT:out:AVERAGE:.2lf%s GPRINT:out_max:MAX:.2lf%s COMMENT:\n AREA:wrongin#FFF2F2 AREA:wrongout#FFF2F2 HRULE:0#999999] RRD RUNTIME[0.0418s] RRD STDOUT[481x189] RRD_STATUS[TRUE] SQL[SELECT `attrib_value` FROM `entity_attribs` WHERE `entity_type` = 'device' AND `entity_id` = '104' AND `attrib_type` = 'disable_notify'] ROWS[0] SQL RUNTIME[0.00042915s] SQL[SELECT * FROM `alert_contacts` WHERE `contact_disabled` = 0 AND `contact_id` IN (SELECT `contact_id` FROM `alert_contacts_assoc` WHERE `aca_type` = 'alert' AND `alert_checker_id` = '39');] ROWS[2] SQL RUNTIME[0.00054097s] o Notifying [hipchat] Networking Alert: {"room_id":"","from":"Observium","token":""} REQUEST[https://api.hipchat.com/v2/room/xxxxxx/notification] REQUEST STATUS[204 No Content] REQUEST RUNTIME[0.5128s] RESPONSE[ ] > $http_response_header - /opt/observium/includes/alerts.inc.php:1271 /opt/observium/includes/common.inc.php:3213 ========================================================= array( [0] => string(23) "HTTP/1.1 204 No Content" [1] => string(30) "Access-Control-Allow-Origin: *" [2] => string(119) "Access-Control-Expose-Headers: Date, ETag, Link, X-RateLimit-Limit, X-RateLimit-Remaining, X-RateLimit-Reset, X-Backoff" [3] => string(23) "Content-Type: text/html" [4] => string(35) "Date: Fri, 21 Oct 2016 04:46:44 GMT" [5] => string(94) "Location: https://api.hipchat.com/v2/room/xxxxx/history/xxxxx-7c71-xxxx-xxxx-xxxxxxxx… " [6] => string(13) "Server: nginx" [7] => string(43) "Strict-Transport-Security: max-age=31536000" [8] => string(31) "X-Content-Type-Options: nosniff" [9] => string(22) "X-Ratelimit-Limit: 100" [10] => string(26) "X-Ratelimit-Remaining: 100" [11] => string(29) "X-Ratelimit-Reset: 1477025505" [12] => string(31) "X-XSS-Protection: 1; mode=block" [13] => string(17) "Connection: Close" ) > $opts - /opt/observium/includes/alerts.inc.php:1271 /opt/observium/includes/common.inc.php:3214 ================================================= array( [http] => array( [method] => string(4) "POST" [header] => string(174) "Connection: close Content-Type: application/json Content-Length: 275 Authorization: Bearer zomgWApDk5Wz9eK4kCReKjUDQxW1h9kMrRqDJnqy User-Agent: Observium/0.16.10.8161\r\n" [content] => string(275) "{"from":"Observium","color":"red","message_format":"html","message":"<a href=\"http:\/\/kansatsu.lol.com\/device\/device=104\/tab=alert\/alert_entry=128255\/\">ALERT: [us1inet2] [bgp_peer] [AS65028 x.x.x.x] <\/a><br \/>bgpPeerAdminStatus = start bgpPeerState = active"}" [timeout] => string(2) "15" ) ) o Notifying [email] Netops: {"email":"netops(a)lol.com"} Load class 'Mail_mime' from '/opt/observium/libs/pear/Mail/mime.php': OK Load class 'Mail' from '/opt/observium/libs/pear/Mail/Mail.php': OK PHP Strict Standards: Non-static method Mail::factory() should not be called statically in /opt/observium/includes/alerting/email.inc.php on line 176 Strict Standards: Non-static method Mail::factory() should not be called statically in /opt/observium/includes/alerting/email.inc.php on line 176 PHP Strict Standards: Non-static method PEAR::isError() should not be called statically in /opt/observium/includes/alerting/email.inc.php on line 180 Strict Standards: Non-static method PEAR::isError() should not be called statically in /opt/observium/includes/alerting/email.inc.php on line 180

2 5

Aggregating / stacking graphs capability
by Youssef BENGELLOUN - ZAHR 21 Oct '16

21 Oct '16

2 8

Check IPsec tunnel status on Juniper SRX firewalls
by Youssef BENGELLOUN - ZAHR 21 Oct '16

21 Oct '16

2 1

Context switches since upgrade
by William Bauer 21 Oct '16

21 Oct '16

I upgraded our community edition on Monday from the previous release dated 5/4/2016 to the latest release. I'm using observium to monitor the VM on which it is running, which is CentOS 6. The context switches graph has gone from hovering around 3500 to about 4200 immediately after the upgrade. System interrupts have increased by about the same percentage, and System I/O and Load Average have bumped up slightly. Are all of these typical of this upgrade? Nothing else was done to the system or to the devices being monitored. The increase in all these graphs (and a corresponding significant decrease in Observium performance) all correspond exactly in time to the upgrade. I've been wondering why it's performing worse, and then I noticed these items. Just looking for ideas or any helpful suggestions, and if this is to be expected. Thanks. Bill

2 1

Carel / pCo Discovery
by Robert Williams 21 Oct '16

21 Oct '16

Hi all, I see that there has just been an update to the detection of the Carel pCo controllers, which has added a lot of new sensor definitions for many people I expect (a good thing would have been an awful lot of work for someone which is appreciated of course!). Unfortunately, as the pCo is a programmable unit (and we are an OEM/unit programmer for Carel) we use the units for a large number of custom applications across a number of our facilities and customers. Previously we weren't getting any sensor-specific information via Observium for these units (just network, CPU, ram etc.) which is OK as we use other BMS systems to get the environmental data. Since the last update, we are getting a load of sensors but unfortunately (since our units are programmed by us) they are now showing alarms across most of the output, for example: The values being polled are also non-sensical because whatever the OIDs which are being used are either not aligned to anything we use or just totally irrelevant values. Humidity example below (obviously it's not 3,4 and 16 %): Interestingly, we do also have some 'official' Carel chiller controllers (running genuine Airedale control pCO units, not our own) - and these are also showing crazy values as chillers (no matter where you get them from) do not have 'Delivery Air Temperature' or 'Humidification Proportional Bands' as they don't' deal with air directly - for example: So it appears the detection logic is not just limited to incorrectly identifying our own custom controllers but also those of other manufacturers like Airedale, who also use Carel OEM pCO hardware like us. With all this in mind, can I ask what is the best way to prevent these devices from being detected as " Carel pCOWeb (Chiller Unit) ". So that they go back to being simple pCOWeb units with basic stats like Ethernet and CPU? Example device data is: So like I said at the start, I fully appreciate there was a lot of effort by someone to get all these sensors setup and that's great for people using the software they were configured to detect. I just need to 'not' detect our units as being the same really. Input welcome :) Cheers! Robert Williams Custodian Data Centre Email: Robert(a)CustodianDC.com http://www.CustodianDC.com

3 4

Can an alert checker match on mplsVpnVrfRouteDistinguisher?
by Pico Leto 20 Oct '16

20 Oct '16

Hi, I'm trying to build out an BGP peer alert for a specific vrf/mpls customer. My current Entity match is mplsVpnVrfRouteDistinguisher matches 707* I can see the route distinguisher via the debug of my ASR SQL[UPDATE `vrfs` set `mplsVpnVrfDescription` ='',`mplsVpnVrfRouteDistinguisher` ='707:707' WHERE `device_id` = '77' AND `vrf_oid` = '11.71.67.58.84.69.83.84.58.55.48.55'] SQL RUNTIME[0.00048089s] SQL[SELECT vrf_id FROM `vrfs` WHERE `device_id` = '77' AND `vrf_oid` = '11.71.67.58.84.69.83.84.58.55.48.55'] SQL RUNTIME[0.00037813s] When I rebuild my checker I dont get a match

1 0

RRD Graphs Not Generated.
by Laurence Mayer 20 Oct '16

20 Oct '16

Hi, I upgraded this morning to the latest version and for some reason the graphs are now not being generated (rrd). I do see the files being updated (date and time looks as of now). You can see here for example the CPUs are 100% (should be) however the graph shows nothing. [image: Inline image 1] Any ideas? Thanks Laurence

6 23

Custom reports capability
by Youssef BENGELLOUN - ZAHR 20 Oct '16

20 Oct '16

3 5

SNMP Location missing from Device attributes
by Youssef BENGELLOUN - ZAHR 19 Oct '16

19 Oct '16

3 4

Port FDB table
by Serghei Golipad 19 Oct '16

19 Oct '16

Guys, There used to be a tab under port properties with FDB info i.e vlan’s on a port if it’s a trunk. This has now gone. Any way to get it back? Cheers PLEASE CONSIDER THE ENVIRONMENT BEFORE PRINTING THIS EMAIL. CDW Limited is a Company registered in England and Wales. This email is sent for and on behalf of CDW Finance Holdings Limited. CDW Finance Holdings Limited is the UK holding company for CDW Limited trading as CDW. The registered office for CDW Finance Holdings Limited (Company Number 05872067) and its UK group undertakings is 10 Fleet Place, London, EC4M 7RB. VAT Registration 902 1949 39. Confidentiality: This e-mail contains proprietary information, some or all of which may be confidential and/or legally privileged. It is for the intended recipient only. If an addressing or transmission error has misdirected this e-mail, please notify the author by replying to this e-mail and then delete the original. If you are not the intended recipient you may not use, disclose, distribute, copy, print or rely on any information contained in this e-mail. You must not inform any other person other than CDW or the sender of its existence. For more information about CDW please visit www.uk.cdw.com

1 0

Entrepreneur de l’année : Votre vote peut faire la différence !
by Falco Schmutz 18 Oct '16

18 Oct '16

Bonjour à tous, Après avoir remporté le prix du public par EY (Ernst & Young), j’ai la chance d’être en finale pour le Prix de l’Entrepreneur de l’Année, en tant que CEO de Fitizzy. Vous me connaissez, je suis un homme de challenge ! Mais étant aussi un homme de conviction, je me permets de vous solliciter pour m’aider. Pour voter (en moins d’une minute, promis) : - Cliquez ici (http://nat.votes-eoy.fr/) - Renseignez votre / vos adresses mails. Vous recevrez ensuite un code - Copiez/collez ce code dans le lien de redirection - Et enfin, cliquez sur Fitizzy (pas les autres, hein). Merci d’avance pour votre aide & rendez vous ce soir pour les résultats ! Falco PS : Plein de nouveautés arrivent sur Premaccess, je vous tiendrai très bientôt informé ! ============================================================ This email was sent to observium(a)observium.org (mailto:observium@observium.org) why did I get this? (http://premaccess.us12.list-manage1.com/about?u=d01b1709a6276435a20292d6b&i…) unsubscribe from this list (http://premaccess.us12.list-manage.com/unsubscribe?u=d01b1709a6276435a20292…) update subscription preferences (http://premaccess.us12.list-manage.com/profile?u=d01b1709a6276435a20292d6b&…) PREMACCESS . 66 Av de Villiers . Paris 75017 . France

1 0

down icon wrong
by Simon Smith 18 Oct '16

18 Oct '16

Hi All is it just me or is the down icon on ports wrong? I’m getting what looks like a quarter of a circle? regards Simon

2 1

Re: [Observium] Include interface description/alias in Alerts
by Gumilar Siegfried 18 Oct '16

18 Oct '16

Sorry, I forgot to mention that I am using Telegram for notification transport. Von: observium [mailto:observium-bounces@observium.org] Im Auftrag von Moerman, Maarten Gesendet: Montag, 17. Oktober 2016 15:31 An: Observium Network Observation System Betreff: Re: [Observium] Include interface description/alias in Alerts It should be in the email that you get. You must be running a really old version then? Maarten From: observium <observium-bounces(a)observium.org<mailto:observium-bounces@observium.org>> on behalf of Gumilar Siegfried <siegfried.gumilar(a)stadtwerke-feldkirch.at<mailto:siegfried.gumilar@stadtwerke-feldkirch.at>> Reply-To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Date: Monday, October 17, 2016 at 3:07 PM To: "Observium Network Observation System (observium(a)observium.org<mailto:observium@observium.org>)" <observium(a)observium.org<mailto:observium@observium.org>> Subject: [Observium] Include interface description/alias in Alerts Hello! I have configured an alert checker for our Ports according to the documentation: Port is enabled, but operationally down Port ifAdminStatus equals up ifOperStatus notequals up ALL * ifType equals ethernetCsmacd Everything works fine, except the alerts only include the port number (e.g. Entity: Port13). I would like to include the interface description/alias too (e.g. Customer_xyz). Is there a way I can achieve this? Regards Siegfried

2 2

problem with snmp and brocade icx 6450
by Farshid Abediny 18 Oct '16

18 Oct '16

Hello, we have a brocade icx 6450 we enable snmp v2c on it and all of our other network monitoring can connect it (solarwinds and manageengine) but in observium can not connect, we check it with snmpwalk it seems snmpwalk can not connect to it , also we verify all things from our siwtch and it is ok, any idea how can we solve it? thanks

2 2

scaling graphs through variable
by Martijn Fennis 18 Oct '16

18 Oct '16

Hi, in our WAN we have multiple 100's ALIX boards connected through VPN. On eth1 we can scan all the info on the sublocations. On eth0 & eth2 we have various internet (local breakouts) connections with sometimes async ADSL modems. Is it somehow possible to retrieve a variable (that i have to insert manually / firewall) like ifAlias? It would be ideal to have up & download links per eth0 / eth2 parsed into scaling graphs on the ports tab. This way i can make alerts as we have no bandwidth throttling Regards, Martijn

1 0

Location menu gone after update
by William Bauer 18 Oct '16

18 Oct '16

I just updated our community edition to the latest, and the location dropdown in the devices menu is gone. We use that a ton--is there a way to get it back, perhaps in the config.php file? Thanks! Bill

3 4

Modify Dashboard - Switch "Status Warnings and Notifications"
by Richard Kucera 17 Oct '16

17 Oct '16

Dear Adam, Hello Community, my question is, if it's possible to move the "Status Warnings and Notifications" on XL screen to panel side. I modified already the dashboard for our need, the last thing is the "Status Warnings and Notifications" block. [cid:image001.png@01D228C4.17305430] Thank you in advance. Used Version: Observium 0.16.9.8118 (stable) Best regards from Switzerland Richard

2 2

NOC view
by MKS 17 Oct '16

17 Oct '16

Hello list I'm wondering if some of you are using observium as an alert system in a 24/7 NOC? I would like to have one window with open alerts, both from the alert checks and syslog alerts. Is it possible to copy the "syslog alerts" into the Alerts window (perhaps using some external program?) Regards MKS

1 0

syslog regex
by MKS 17 Oct '16

17 Oct '16

Hello list I'm having some problems with syslog alerts. RP/0/RSP0/CPU0:Oct 17 11:44:17.872 : isis[1010]: %ROUTING-ISIS-5-ADJCHANGE : Adjacency to ****** (Bundle-Ether1.7) (L2) Down, Holdtime expired RP/0/RSP0/CPU0:Oct 17 11:46:05.893 : isis[1010]: %ROUTING-ISIS-5-ADJCHANGE : Adjacency to ******* (Bundle-Ether1.7) (L2) Up, New adjacency I'm using the regex "/Adjacency.*Up/" and "/Adjacency.*Down/" The "/Adjacency.*Up/" alert is working fine, but the combo Adjacency and Down doesn't alert. If I match only on Adjacency or only on Down I do get an alert, both these two together don't work as expected. Any workarounds or a different regex I should use? Regards MKS

2 2

Re: [Observium] Include interface description/alias in Alerts
by Moerman, Maarten 17 Oct '16

17 Oct '16

It should be in the email that you get. You must be running a really old version then? Maarten From: observium <observium-bounces(a)observium.org<mailto:observium-bounces@observium.org>> on behalf of Gumilar Siegfried <siegfried.gumilar(a)stadtwerke-feldkirch.at<mailto:siegfried.gumilar@stadtwerke-feldkirch.at>> Reply-To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Date: Monday, October 17, 2016 at 3:07 PM To: "Observium Network Observation System (observium(a)observium.org<mailto:observium@observium.org>)" <observium(a)observium.org<mailto:observium@observium.org>> Subject: [Observium] Include interface description/alias in Alerts Hello! I have configured an alert checker for our Ports according to the documentation: Port is enabled, but operationally down Port ifAdminStatus equals up ifOperStatus notequals up ALL * ifType equals ethernetCsmacd Everything works fine, except the alerts only include the port number (e.g. Entity: Port13). I would like to include the interface description/alias too (e.g. Customer_xyz). Is there a way I can achieve this? Regards Siegfried

1 0

Include interface description/alias in Alerts
by Gumilar Siegfried 17 Oct '16

17 Oct '16

Hello! I have configured an alert checker for our Ports according to the documentation: Port is enabled, but operationally down Port ifAdminStatus equals up ifOperStatus notequals up ALL * ifType equals ethernetCsmacd Everything works fine, except the alerts only include the port number (e.g. Entity: Port13). I would like to include the interface description/alias too (e.g. Customer_xyz). Is there a way I can achieve this? Regards Siegfried

1 0

Observium Port Group alerts?
by Tomas 17 Oct '16

17 Oct '16

Hello, Simple question: Does Observium can add alert checker on group? For example, we have port group for x devices, so if we adding port alert we have to fill up Device Assocation and entity Association again. Thanks, Thom

4 6

Frontpage Map
by Zoellers, Billy 17 Oct '16

17 Oct '16

Looks like it's now defaulting to OpenStreetMap. I think it looks better, but it looks like none of my map config settings are working now. Are there new settings to use? For example: $config['frontpage']['map']['region'] = "US-KY"; $config['frontpage']['map']['resolution'] = "provinces"; $config['frontpage']['map']['zoom'] = "9"; $config['frontpage']['map']['center']['lat'] = "38.029"; $config['frontpage']['map']['center']['lng'] = "-84.496"; $config['frontpage']['map']['realworld'] = true; $config['frontpage']['map']['dotsize'] = 1; $config['frontpage']['map']['height'] = 450; [cid:DeanDortonbox.png] Billy Zoellers Infrastructure Engineer 106 W. Vine St., Ste 600 Lexington, KY 40507 ph (859) 425-7640 fax (859) 425-3640 CONFIDENTIALITY NOTICE: The preceding email message, and any files or attachments transmitted with it, may contain confidential and privileged information, and may constitute protected work product, confidential client information, trade secrets, and/or other non-public information. Furthermore, this message and any attachments may be protected by accountant/client privilege, attorney/client privilege, and/or other applicable privileges. Any unauthorized review, use, dissemination, distribution, disclosure, or reproduction of this message is strictly prohibited and may be unlawful. This message is intended to be conveyed and transmitted only to the designated recipient(s). If you are not an intended recipient of this message, please notify the sender immediately by email or by telephone at 859-255-2341. Also, please delete this email message including all attachments and destroy all copies. -- This mail was scanned by BitDefender For more information please visit http://www.bitdefender.com/frams/

3 3

syslog integration issue
by Grégory Lemblé 15 Oct '16

15 Oct '16

Morning, I try to implement the syslog.php features inside our Observium instance. on debug mode, we got syslog info inside the logs/debug.log file. But on the web side, impossible to get any message from the syslog. I'm not sure which area i need to investigate to get it done. Some help will be appreciate. Many Thanks ----------- Observium Version Pro 0.16.10.8118 (Stable) ----------- rsyslogd 7.4.4, compiled with: FEATURE_REGEXP: Yes FEATURE_LARGEFILE: No GSSAPI Kerberos 5 support: Yes FEATURE_DEBUG (debug build, slow code): No 32bit Atomic operations supported: Yes 64bit Atomic operations supported: Yes Runtime Instrumentation (slow code): No uuid support: Yes ----------- /etc/rsyslog.d/60-observium.conf: #--------------------------------------------------------- #send remote logs to observium $template observium,"%fromhost%||%syslogfacility%||%syslogpriority%||%syslogseverity%||%syslogtag%||%$year%-%$month%-%$day% %timereported:8:25%||%msg%||%programname%\n" $ModLoad omprog $ActionOMProgBinary /var/www/observium/syslog.php :inputname, isequal, "imudp" :omprog:;observium #& ~ & stop #--------------------------------------------------------- ----------- debug.log file: [2016/10/10 08:00:15 +0800] syslog.php(19124): hostname||1||4||4||auth:||2016-10-10 08:00:14|| User XXXXXXXXXXXX logout||auth [2016/10/10 08:00:15 +0800] syslog.php(19124): hostname||1||6||6||Security:||2016-10-10 08:00:15|| SSH login by public key from src IP XXXXXXX from src MAC XXXXX to USER EXEC mode using DSA as Server Host Key. ||Security ----------- config.php: $config['syslog']['debug'] = True; $config['enable_syslog'] = 1; // Enable Syslog $config['syslog']['fifo'] = FALSE; Front Web: No syslog entries found!Check that the syslog daemon and Observium configuration options are set correctly, that your devices are configured to send syslog to Observium and that there are no firewalls blocking the messages. See documentation <http://www.observium.org/wiki/Category:Documentation> and configuration options <http://www.observium.org/wiki/Configuration_Options#Syslog_Settings> for more information

2 2

Maintenance and down devices
by Jesse Defer 14 Oct '16

14 Oct '16

I've made a small change to change how down devices are displayed when in maintenance mode that seems generally useful enough to include in the distro. It scratches my itch of being able to quickly see what downed devices have scheduled maintenace. It would probably be useful to extend to more areas like the color of device links and other entities. In html/includes/print/status.inc.php (about line 66): if (isset($GLOBALS['cache']['maint']['device'][$device['device_id']])) $string .= ' <td><span class="label label-info">Device Down (Maintenance)</span></td>' . PHP_EOL; else $string .= ' <td><span class="label label-important">Device Down</span></td>' . PHP_EOL; Jesse

2 1

Unable to add Host
by Matt Vinson 13 Oct '16

13 Oct '16

I noticed the Wowza MIB was in a recent update from SVN so I tried adding one of my hosts to our Observium server and it states: No reply on community t-public-ss using v2c. Could not reach 'HOSTNAME' with given SNMP parameters using v2c. I have done an snmpwalk from the Observium server to the host in question and it works properly. Anybody have any idea why I can't add this host? Thanks! -- Regards, Matt Vinson --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

4 12

Add Mib and counter
by Jean CARUSO 13 Oct '16

13 Oct '16

hello, I'm new to the list. What is the procedure to add the MIBs manufacturer Huawei but the storage part Observium? I have them if needed Another question: Can you add to the manufacturer NetApp counters the snapmirror functionality. thank you in advance Regards [Description : E:\ADMINISTRATIF\Exemple Formulaire\ADMENTIS\ADMENTIS LOGO (1)\LOGO DOCUMENTS INTERNE\LOGO RVB ADM V1.jpg] Jean CARUSO Consultant Tél. : +334 42 24 37 97 Fax : +334 42 90 58 40 Gsm : +336 71 38 17 50 @ : jcaruso(a)admentis.fr<mailto:jcaruso@admentis.fr> P Imprimez seulement si nécessaire - Print only if necessary Ce message peut contenir des informations confidentielles, couvertes par le secret professionnel ou réservées exclusivement à leur destinataire. Toute lecture, utilisation, diffusion ou divulgation sans autorisation expresse est rigoureusement interdite. Si vous n'en êtes pas le destinataire, merci de prendre contact avec l'expéditeur et de détruire ce message. This email may contain material that is confidential, privileged and/or attorney work product for the sole use of the intended recipient. Any review, reliance or distribution by others or forwarding without express permission is strictly prohibited. If you are not the intended recipient, please contact the sender and delete all copies.

1 0

GraphViz Maps
by Andy Lemin 11 Oct '16

11 Oct '16

Hi Observium users, Re; GraphViz.js based maps built using; https://github.com/kedare/observium_map_generator https://gist.github.com/kedare/9806171 Hi, Their are a couple of graphing tools out there that use the "links" table, which does not seem to exist. Is there a replacement table that details the connections between devices? For example this no longer works :( SELECT UPPER(d.hostname) AS local_hostname, p.port_id AS local_port_id, p.ifName AS local_port, p.ifSpeed/1000000 as local_port_speed, l.remote_port_id AS remote_port_id, rp.ifName AS remote_port, UPPER(l.remote_hostname) AS remote_hostname, d.hardware AS hardware, rd.hardware AS remote_hardware, s.ifInErrors_rate AS local_in_errors_rate, s.ifOutErrors_rate AS local_out_errors_rate, s.ifInOctets_rate*8 AS local_in_octets_rate, s.ifOutOctets_rate*8 AS local_out_octets_rate, s.ifInOctets_perc AS local_in_octets_perc, s.ifOutOctets_perc AS local_out_octets_perc FROM `devices` AS d, `devices` as rd, `ports` AS p, `ports` as rp, `links` AS l, `ports-state` AS s WHERE p.port_id = l.local_port_id AND p.device_id = d.device_id AND rp.port_id = l.remote_port_id AND rp.device_id = rd.device_id AND p.port_id = s.port_id AND UPPER(d.hostname) = UPPER(%s); Thanks, Andy.

2 1

Billing Module Problem
by Andy Lemin 11 Oct '16

11 Oct '16

Hi, We are running the latest paid version, and turned on Billing last week. The cronjob is running fine but nothing comes up in the web interface? We followed; http://www.observium.org/docs/billing/ conrtab -l shows; # Billing */5 * * * * root php /opt/observium/poll-billing.php >> /dev/null 2>&1 1 * * * * root php /opt/observium/billing-calculate.php >> /dev/null 2>&1 And we have this in our config.php; // Billing $config['enable_billing'] = 1; # Enable Billing $config['billing']['customer_autoadd'] = 1; # Enable Auto-add bill per customer $config['billing']['circuit_autoadd'] = 1; # Enable Auto-add bill per circuit_id $config['billing']['bill_autoadd'] = 1; # Enable Auto-add bill per bill_id However nothing is being auto added? So we added a bill manually, and when running the cronjob scripts manually all seems to work fine, but after leaving it for a week (so data could build up) we still see this JpGraph error; Thanks, Andy.

3 20

Billing Graphs 2 hours ahead
by Lyndon Labuschagne 11 Oct '16

11 Oct '16

HI All Can anyone point me in the right direction? The billing graphs are working well, but for some reason the graph is 2 hours ahead. I assumed it may be the date.timezone setting in php.ini but that wasn't it. Thought it may have been the router time zone or incorrect NTP info, but that is also correct. The Last Polled and Last Calculated times are correct. Im sure its something simple that I am missing, but I can't fine it.

2 3

Authentication via FreeIPA
by Zarko Dudic 10 Oct '16

10 Oct '16

Hi there I want to be good citizens and check first Archives but this link was not found. http://postman.memetic.org/pipermail/observium/ Anyway, I try configuring Observium (*Observium CE *0.16.1.7533) to authenticate via LDAP, it's FreeIPA server using 389 Directory Service for ldap service. Unfortunately I can't make it to login. 1) The config.php reads: $config['auth_ldap_version'] = 3; // v2 or v3 $config['auth_ldap_server'] = "ca-ldap01.x.com"; $config['auth_ldap_port'] = 389; $config['auth_ldap_starttls'] = OPTIONAL; $config['auth_ldap_prefix'] = "uid="; $config['auth_ldap_suffix'] = ",cn=users,cn=accounts,dc=us,dc=x,dc=com"; $config['auth_ldap_attr']['uid'] = "uid"; // LDAP attribute containing user login name $config['auth_ldap_attr']['uidNumber'] = "uidNumber"; // LDAP attribute containing numeric user ID $config['auth_ldap_attr']['dn'] = "dn"; // LDAP attribute containing user's DN $config['auth_ldap_attr']['gidNumber'] = "gidNumber"; // LDAP attribute containing group id number $config['auth_ldap_objectclass'] = "posixaccount"; // objectClass to filter out valid users, use * for all objects under ldap_suffix tree $config['auth_ldap_groupmemberattr'] = "memberUid"; 2) Wireshark on Observium system gives: 1 0.000000000 observium-ip -> ldap-ip TCP 74 42240 > ldap [SYN] Seq=0 Win=14600 Len=0 MSS=1460 SACK_PERM=1 TSval=2573095638 TSecr=0 WS=128 2 0.006589311 ldap-ip -> observium-ip TCP 74 ldap > 42240 [SYN, ACK] Seq=0 Ack=1 Win=14480 Len=0 MSS=1460 SACK_PERM=1 TSval=327213350 TSecr=2573095638 WS=128 3 0.006626711 observium-ip -> ldap-ip TCP 66 42240 > ldap [ACK] Seq=1 Ack=1 Win=14720 Len=0 TSval=2573095644 TSecr=327213350 4 0.006747394 observium-ip -> ldap-ip LDAP 144 bindRequest(1) "uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" simple 5 0.013069430 ldap-ip -> observium-ip TCP 66 ldap > 42240 [ACK] Seq=1 Ack=79 Win=14592 Len=0 TSval=327213357 TSecr=2573095644 6 0.603341264 ldap-ip -> observium-ip LDAP 80 bindResponse(1) success 7 0.603369077 observium-ip -> ldap-ip TCP 66 42240 > ldap [ACK] Seq=79 Ack=15 Win=14720 Len=0 TSval=2573096241 TSecr=327213947 8 0.603652020 observium-ip -> ldap-ip LDAP 149 searchRequest(2) "cn=users,cn=accounts,dc=us,dc=x,dc=com" wholeSubtree 9 0.610210283 ldap-ip -> observium-ip TCP 66 ldap > 42240 [ACK] Seq=15 Ack=162 Win=14592 Len=0 TSval=327213954 TSecr=2573096241 10 0.614501121 ldap-ip -> observium-ip LDAP 3377 searchResEntry(2) "uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" | searchResDone(2) success 11 0.614533639 observium-ip -> ldap-ip TCP 66 42240 > ldap [ACK] Seq=162 Ack=3326 Win=21248 Len=0 TSval=2573096252 TSecr=327213958 12 0.615170867 observium-ip -> ldap-ip LDAP 144 bindRequest(3) "uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" simple 13 0.628537773 ldap-ip -> observium-ip LDAP 80 bindResponse(3) success 14 0.635412239 observium-ip -> ldap-ip LDAP 73 unbindRequest(4) 15 0.635506320 observium-ip -> ldap-ip TCP 66 42240 > ldap [FIN, ACK] Seq=247 Ack=3340 Win=21248 Len=0 TSval=2573096273 TSecr=327213973 16 0.642012247 ldap-ip -> observium-ip TCP 66 ldap > 42240 [FIN, ACK] Seq=3340 Ack=248 Win=14592 Len=0 TSval=327213986 TSecr=2573096273 17 0.642029914 observium-ip -> ldap-ip TCP 66 42240 > ldap [ACK] Seq=248 Ack=3341 Win=21248 Len=0 TSval=2573096280 TSecr=327213986 3) Ldap logs read: conn=348 fd=83 slot=83 connection from observium-ip to ldap-ip conn=348 op=0 BIND dn="uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" method=128 version=3 conn=348 op=0 RESULT err=0 tag=97 nentries=0 etime=0 dn="uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" conn=348 op=1 SRCH base="cn=users,cn=accounts,dc=us,dc=x,dc=com" scope=2 filter="(uid=zarko)" attrs=ALL conn=348 op=1 RESULT err=0 tag=101 nentries=1 etime=0 conn=348 op=2 BIND dn="uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" method=128 version=3 conn=348 op=2 RESULT err=0 tag=97 nentries=0 etime=0 dn="uid=zarko,cn=users,cn=accounts,dc=us,dc=x,dc=com" conn=348 op=3 UNBIND conn=348 op=3 fd=83 closed - U1 conn=67 op=22 SRCH base="ou=sessions,ou=Security Domain,o=ipaca" scope=2 filter="(objectClass=securityDomainSessionEntry)" attrs="cn" conn=67 op=22 RESULT err=0 tag=101 nentries=0 etime=0 conn=15 op=1354 SRCH base="ou=group,dc=ignore,dc=me" scope=1 filter="(&(objectClass=posixGroup)(gidNumber=1001))" attrs="cn gidNumber userPassword memberUid" conn=15 op=1354 RESULT err=32 tag=101 nentries=0 etime=0 conn=15 op=1355 SRCH base="cn=users,cn=accounts,dc=us,dc=x,dc=com" scope=1 filter="(&(objectClass=posixAccount)(uidNumber=1001))" attrs="cn uid uidNumber gidNumber gecos description homeDirectory loginShell" conn=15 op=1355 RESULT err=0 tag=101 nentries=0 etime=0 4) Thanks in advance for any suggestion or troubleshooting tips. -- Thanks, Zarko

3 9

Question about PDF | CSV Reports
by Francisco José Sánchez Iruela 10 Oct '16

10 Oct '16

Hi All, Anyone know if Could I get a report billing (.pdf or .csv) at the end of each month for each customer (Bill) ?? Best regards, -- Francisco José Sánchez IruelaDepartamento de redes <http://www.cartagon.com/> *Tel.* 902 998 398 – (+34) 91 020 11 32 - *Extensión 2105* *Fax.* 902 998 374 – (+34) 91 362 46 46 *E-mail.* fjsanchez(a)cartagon.com Calle Urano 50, 28760, Tres Cantos. Madrid *Web.* www.cartagon.com <https://www.linkedin.com/company/cartagon> <https://twitter.com/cartagon>

1 0

Discover new devices problem
by zois roupas 10 Oct '16

10 Oct '16

Hello everyone, Great Documentation and so far it's a great tool. One question though because i can't find a way to get auto discover new devices to work. Everything works great when adding the device ./add_device.php <ip> public v2c but when running ./discovery.php -h new , 0 devices discovered. I guess it's not a problem with the SNMP cause it wouldn't work with the manual ip addition, right? So the next step was to check the hosts file from the observium server. so this is the config 192.168.1.2 test-01.home.com #(machine to discover) The sysName variable from the machine that i want to discover is Linux test-01 3.10.0-327.36.1.el7.x86_64 #1 SMP Sun Sep 18 13:04:29 UTC 2016 x86_64 x86_64 The firewall is disabled in both machines Sorry for the trouble but what am i missing here? Thanks for the time Zois

1 0

syslog integration issue
by Grégory Lemblé 10 Oct '16

10 Oct '16

Morning, I try to implement the syslog.php features inside our Observium instance. on debug mode, we got syslog info inside the logs/debug.log file. But on the web side, impossible to get any message from the syslog. I'm not sure which area i need to investigate to get it done. Some help will be appreciate. Many Thanks ----------- Observium Version Pro 0.16.10.8118 (Stable) ----------- rsyslogd 7.4.4, compiled with: FEATURE_REGEXP: Yes FEATURE_LARGEFILE: No GSSAPI Kerberos 5 support: Yes FEATURE_DEBUG (debug build, slow code): No 32bit Atomic operations supported: Yes 64bit Atomic operations supported: Yes Runtime Instrumentation (slow code): No uuid support: Yes ----------- /etc/rsyslog.d/60-observium.conf: #--------------------------------------------------------- #send remote logs to observium $template observium,"%fromhost%||%syslogfacility%||%syslogpriority%||% syslogseverity%||%syslogtag%||%$year%-%$month%-%$day% %timereported:8:25%||%msg%||%programname%\n" $ModLoad omprog $ActionOMProgBinary /var/www/observium/syslog.php :inputname, isequal, "imudp" :omprog:;observium #& ~ & stop #--------------------------------------------------------- ----------- debug.log file: [2016/10/10 08:00:15 +0800] syslog.php(19124): hostname||1||4||4||auth:||2016-10-10 08:00:14|| User XXXXXXXXXXXX logout||auth [2016/10/10 08:00:15 +0800] syslog.php(19124): hostname||1||6||6||Security:||2016-10-10 08:00:15|| SSH login by public key from src IP XXXXXXX from src MAC XXXXX to USER EXEC mode using DSA as Server Host Key. ||Security ----------- config.php: $config['syslog']['debug'] = True; $config['enable_syslog'] = 1; // Enable Syslog $config['syslog']['fifo'] = FALSE; ------------- Front Web: No syslog entries found!Check that the syslog daemon and Observium configuration options are set correctly, that your devices are configured to send syslog to Observium and that there are no firewalls blocking the messages. See documentation <http://www.observium.org/wiki/Category:Documentation> and configuration options <http://www.observium.org/wiki/Configuration_Options#Syslog_Settings> for more information

1 0

Re: [Observium] Auto discovery
by Mikey van der Worp 07 Oct '16

07 Oct '16

To whom it may concern, Currently we are having some issues with Observium's Auto Discovery. The problem is that it currently only discovers about 10% of the network. Does somebody have a clue on how to fix this issue? We already disabled the option "require valid hostnames" at the auto discovery settings. Unfortunately after changing this option, it only discovered about 10 more devices. Also we do not have any problems with the CDP neighbours on our switches. Best regards, Mikey van der Worp -- Mikey van der Worp System Engineer Utelisys Communications B.V. Trinity Buildings Tower A, 7th floor Pietersbergweg 15 1105BM Amsterdam M +31 (0) 62 942 2052 T +31 (0) 20 561 8010 F +31 (0) 20 561 8021 www.utelisys.com<http://www.utelisys.com> - https://www.utelisys.com/

3 2