- observium - lists.observium.org

Check IPsec tunnel status on Juniper SRX firewalls
by Youssef BENGELLOUN - ZAHR 21 Oct '16

21 Oct '16

2 1

Context switches since upgrade
by William Bauer 21 Oct '16

21 Oct '16

I upgraded our community edition on Monday from the previous release dated 5/4/2016 to the latest release. I'm using observium to monitor the VM on which it is running, which is CentOS 6. The context switches graph has gone from hovering around 3500 to about 4200 immediately after the upgrade. System interrupts have increased by about the same percentage, and System I/O and Load Average have bumped up slightly. Are all of these typical of this upgrade? Nothing else was done to the system or to the devices being monitored. The increase in all these graphs (and a corresponding significant decrease in Observium performance) all correspond exactly in time to the upgrade. I've been wondering why it's performing worse, and then I noticed these items. Just looking for ideas or any helpful suggestions, and if this is to be expected. Thanks. Bill

2 1

Carel / pCo Discovery
by Robert Williams 21 Oct '16

21 Oct '16

Hi all, I see that there has just been an update to the detection of the Carel pCo controllers, which has added a lot of new sensor definitions for many people I expect (a good thing would have been an awful lot of work for someone which is appreciated of course!). Unfortunately, as the pCo is a programmable unit (and we are an OEM/unit programmer for Carel) we use the units for a large number of custom applications across a number of our facilities and customers. Previously we weren't getting any sensor-specific information via Observium for these units (just network, CPU, ram etc.) which is OK as we use other BMS systems to get the environmental data. Since the last update, we are getting a load of sensors but unfortunately (since our units are programmed by us) they are now showing alarms across most of the output, for example: The values being polled are also non-sensical because whatever the OIDs which are being used are either not aligned to anything we use or just totally irrelevant values. Humidity example below (obviously it's not 3,4 and 16 %): Interestingly, we do also have some 'official' Carel chiller controllers (running genuine Airedale control pCO units, not our own) - and these are also showing crazy values as chillers (no matter where you get them from) do not have 'Delivery Air Temperature' or 'Humidification Proportional Bands' as they don't' deal with air directly - for example: So it appears the detection logic is not just limited to incorrectly identifying our own custom controllers but also those of other manufacturers like Airedale, who also use Carel OEM pCO hardware like us. With all this in mind, can I ask what is the best way to prevent these devices from being detected as " Carel pCOWeb (Chiller Unit) ". So that they go back to being simple pCOWeb units with basic stats like Ethernet and CPU? Example device data is: So like I said at the start, I fully appreciate there was a lot of effort by someone to get all these sensors setup and that's great for people using the software they were configured to detect. I just need to 'not' detect our units as being the same really. Input welcome :) Cheers! Robert Williams Custodian Data Centre Email: Robert(a)CustodianDC.com http://www.CustodianDC.com

3 4

Can an alert checker match on mplsVpnVrfRouteDistinguisher?
by Pico Leto 20 Oct '16

20 Oct '16

Hi, I'm trying to build out an BGP peer alert for a specific vrf/mpls customer. My current Entity match is mplsVpnVrfRouteDistinguisher matches 707* I can see the route distinguisher via the debug of my ASR SQL[UPDATE `vrfs` set `mplsVpnVrfDescription` ='',`mplsVpnVrfRouteDistinguisher` ='707:707' WHERE `device_id` = '77' AND `vrf_oid` = '11.71.67.58.84.69.83.84.58.55.48.55'] SQL RUNTIME[0.00048089s] SQL[SELECT vrf_id FROM `vrfs` WHERE `device_id` = '77' AND `vrf_oid` = '11.71.67.58.84.69.83.84.58.55.48.55'] SQL RUNTIME[0.00037813s] When I rebuild my checker I dont get a match

1 0

RRD Graphs Not Generated.
by Laurence Mayer 20 Oct '16

20 Oct '16

Hi, I upgraded this morning to the latest version and for some reason the graphs are now not being generated (rrd). I do see the files being updated (date and time looks as of now). You can see here for example the CPUs are 100% (should be) however the graph shows nothing. [image: Inline image 1] Any ideas? Thanks Laurence

6 23

Custom reports capability
by Youssef BENGELLOUN - ZAHR 20 Oct '16

20 Oct '16

3 5

SNMP Location missing from Device attributes
by Youssef BENGELLOUN - ZAHR 19 Oct '16

19 Oct '16

3 4

Port FDB table
by Serghei Golipad 19 Oct '16

19 Oct '16

Guys, There used to be a tab under port properties with FDB info i.e vlan’s on a port if it’s a trunk. This has now gone. Any way to get it back? Cheers PLEASE CONSIDER THE ENVIRONMENT BEFORE PRINTING THIS EMAIL. CDW Limited is a Company registered in England and Wales. This email is sent for and on behalf of CDW Finance Holdings Limited. CDW Finance Holdings Limited is the UK holding company for CDW Limited trading as CDW. The registered office for CDW Finance Holdings Limited (Company Number 05872067) and its UK group undertakings is 10 Fleet Place, London, EC4M 7RB. VAT Registration 902 1949 39. Confidentiality: This e-mail contains proprietary information, some or all of which may be confidential and/or legally privileged. It is for the intended recipient only. If an addressing or transmission error has misdirected this e-mail, please notify the author by replying to this e-mail and then delete the original. If you are not the intended recipient you may not use, disclose, distribute, copy, print or rely on any information contained in this e-mail. You must not inform any other person other than CDW or the sender of its existence. For more information about CDW please visit www.uk.cdw.com

1 0

Entrepreneur de l’année : Votre vote peut faire la différence !
by Falco Schmutz 18 Oct '16

18 Oct '16

Bonjour à tous, Après avoir remporté le prix du public par EY (Ernst & Young), j’ai la chance d’être en finale pour le Prix de l’Entrepreneur de l’Année, en tant que CEO de Fitizzy. Vous me connaissez, je suis un homme de challenge ! Mais étant aussi un homme de conviction, je me permets de vous solliciter pour m’aider. Pour voter (en moins d’une minute, promis) : - Cliquez ici (http://nat.votes-eoy.fr/) - Renseignez votre / vos adresses mails. Vous recevrez ensuite un code - Copiez/collez ce code dans le lien de redirection - Et enfin, cliquez sur Fitizzy (pas les autres, hein). Merci d’avance pour votre aide & rendez vous ce soir pour les résultats ! Falco PS : Plein de nouveautés arrivent sur Premaccess, je vous tiendrai très bientôt informé ! ============================================================ This email was sent to observium(a)observium.org (mailto:observium@observium.org) why did I get this? (http://premaccess.us12.list-manage1.com/about?u=d01b1709a6276435a20292d6b&i…) unsubscribe from this list (http://premaccess.us12.list-manage.com/unsubscribe?u=d01b1709a6276435a20292…) update subscription preferences (http://premaccess.us12.list-manage.com/profile?u=d01b1709a6276435a20292d6b&…) PREMACCESS . 66 Av de Villiers . Paris 75017 . France

1 0

down icon wrong
by Simon Smith 18 Oct '16

18 Oct '16

Hi All is it just me or is the down icon on ports wrong? I’m getting what looks like a quarter of a circle? regards Simon

2 1