- observium - lists.observium.org

Port Labeling
by Christian 05 Apr '18

05 Apr '18

Hello, I was introduced to Observium in early March, and coming from a Nagios / Cacti type of monitoring, I am completely impressed with the power of Observium. I have CE 17.9.0 and am in the process of deploying it at my location. I have a couple of smart switches that support SNMP, but are not capable of a Port label. Thus, Observium shows the switch as Port 1, Port 2, Port 3 instead of my desired “Port 1 - Bandwidth Control” “Port 2 - Linux Server” “Port 3 - Printer” … that sort of thing. I found that I could use NaviCat to edit the MySQL database to properly label the ports, but then the next polling cycle restores the generic port label 5 minutes later. Is there any way for me to modify the polling to leave the label alone? I don’t want to look into “locking” the [port_label] field of the database tables. If I may also ask, is there any way to tell Observium that a down port is the normal (green) condition? I have some switches with ports that are not active, and if something is plugged into them, an alert would be handy. Thank you again for this amazing software. Christian

1 0

Function gone missing
by Mike Hyslop 04 Apr '18

04 Apr '18

Hi guys. I have noticed that our weathermap has stopped updating, when I run it in debug mode it moans about function check_extension_exists() being missing. I have had a quick look through the source and can't see that function anywhere. Not sure if its been depreciated or renamed (or if it was surplus to requirements and simply removed) Cheers. [Accesspoint Logo] [Roundel Logo] Mike Hyslop Senior Infrastructure Engineer [email icon] mike.hyslop(a)theaccesspoint.co.uk [phone icon] DDI: 020 8102 1121 Office: 020 3189 2645 [website icon] www.theaccesspoint.co.uk<http://www.theaccesspoint.co.uk> [address icon] Accesspoint | Unit 7 | Ashton Gate | Ashton Road | Harold Hill | RM3 8UF [group logos] [website icon] Please think of the environment before you print this email This document should only be read by those persons to whom it is addressed. Accordingly, Accesspoint Group Holdings Ltd and its subsidiary companies disclaim all responsibility and accept no liability (including in negligence) for the consequences of any such persons other than the addressee acting, or refraining from acting, on such information prior to the receipt by those persons of subsequent written confirmation. If you have received this e-mail message in error, please notify us immediately by telephone (0203 189 2645). Please also destroy and delete the message from your computer. Any form of reproduction, dissemination, copying, disclosure, modification, distribution and/or publication of this e-mail message is strictly prohibited. Accesspoint Group Holdings Ltd, Accesspoint Technologies Ltd and Accesspoint Legal Services Ltd are companies registered in England and Wales. www.theaccesspoint.co.uk<http://www.theaccesspoint.co.uk/> The risk of fraud relating to emails and bank account details has increased. We will NOT email you to tell you that our bank account details have changed; any such email is a scam. Please check our bank account details with us in person if you are in any doubt. We will not accept responsibility if you transfer money into an incorrect account.

1 0

"External Web URL" not set or incorrect,
by Eric W. Bates 03 Apr '18

03 Apr '18

I'm getting the message: Setting 'web_url' for "External Web URL" not set or incorrect, please update on Global Settings Edit page. I'm currently connecting to the URL: https://observium.whoi.edu/ And the setting is: http://observium.whoi.edu/ However, the settings page will not accept the 's' character. Every time I add it, it simply disappears again. The defaults in includes/defaults.inc.php has: #$config['base_url'] = "http://localhost/"; // Not recomend change this, only if autodetect wrong. Used in WUI #$config['web_url'] = "http://localhost:80/"; // This same as base_url but used only in cli for example in alerts Should I change to: $config['web_url'] = "https://localhost:443/" -- Clark 159a, MS 46 508/289-3112

1 0

BitRRD: Blockchain-based data storage for Observium
by Adam Armstrong 02 Apr '18

02 Apr '18

Hi Guys, We're proud to announce that we're switching to BitRRD, the new blockchain-based metric storage format. http://www.observium.org/blockchain/ The migration should be seemless, provided your server has 6-8 GPUs installed when you perform the update. Thanks, adam.

6 9

taildrops counted as errors since junos 15.X on EX series
by Arne Van Theemsche 01 Apr '18

01 Apr '18

Hi, we started to upgrade our juniper EX switches to 15.X release and notice a change of behaviour in error reporting at interface level in observium the problem lays that taildrops (which are activated by default and cannot just be, and isn't even a good practice to disable them) are now reported as errors in observium Output errors: Carrier transitions: 29, Errors: 0, Drops: 177209, Collisions: 0, Aged packets: 0, FIFO errors: 0, HS link CRC errors: 0, MTU errors: 0, Resource errors: 0 show interfaces queue xe-0/0/4 .... Tail-dropped packets : 177209 ...... prior to 15.X we only received reports/mails if the Errors Value was > 0. Honestly, we only care about errors, because taildrops will always happen from time to time I don't know if this is a change in behaviour of juniper snmp counters or that this is a flag in observium we can toggle? thx Arne

2 1

Question on Traffic Comparison widget
by Aaron Mayfield 28 Mar '18

28 Mar '18

I’ve been messing around with the Default Dashboard since I noticed it recently. What should the Traffic Comparison widget show? For me, I’m getting the red Draw Error: [cid:image001.png@01D3BD1D.F03E1CA0] Is this something that should be working as of now? Thanks Aaron Mayfield

2 1

Create Load Averages Alert Checker
by H Box 28 Mar '18

28 Mar '18

Hi All, I create successfully a alert for device downtime and diskspace use, but cannot find the right info to create a alert for load averages into http://www.observium.org/docs/entities Can someone help me with this? Thanks allot for your feedback.

6 7

Re: [Observium] Can't write new info to Observium
by Karolis Birgėla 28 Mar '18

28 Mar '18

On 2017.02.22 14:00, observium-request(a)observium.org wrote: > Can't write new info to Observium I've attached a picture of how it looks like in the device search. You can see that some devices don't have their models written. It's actually important, as we have many devices in Observium.

2 1

Clearing Alerts
by mal＠platinumnetworks.com.au 28 Mar '18

28 Mar '18

Hi all - I have created my very first alert checker and can see that it creates and alert according to the checker criteria. My checker looks for speed on a port and alerts if ge 100M. >From what I can see, once that alert has been created I do not have the ability to 'clear' the alert so even if the port speed drops below 100M the alert remains in failed state and if the checker criteria are met again a new alert is not created. My use case is that I need to monitor the bandwidth utilisation on this specific port on an ongoing basis and be alerted each time the speed exceeds say 100M. Appreciate any pointers to show me where I am going wrong. Cheers Mal

2 1

Switch ignored ports
by Luca Sasdelli 26 Mar '18

26 Mar '18

Hi all, on a switch only I see all phy ports as ignored: +---------+-----------+----------+---------+-----------+-----------+---------+ | ifIndex | ifDescr | ifName | ifAlias | ifType | Oper St | Ignored | | | | | | | atus | | +---------+-----------+----------+---------+-----------+-----------+---------+ | 1 | Host Data | host.1.1 | ... | propVirtu | up | no | | | Port | | | al | | | | 2 | Enterpris | lo.1.1 | ... | softwareL | up | no | | | e Network | | | oopback | | | | | s, Inc. S | | | | | | | | ... | | | | | | | 12001 | Enterasys | ge.1.1 | ... | ethernetC | up | yes | | | Networks | | | smacd | | | | | , Inc. 10 | | | | | | | | ... | | | | | | | 12002 | Enterasys | ge.1.2 | ... | ethernetC | up | yes | | | Networks | | | smacd | | | | | , Inc. 10 | | | | | | On the same network there are other Enterasys/Extreme Networks switches and they're regularly discovered. I've deleted and re-created the switch entry, but it doesn't change. What checks should I do? Cheers Luca

3 3