- observium - lists.observium.org

Juniper port polling problems
by Andrey 03 Nov '17

03 Nov '17

Hi, I have observium 0.16.1.7533. It has problems with two machines: Juniper mx240 with JunOS 15.1R2 and Juniper EX4550-32F with JunOS 12.3R12.4. This devices very slow polling ports information. Here I found the same problem: http://jira.observium.org/browse/OBSERVIUM-1695 <http://jira.observium.org/browse/OBSERVIUM-1695> But there it is written that "junipers have functionally broken SNMP stacks". Is there any solution to this issue? Are there any special settings or modules for JunOS ? Thanks.

6 10

Optic dbm alert checker and interface status
by Milton Ngan 03 Nov '17

03 Nov '17

Hi, Is there a way to only trigger the dbm sensor alert if the corresponding interface is up? I thought I could get away with just testing if the sensor values fall outside the sensor limits. But when ports are down (even when unplugged) I get spiky readings which will trigger the alert. So it would be nice to check if the interface is up as part of the alert check. I suspect this isn't possible as things are right now. It seems sensors have no relationship to another entity (e.g a port on a router). Ideally, I would like to say something like this: Port Checker Condition ifOperStatus eq up sensors.dbm.juniper-dom-rx.sensor_value < @sensors.dbm.juniper-dom-rx.sensor_limit_low Port Checker Entity Match ifAdminStatus eq up dbm in sensor_classes juniper-dom-rx in sensor_types So only ports that are admin up and have an associated sensor type of the appropriate type would get added to the checker. This will ensure the condition will be able to refer to the appropriate sensor. This would imply there is some mapping/relationship between sensors and other entities. This is probably very MIB specific and very platform specific. But it would make for a very useful checker.

2 2

Syslog alerts empty email
by Philippe Hurtubise 03 Nov '17

03 Nov '17

Hi, I updated to latest SVN yesterday and still receiving empty email. See below. Thanks From: Observium.SNMP(a)autolog.int [mailto:Observium.SNMP@autolog.int] Sent: Friday, November 3, 2017 6:05 AM To: Philippe Hurtubise <philippe.hurtubise(a)autolog.com> Subject: Modify Alert Metrics Duration Device Device Hardware Operating System Location Uptime E-mail sent to: philippe.hurtubise(a)autolog.com<mailto:philippe.hurtubise@autolog.com> E-mail sent at: Fri, 03 Nov 2017 06:05:16 -0400 -- Observium Professional 17.10.8930<http://www.observium.org>

2 2

some devices takes very long to complete /opt/observium/poller.php process
by Edvinas K 03 Nov '17

03 Nov '17

Hello, Some devices takes very long to complete /opt/observium/poller.php process. For example i took one of them and run: /opt/observium/poller-wrapper.py --host hk2net01a -d /opt/observium/poller-wrapper.py:568: Warning: Data truncated for column 'process_name' at row 1 cursor.execute(p_query, (pid,ppid,processname,uid,command,s_time)) INFO: starting the poller at 2017/11/02 17:10:50 with 16 threads WARNING: DEBUG enabled, each device poller store output to /tmp/observium_poller_id.debug (where id is device_id) /usr/bin/env php /opt/observium/poller.php -d -h 320 >> /tmp/observium_poller_320.debug 2>&1 INFO: starting alerter.php for 320 INFO: finished alerter.php for 320 WARNING: worker Thread-1 finished device 320 in 405 seconds INFO: poller-wrapper.py poller --host hk2net01a processed 1 devices in 405.53 seconds with 16 threads, load average (5min) 1.67 WARNING: the process took more than 5 minutes to finish, you need faster hardware or more threads INFO: in sequential style processing the elapsed time would have been: 405 seconds WARNING: device 320 is taking too long: 405 seconds ERROR: Some devices are taking more than 300 seconds, the script cannot recommend you what to do. Number of rows updated: 1 DEBUG: /usr/bin/rrdtool update /opt/observium/rrd/poller-wrapper.rrd N:1:405.531:16 DEBUG: /usr/bin/rrdtool update /opt/observium/rrd/poller-wrapper_count.rrd N:1 The debug txt shows that it freezes for about 4mins on this line: "SQL RUNTIME[0.00020313s] o Caching Oids Used full table ifEntry/ifXEntry snmpwalk. ifEntry CMD[/usr/bin/snmpbulkwalk -v2c -c *** -Pu -OQUs -m IF-MIB -M /opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp 'udp':'hk2net01a':'161' ifEntry] ...................." and almost after 5mins it resumes. What could be the reason ? Thanks.

5 9

Empty email
by Philippe Hurtubise 02 Nov '17

02 Nov '17

Hi, Since I enabled syslog alerting, I receive empty email like this. Thanks From: Observium.SNMP(a)autolog.int [mailto:Observium.SNMP@autolog.int] Sent: Thursday, November 2, 2017 6:15 AM To: Philippe Hurtubise <philippe.hurtubise(a)autolog.com> Subject: Modify Alert Metrics Duration Device Device Hardware Operating System Location Uptime E-mail sent to: philippe.hurtubise(a)autolog.com<mailto:philippe.hurtubise@autolog.com> E-mail sent at: Thu, 02 Nov 2017 06:15:18 -0400 -- Observium Professional 17.9.8841<http://www.observium.org>

2 2

Hot Backup of Observium database possible?
by Vikas Kumar 02 Nov '17

02 Nov '17

Hi all, Is it possible to take hot backup of observium database? Also if the observium server crashes unexpectedly will we be able to recover it? Thanks -- <http://moodi.org/> *Vikas Kumar | ** Hospitality & PR Coordinator* *Mood Indigo, IIT Bombay* *+91-9694532954 | mailvikasnow(a)gmail.com <mailvikasnow(a)gmail.com>* [image: Facebook] <https://www.facebook.com/vikas.cse.iitb> <https://mailtrack.io/> Sent with Mailtrack <https://chrome.google.com/webstore/detail/mailtrack-for-gmail-inbox/ndnaehg…>

3 2

Juniper SRX1500 firewall questionable CPU OIDs used
by aas029 02 Nov '17

02 Nov '17

Hello, I have Juniper SRX1500 firewalls for which Observium is sending false positive CPU alerts (example included below) based on feedback from Juniper. More specifically, I was told that the OIDs used by Observium to collect CPU information are not the correct ones for this devices in particular. Here are the OIDs that I was told should be used to monitor the data plane CPU usage (instead of the standard OIDs that poll the kernel):.1.3.6.1.4.1.2636.3.39.1.12.1.1.1 Or more specifically for forwarding plane flow (SPU) only: .1.3.6.1.4.1.2636.3.39.1.12.1.1.1.3" Here is an Observium alert example: Alert Juniper Firewall CPU Usage is over 40%! Entity FPC: FEB @0/*/* Conditions processor_usage gt 40 (49) Metrics processor_usage = 49 Duration 4m 19s (2017-10-22 17:22:53) Device Device host.mine Hardware SRX1500 Operating System Juniper JunOS 15.1X49-D50.3 Internet Router Location lab Uptime 27 days, 12h 3m 4s The above alert is seen several times a day per device. I'm currently running version 17.10.8921 (Linux 2.6.32-642.13.1.el6.x86_64 [amd64]) but have seen this with different frequencies on all other versions I had. Appreciate any information on potential fix or workaround or feedback on the Juniper response. Thanks,Al.

3 2

Vpn specific graphs not showing after installing Unix agent
by Vikas Kumar 31 Oct '17

31 Oct '17

Hi I have installed observium Unix agent into my von server and enables the openvpn script at server but still no graph like "no of users active on vpn" is showing up in observium web interface? Please help. Thanks

2 1

deleting device with "delete RRD" options - doesnt delete RRD files itself
by Edvinas K 31 Oct '17

31 Oct '17

Hello, We're using subscriber edition Observium 17.10.8930 (stable) <http://www.observium.org/> When i Delete the device with RRD tick ON, the RRD files is still left in RRD dir. Is it a bug? Thanks

2 3

Observium RRD Size cleanup error
by Vikas Kumar 31 Oct '17

31 Oct '17

Hi i am trying to run php rrd.inc.php but i am getting following error please help PHP Fatal error: Uncaught Error: Call to undefined function age_to_unixtime() in /opt/observium/includes/housekeeping/rrd.inc.php:16 Stack trace: #0 {main} thrown in /opt/observium/includes/housekeeping/rrd.inc.php on line 16 -- <http://moodi.org/> *Vikas Kumar | ** Hospitality & PR Coordinator* *Mood Indigo, IIT Bombay* *+91-9694532954 | mailvikasnow(a)gmail.com <mailvikasnow(a)gmail.com>* [image: Facebook] <https://www.facebook.com/vikas.cse.iitb> ‌ <https://mailtrack.io/> Sent with Mailtrack <https://chrome.google.com/webstore/detail/mailtrack-for-gmail-inbox/ndnaehg…>

2 1

Dashboard recent events - 0s
by Fadly Tabrani 31 Oct '17

31 Oct '17

Hi Everyone, Just checking if everyone else experiencing the same thing. All the recent events on my default page shows 0s. I might have misunderstood what the column means; Is it supposed to indicate how long ago the event occured? [image: Inline image 1] Cheers, FT

2 2

Alert check for load averages
by H Box 31 Oct '17

31 Oct '17

Hi Devs, On 02-02-2017 i send a request to add the option for creating alerts for load averages into observium. The anwer we get back from Tom was: Hi H, > This is currently not possible, as the load average is not linked to a > specific entity and as such not a metric to alert on (yet) ... > Tom When this function will be implemented into observium? Thanks a lot for your information. With kind regards, Remco

1 1

Syslog
by Philippe Hurtubise 30 Oct '17

30 Oct '17

Hi, How can I empty or delete Syslog showing up. I leaves all category during my tests and I have 45k logs during the week end. I tried a maintenance but it didn't delete anything. Thanks Philippe Hurtubise Administrateur réseau / Network administrator [Autolog logo Signature] T: 450.434.8389 ext. 354 F: 450.434.8395 1240 Michèle-Bohec, Blainville, QC, Canada J7C 5S4 www.autolog.com<http://www.autolog.com/> [9501_logo_30ans_Signature]

2 2

VM or Iron
by Vlad Kratsberg 30 Oct '17

30 Oct '17

Hi Everyone, We have been running a VM on Iron box for a few years and now have been noticing slowdowns in performance ( longer poll times, choppy graphs ). We are thinking of moving observium to VM. In your experience, what do you think is better way to run observium on a VM or Iron ? What are the pros and cons ? Thank you for your responses.

2 1

VMs view?
by Ben Filippelli 30 Oct '17

30 Oct '17

Hi all, just curious do I need the pro version in order to see vms on esx servers? I see in the log for the esx host its collecting vm-agent data or at least showing it, but there is nowhere I can 'see' the vms that I can find. Im wondering if its just a matter of upgrading to the pro ... Thanks

2 1

Weathermap for observium
by Edvinas K 30 Oct '17

30 Oct '17

I’ve moved weathermap to new instalation of observium, and i can’t run the map-poller, i get this error: /opt/observium/html/weathermap/map-poller.php PHP Fatal error: require_once(): Failed opening required ‘random_compat/random.php’ (include_path=’/libs/pear:/libs:.:/usr/share/pear:/usr/share/php’) in /opt/observium/includes/definitions.inc.php on line 160 maybe you can how i can cope with this ? Thanks

1 1

SNMP not working in fedora 22
by Vikas Kumar 27 Oct '17

27 Oct '17

i have installed net-snmp in fedora 22 and here is my config at /etc/snmp/snmpd.conf When i do snmpwalk or snmpget on host it displays correct reults but when i try to add device in observium it says device timeout please help When i use the same snmp configuration file in ubuntu 16.04 i am able to add device in observium ############################################################################### # # EXAMPLE.conf: # An example configuration file for configuring the Net-SNMP agent ('snmpd') # See the 'snmpd.conf(5)' man page for details # # Some entries are deliberately commented out, and will need to be explicitly activated # ############################################################################### # # AGENT BEHAVIOUR # # Listen for connections from the local system only #agentAddress udp:127.0.0.1:161 # Listen for connections on all interfaces (both IPv4 *and* IPv6) agentAddress udp:161,udp6:[::1]:161 ############################################################################### # # SNMPv3 AUTHENTICATION # # Note that these particular settings don't actually belong here. # They should be copied to the file /var/lib/snmp/snmpd.conf # and the passwords changed, before being uncommented in that file *only*. # Then restart the agent # createUser authOnlyUser MD5 "remember to change this password" # createUser authPrivUser SHA "remember to change this one too" DES # createUser internalUser MD5 "this is only ever used internally, but still change the password" # If you also change the usernames (which might be sensible), # then remember to update the other occurances in this example config file to match. ############################################################################### # # ACCESS CONTROL # # system + hrSystem groups only view systemonly included .1.3.6.1.2.1.1 view systemonly included .1.3.6.1.2.1.25.1 # Full access from the local host #rocommunity public localhost # Default access to basic system info rocommunity iitb default # -V systemonly # rocommunity6 is for IPv6 rocommunity6 public default -V systemonly # Full access from an example network # Adjust this network address to match your local # settings, change the community string, # and check the 'agentAddress' setting above #rocommunity secret 10.0.0.0/16 # Full read-only access for SNMPv3 rouser authOnlyUser # Full write access for encrypted requests # Remember to activate the 'createUser' lines above #rwuser authPrivUser priv # It's no longer typically necessary to use the full 'com2sec/group/access' configuration # r[ow]user and r[ow]community, together with suitable views, should cover most requirements ############################################################################### # # SYSTEM INFORMATION # # Note that setting these values here, results in the corresponding MIB objects being 'read-only' # See snmpd.conf(5) for more details sysLocation Ubuntu 16.04 Test VM in Server sysContact Vikas Kumar<vikask(a)iitb.ac.in> # Application + End-to-End layers sysServices 72 # # Process Monitoring # # At least one 'mountd' process proc mountd # No more than 4 'ntalkd' processes - 0 is OK proc ntalkd 4 # At least one 'sendmail' process, but no more than 10 proc sendmail 10 1 # Walk the UCD-SNMP-MIB::prTable to see the resulting output # Note that this table will be empty if there are no "proc" entries in the snmpd.conf file # # Disk Monitoring # # 10MBs required on root disk, 5% free on /var, 10% free on all other disks disk / 10000 disk /var 5% includeAllDisks 10% # Walk the UCD-SNMP-MIB::dskTable to see the resulting output # Note that this table will be empty if there are no "disk" entries in the snmpd.conf file # # System Load # # Unacceptable 1-, 5-, and 15-minute load averages load 12 10 5 # Walk the UCD-SNMP-MIB::laTable to see the resulting output # Note that this table *will* be populated, even without a "load" entry in the snmpd.conf file ############################################################################### # # ACTIVE MONITORING # # send SNMPv1 traps trapsink localhost public # send SNMPv2c traps #trap2sink localhost public # send SNMPv2c INFORMs #informsink localhost public # Note that you typically only want *one* of these three lines # Uncommenting two (or all three) will result in multiple copies of each notification. # # Event MIB - automatically generate alerts # # Remember to activate the 'createUser' lines above iquerySecName internalUser rouser internalUser # generate traps on UCD error conditions defaultMonitors yes # generate traps on linkUp/Down linkUpDownNotifications yes ############################################################################### # # EXTENDING THE AGENT # # # Arbitrary extension commands # extend test1 /bin/echo Hello, world! extend-sh test2 echo Hello, world! ; echo Hi there ; exit 35 #extend-sh test3 /bin/sh /tmp/shtest # Note that this last entry requires the script '/tmp/shtest' to be created first, # containing the same three shell commands, before the line is uncommented # Walk the NET-SNMP-EXTEND-MIB tables (nsExtendConfigTable, nsExtendOutput1Table # and nsExtendOutput2Table) to see the resulting output # Note that the "extend" directive supercedes the previous "exec" and "sh" directives # However, walking the UCD-SNMP-MIB::extTable should still returns the same output, # as well as the fuller results in the above tables. # # "Pass-through" MIB extension command # #pass .1.3.6.1.4.1.8072.2.255 /bin/sh PREFIX/local/passtest #pass .1.3.6.1.4.1.8072.2.255 /usr/bin/perl PREFIX/local/passtest.pl # Note that this requires one of the two 'passtest' scripts to be installed first, # before the appropriate line is uncommented. # These scripts can be found in the 'local' directory of the source distribution, # and are not installed automatically. # Walk the NET-SNMP-PASS-MIB::netSnmpPassExamples subtree to see the resulting output # # AgentX Sub-agents # # Run as an AgentX master agent master agentx # Listen for network connections (from localhost) # rather than the default named socket /var/agentx/master #agentXSocket tcp:localhost:705 -- <http://moodi.org/> *Vikas Kumar | ** Hospitality & PR Coordinator* *Mood Indigo, IIT Bombay* *+91-9694532954 | mailvikasnow(a)gmail.com <mailvikasnow(a)gmail.com>* [image: Facebook] <https://www.facebook.com/vikas.cse.iitb> ‌ <https://mailtrack.io/> Sent with Mailtrack <https://chrome.google.com/webstore/detail/mailtrack-for-gmail-inbox/ndnaehg…>

1 0

Re: [Observium] Notifications not working
by Robert Martinez 27 Oct '17

27 Oct '17

Suddenly = 4 days ago, notifiers issue detected yesterday No changes in configs, just rolling upgrades applied config.php // Set up a default alerter (email to a single address) // Alerting $config['email']['default'] = "suddenly(a)suddenly.suddenly"; ## Default alert recipient $config['email']['from'] = "Observium <observium@xxxx>"; $config['email']['default_only'] = FALSE; ## Only use default recipient $config['email']['enable'] = TRUE; ## Enable email alerts $config['email']['backend'] = 'smtp'; array*(*14 enable*=>*true from*=>*Observium <observium@xxxx> default*=>*suddenly(a)suddenly.suddenly default_only*=>*false graphs*=>*true backend*=>*smtp sendmail_path*=>*/usr/sbin/sendmail smtp_host*=>*localhost smtp_port*=>*25 smtp_timeout*=>*10 smtp_secure*=>*null smtp_auth*=>*false smtp_username*=>*null smtp_password*=>*null*)* *DEBUG!CMD[/usr/bin/svn info /opt/observium]CMD EXITCODE[0]CMD RUNTIME[0.0067s]STDOUT[Path: .Working Copy Root Path: /opt/observiumURL: http://svn.observium.org/svn/observium/trunk <http://svn.observium.org/svn/observium/trunk>Relative URL: ^/observium/trunkRepository Root: http://svn.observium.org/svn <http://svn.observium.org/svn>Repository UUID: 61d68cd4-352d-0410-923a-c4978735b2b8Revision: 8927Node Kind: directorySchedule: normalLast Changed Author: adamaLast Changed Rev: 8927Last Changed Date: 2017-10-25 11:13:20 +0200 (Wed, 25 Oct 2017)* If you need more debug, please point what you need and I'll provide you Thanks in advance

1 0

Re: [Observium] Cisco ASA 9.4(3)6 Remote Access Sessions
by Stef Renders 27 Oct '17

27 Oct '17

CISCO-REMOTE-ACCESS-MONITOR-MIB::crasEmailNumSessions.0 = Gauge32: 0 Sessions CISCO-REMOTE-ACCESS-MONITOR-MIB::crasIPSecNumSessions.0 = Gauge32: 0 Sessions CISCO-REMOTE-ACCESS-MONITOR-MIB::crasL2LNumSessions.0 = Gauge32: 1 Sessions CISCO-REMOTE-ACCESS-MONITOR-MIB::crasLBNumSessions.0 = Gauge32: 0 Sessions CISCO-REMOTE-ACCESS-MONITOR-MIB::crasSVCNumSessions.0 = Gauge32: 64 Sessions Red is actual anyconnect users, green is site-to-sites, the sslvpn/anyconnect user graph seems to be hidden by the wall of clientless vpn (which is the exact negative amount of sslvpn users) Stef Renders Cloud Network Engineer E <mailto:stef.renders@arxus.eu> stef.renders(a)arxus.eu <http://www.arxus.eu/> T +32 3 450 67 89 <http://www.arxus.eu/> www.arxus.eu P 'Be green, keep it on the screen. Please think before you print this e-mail. From: observium [mailto:observium-bounces@observium.org] On Behalf Of Adam Armstrong Sent: woensdag 25 oktober 2017 12:03 To: observium(a)observium.org <mailto:observium@observium.org> Subject: Re: [Observium] Cisco ASA 9.4(3)6 Remote Access Sessions Err i mean : snmpwalk -v2c -c <COMMUNITY> -M mibs/rfc:mibs/cisco -m CISCO-REMOTE-ACCESS-MONITOR-MIB <HOSTNAME> crasEmailNumSessions.0 crasIPSecNumSessions.0 crasL2LNumSessions.0 crasLBNumSessions.0 crasSVCNumSessions.0 crasWebvpnNumSessions.0 Changing the hostname and community. adam. On 2017-10-25 11:02:44, Adam Armstrong < <mailto:adama@observium.org> adama(a)observium.org> wrote: Check the returned data on these devices: snmpwalk -v2c -c public -M mibs/rfc:mibs/cisco -m CISCO-REMOTE-ACCESS-MONITOR-MIB crasEmailNumSessions.0 crasIPSecNumSessions.0 crasL2LNumSessions.0 crasLBNumSessions.0 crasSVCNumSessions.0 crasWebvpnNumSessions.0 (from inside the observium dir) adam. On 2017-10-20 10:41:52, Storer, Darren < <mailto:darren.storer@gmail.com> darren.storer(a)gmail.com> wrote: Hi Stef, Did you manage to resolve the ASA VPN session issue mentioned back in March? The graph below is for AnyConnect (SSL) VPN sessions but seems to display correctly as "Clientless". Thanks for any advice Darren On 15 March 2017 at 08:34, Stef Renders < <mailto:stef.renders@cronos.be> stef.renders(a)cronos.be> wrote: Dear Just FYI This started occurring after 9.4.3 release, and still present as of 9.7.1 All releases pre-9.4.3 do not seem to have this issue, and correctly report 0 clientless vpn (when only using anyconnect sslvpn) Kind regards From: observium [mailto: <mailto:observium-bounces@observium.org> observium-bounces(a)observium.org] On Behalf Of Richard Reitenauer Sent: dinsdag 14 maart 2017 19:43 To: <mailto:observium@observium.org> observium(a)observium.org Subject: [Observium] Cisco ASA 9.4(3)6 Remote Access Sessions I am currently using the latest community edition and looking to go to the professional subscription. With a Cisco ASA 9.4(3)6 and graphing the Remote Access Sessions, I am seeing odd data and it looks like others have had the same issue for a couple years now. I attached a screenshot of what I am seeing. >From Cisco CLI – show vpn-sessiondb anyconnect summary: VPN Session Summary --------------------------------------------------------------------------- Active : Cumulative : Peak Concur : Inactive ---------------------------------------------- AnyConnect Client : 96 : 8582 : 101 : 3 SSL/TLS/DTLS : 96 : 8582 : 101 : 3 >From Observium interface snapshot is attached. Is there any fix for this? Also, can we graph per anyconnect group? Thanks, Rich Reitenauer Sr. Infrastructure Analyst 1 Meridian Blvd, Suite 2C01 Wyomissing, PA 19610 O: 610-373-7999 x1255 <mailto:rreitenauer@ugies.com> rreitenauer(a)ugies.com _______________________________________________ observium mailing list <mailto:observium@observium.org> observium(a)observium.org <https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fpostman.m…> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list <mailto:observium@observium.org> observium(a)observium.org <http://postman.memetic.org/cgi-bin/mailman/listinfo/observium> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

4 3

IPsec tunnel monitor question
by Satish Patel 26 Oct '17

26 Oct '17

we have multiple tunnel on ASA which we are monitoring using observium but in graph its just showing number of Active tunnel is there anyway we can have number of tunnel by IP or peer name so we configure alert if any one of tunnel down and take some action

3 2

[Feature Request] F5 LTM Virtual Server bandwidth reports
by Brian Hostetler 26 Oct '17

26 Oct '17

Any plans to add bandwidth reporting for F5 LTM virtual servers (VS)? For companies with customers using a dedicated VS, this would be a really nice feature, rather than using a pooled port for reporting. Brian

1 0

Notifications not working
by Robert Martinez 26 Oct '17

26 Oct '17

Hello, suddenly notifications stop working at all. No e-mail or Slack transit notifiers work xxxx@xxxxx:/opt/observium$ sudo ./test_alert.php -a 11569 Observium 17.10.8927 Test Alert Notification ##### Software versions ##### o OS Linux 4.4.0-97-generic [amd64] (Ubuntu 16.04) o Apache 2.4.18 o PHP 7.0.22-0ubuntu0.16.04.1 (OPcache: ENABLED) o Python 2.7.12 o MySQL 5.7.20-0ubuntu0.16.04.1 (extension: mysqli 5.0.12-dev) o SNMP NET-SNMP 5.7.3 o RRDtool 1.5.5 ##### Memory Limit ##### o PHP Unlimited ##### MySQL mode ##### o MySQL NO_ZERO_IN_DATE,NO_ZERO_DATE,ERROR_FOR_DIVISION_BY_ZERO,NO_AUTO_CREATE_USER,NO_ENGINE_SUBSTITUTION ##### Charset info ##### o PHP UTF-8 o MySQL utf8 ##### Timezones info ##### o Date Thursday, 26-Oct-17 13:13:45 CEST o PHP +02:00 o MySQL +02:00 o Queueing Notification [81049] o Queueing Notification [81050] With debug flag a lot of these till reach the value Queueing Notification [81050] SQL[SELECT * FROM `notifications_queue` WHERE 1] SQL RUNTIME[0.22802496s] SQL[SELECT `notification_locked` FROM `notifications_queue` WHERE `notification_id` = '5309'] SQL RUNTIME[0.00024700s] SQL[SELECT `notification_locked` FROM `notifications_queue` WHERE `notification_id` = '5310'] SQL RUNTIME[0.00008702s] SQL[SELECT `notification_locked` FROM `notifications_queue` WHERE `notification_id` = '5311'] SQL RUNTIME[0.00007796s] SQL[SELECT `notification_locked` FROM `notifications_queue` WHERE `notification_id` = '5312'] SQL RUNTIME[0.00007796s] Any ideas? Best Regards, Robert

2 1

APC Environmental Bars no longer displaying Health Graphs
by Observium 26 Oct '17

26 Oct '17

Hi all, We have 2 APC environmental management agents which we've been using to monitoring temperature and humidity. We've upgraded to 17.9.8829 (stable) this morning, however the logo for each of these devices has changed to NetBotz, instead of the normal APC one. We've lost all health related graphs, temperature/humidity probes, and all related historic data. The event log lists each of the sensor probes being deleted from the system about 7 hours after the upgrade. Other than the upgrade we've made no changes to the system. We've since rebooted each device, and even deleted and re-added one to see if the ports will get re-polled, but no luck. Anyone else experiencing anything similar? As always, any help is most appreciated J Kind regards, Alex

6 16

Groups naming
by Youssef BENGELLOUN - ZAHR 26 Oct '17

26 Oct '17

4 5

Copy module properties between devices
by Jason Lixfeld 25 Oct '17

25 Oct '17

Hey there, Is there perhaps a knob that can be used to copy device properties from Device > Properties > Modules from one device to another, or better yet, if I create a group of devices, can I have all members of the group inherit the same properties? I’ve looked through the GUI and also through the available CLI scripts looking for some clues, but haven’t found anything, so perhaps there’s no such ability? Thanks!

2 1

After migration of Observium im getting some "Error Drawing Graph" errors
by Edvinas K 25 Oct '17

25 Oct '17

Hello, After migrating observium with old rrds and mysql db to new machine some graphs shows . I got this info in "RRD Command" Performance & Output RRDTool Output: ERROR: opening '/opt/observium/rrd/jaycore02/processor-cpm-22.rrd': Permission denied RRDtool Runtime: 0.012s | Total time: 0.013s RRDTool Command /usr/bin/rrdtool graph /tmp/Te25azzHxCwBa1eS.png -Y --lower-limit 0 --upper-limit 100 --start 1508859557 --end 1508945947 --width 1152 --height 300 -c BACK#EEEEEE00 -c SHADEA#EEEEEE00 -c SHADEB#EEEEEE00 -c FONT#000000 -c CANVAS#FFFFFF00 -c GRID#a5a5a5 -c MGRID#FF9999 -c FRAME#5e5e5e -c ARROW#5e5e5e -R normal --font LEGEND:8:'DroidSansMono,DejaVuSansMono' --font AXIS:7:'DroidSansMono,DejaVuSansMono' --font-render-mode normal -E DEF:usage=/opt/observium/rrd/jaycore02/processor-cpm-22.rrd:usage:AVERAGE DEF:usage_max=/opt/observium/rrd/jaycore02/processor-cpm-22.rrd:usage:MAX DEF:usage_min=/opt/observium/rrd/jaycore02/processor-cpm-22.rrd:usage:MIN DEF:usageX=/opt/observium/rrd/jaycore02/processor-cpm-22.rrd:usage:AVERAGE:start=1508773167:end=1508859557 DEF:usage_maxX=/opt/observium/rrd/jaycore02/processor-cpm-22.rrd:usage:MAX:start=1508773167:end=1508859557 SHIFT:usageX:86390 SHIFT:usage_maxX:86390 AREA:usage_max#c5c5c5 AREA:usage_min#ffffff COMMENT:'Usage Now Avg Max \n' LINE1.25:usage#cc0000:' ' GPRINT:usage:LAST:"%6.2lf%s" GPRINT:usage:AVERAGE:"%6.2lf%s" GPRINT:usage_max:MAX:"%6.2lf%s"\n COMMENT:\n LINE1.25:usageX#666666:'Prev \n' AREA:usageX#99999966: CDEF:usagesmooth=usage,1800,TREND CDEF:usagepredict=586400,-7,1800,usage,PREDICT LINE1:usagepredict#FF00FF::dashes=3 RRDTool Files Used /opt/observium/rrd/jaycore02/processor-cpm-22.rrd What could i do ? Thanks

2 4

observium Archives
by Brian Hostetler 25 Oct '17

25 Oct '17

Are the archives locked? http://postman.memetic.org/pipermail/observium/ <http://postman.memetic.org/pipermail/observium/> <http://postman.memetic.org/pipermail/observium/> <http://postman.memetic.org/pipermail/observium/> *Forbidden* You don't have permission to access /pipermail/observium/ on this server. ------------------------------ *Apache/2.4.18 (Ubuntu) Server at postman.memetic.org <http://postman.memetic.org> Port 80* Brian

2 1

Status Map
by Kris Kirkland 25 Oct '17

25 Oct '17

Is there any recommendations for a "Status Map" that is more like Nagvis? We are in the process of moving all our alert checks from Icinga to observium and would like a more robust solution than the current overview map for our operations center display. -- Kris Kirkland ~ K5KRK 2B1ASK1 - http://goo.gl/5bU4F0

1 0

Cisco ASA 9.4(3)6 Remote Access Sessions
by Richard Reitenauer 25 Oct '17

25 Oct '17

I am currently using the latest community edition and looking to go to the professional subscription. With a Cisco ASA 9.4(3)6 and graphing the Remote Access Sessions, I am seeing odd data and it looks like others have had the same issue for a couple years now. I attached a screenshot of what I am seeing. >From Cisco CLI - show vpn-sessiondb anyconnect summary: VPN Session Summary --------------------------------------------------------------------------- Active : Cumulative : Peak Concur : Inactive ---------------------------------------------- AnyConnect Client : 96 : 8582 : 101 : 3 SSL/TLS/DTLS : 96 : 8582 : 101 : 3 >From Observium interface snapshot is attached. Is there any fix for this? Also, can we graph per anyconnect group? Thanks, Rich Reitenauer Sr. Infrastructure Analyst 1 Meridian Blvd, Suite 2C01 Wyomissing, PA 19610 O: 610-373-7999 x1255 rreitenauer(a)ugies.com<mailto:rreitenauer@ugies.com>

4 4

Device taking > 5 minutes to poll
by Jason Lixfeld 24 Oct '17

24 Oct '17

Hey all, I’ve got a device (Zhone MXK-F) with over 10,000 ports on it, and Observium is taking well over 5 minutes to poll it (upwards of 15 minutes, actually). While there isn’t a definition specifically for MXK-F, it’s getting detected as MXK. os.inc.php is setting max-rep 50, so it’s at least trying to bulk walk, but I don’t know if it’s actually working. Overriding to max-rep 100 doesn’t have an affect on the polling time. So, I guess my question is whether or not I’m on the right track in assuming that this issue is likely that of bulk walk on this device, or possibly some other issue, and how would I determine one way or the other? If it’s something that I can pinpoint, I can throw it back to the vendor to fix. From the digging I’ve done so far, all other poller processes called from poller-wrapper complete in under 5 minutes, so I’m fairly certain that this issue is one of the device, not Observium. But, to be thorough, I moved my database and RRD storage over to local SSDs, and also enabled rrdcached - all that to ensure I didn’t have any I/O issues. /pollerlog/view=devices indicates that it’s just the one device that has high timing (although other devices of the same type are spots 2-7 on the top 10 list high timers, but none is over 300 seconds except for this guy). root@monitor:/home/jlixfeld# /opt/observium/poller.php -VV Observium 17.9.8837 ##### Software versions ##### o OS Linux 3.16.0-4-amd64 [amd64] (Debian 8 (jessie)) o Apache 2.4.10 o PHP 5.6.30-0+deb8u1 (OPcache: DISABLED) o Python 2.7.9 o MySQL 5.5.55-0+deb8u1 (extension: mysqli 5.5.55) o SNMP NET-SNMP 5.7.2.1 o RRDtool 1.4.8 (rrdcached 1.4.8: unix:/opt/observium/rrdcached.sock) ##### Memory Limit ##### o PHP Unlimited ##### MySQL mode ##### o MySQL ##### Charset info ##### o PHP UTF-8 o MySQL utf8 ##### Timezones info ##### o Date Monday, 02-Oct-17 12:55:15 EDT o PHP -04:00 o MySQL -04:00 root@monitor:/home/jlixfeld# Thanks all!

5 11

Observium migration
by Edvinas K 24 Oct '17

24 Oct '17

Hello, I freshly installed Observer community edition. Now i need to migrate all information from old mashine to new one. I'm ready to move these things from old mashine to newone: 1)RRD Folder 2)Mysql db 3)Weathermap configuration with existing interface number (requirements is that they would be left the same). So everything should be Ok, but i noticed in older mashine i see in config.php the db configuration is without "$config['db_extension'] = 'mysqli';" like in new one. Will it's possible to get any problem because of that ? Thanks.

2 1

Location list cutted
by El Coyote 24 Oct '17

24 Oct '17

Hi all, I've noticed that if you have a lot of locations you can't see all of them because list in menu is not scrollable. I've about 45 locations and I can't see (and select) last 10.. Thanks

1 0

Session lost
by Mirditor Kuçaj 24 Oct '17

24 Oct '17

Hello Weve had for quite some time problems with our Observium logins. We cant stay for more than a few seconds logged in. We have different users each with their own user/pass and the issue is the same to all of them. Realtime port monitoring is impossible because we cant stay logged in for more than 10 seconds as it says: Cant get data about port xx .. and than we have to log in again and again.. Can you help us troubleshoot this problem and fix it? We tried http://jira.observium.org/browse/OBS-748 Observium 17.9.8859 (25th September 2017) OS Linux 2.6.32-573.26.1.el6.x86_64 [amd64] (CentOS 6.7) Apache 2.2.15 (CentOS) PHP 7.0.6 Python 2.6.6 MySQL 5.1.73 (extension: mysqli 5.1.73) SNMP NET-SNMP 5.5 RRDtool 1.3.8 Thx Mirditor Kuçaj Backbone Network Director <mailto:miri@abissnet.al> miri(a)abissnet.al Abissnet Sh.a. +355 69 60 91 364 +355 (0)44 300 003 Ext 139 Rr. Ismail Qemali, Pallati Abissnet, Tiranë <http://www.abissnet.al/> www.abissnet.al <https://www.facebook.com/Abissnet> <https://plus.google.com/u/0/+AbissnetalISP> <https://www.linkedin.com/profile/view?id=AAIAABqLWRAB88ljU6t8b67oVm8PAlvPrh mPybE&trk=nav_responsive_tab_profile%20>

2 3

Graphing OSPF neighbour count?
by Brandwatch NOC 23 Oct '17

23 Oct '17

Hi All, Love Observium, thanks! We had an issue on Friday with an OSPF adjacency; we didn't see it for various reasons and the logs on the device aged out quickly so we don't have a historical on when it came back. We will extend the log depth and possibly ship logs centrally but that doesn't help us on this occasion. This led to me digging around in Observium to see if it had captured the neighbour flapping. The routing tab is great and even shows neighbour count, but it doesn't seem to be graphed (unless I'm overlooking it). Is this something that I could turn on somehow? Many thanks! Chris

2 3

Webhook MS Teams not working
by Epco Dijk 22 Oct '17

22 Oct '17

Hi, I have an alert setup to notify via MS Teams. However it doesn’t arrive. When I run ./test_alert.php -dd -a 327 the webhook gives a 400 Bad Request Testing with the same webhook with curl returns a “1” curl -H "Content-Type: application/json" -d "{\"text\": \"Hello World\"}" https://outlook.office.com/webhook/xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 1 [cid:image001.png@01D3435E.E47C3B10] But Observium shows this: SQL RUNTIME[0.00041604s] o Notifying [webhook] Microsoft Teams: {"url":"https:\/\/outlook.office.com\/webhook\/xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx"} REQUEST[https://outlook.office.com/webhook/xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx… REQUEST STATUS[FALSE] REQUEST RUNTIME[0.1904s] RESPONSE CODE[400 Bad Request] RESPONSE[ ] > $http_response_header /opt/observium/includes/common.inc.php:3585 array( [0] => string(24) "HTTP/1.1 400 Bad Request" [1] => string(23) "Cache-Control: no-cache" [2] => string(16) "Pragma: no-cache" [3] => string(18) "Content-Length: 28" [4] => string(39) "Content-Type: text/plain; charset=utf-8" [5] => string(11) "Expires: -1" [6] => string(48) "request-id: xxxxxxxxxxxxxxxxxxxxxxxxxxx" [7] => string(68) "X-CalculatedBETarget: AM5PR0102MB2723.eurprd01.prod.exchangelabs.com" [8] => string(24) "X-BackEndHttpStatus: 400" [9] => string(27) "X-AspNet-Version: 4.0.30319" [10] => string(55) "X-CafeServer: AM5PR0201CA0013.EURPRD02.PROD.OUTLOOK.COM" [11] => string(27) "X-BEServer: AM5PR0102MB2723" [12] => string(21) "X-Powered-By: ASP.NET" [13] => string(27) "X-FEServer: AM5PR0201CA0013" [14] => string(100) "X-MSEdge-Ref: Ref A: XXXXXXXXXX9787B468 Ref B: AMSEDGE0313 Ref C: 2017-10-12T10:38:38Z" [15] => string(35) "Date: Thu, 12 Oct 2017 10:38:38 GMT" [16] => string(17) "Connection: close" ) Epco Dijk Systems Administrator Northpool B.V. 3e Binnenvestgracht 23 N 2312 NR Leiden The Netherlands Tel: +31 (0)88 2400300 Fax: +31 (0)88 2400399 E-mail: epco.dijk(a)northpool.nl Web: www.northpool.nl [Logo Northpool] This message and any attachments (the "message") are confidential and intended solely for the addressees. If you are not the addressee indicated in this message or if this message has been addressed to you by error, you may not copy or deliver this message to anyone but destroy it and kindly notify the sender by reply email. Any unauthorised use or dissemination is prohibited. E-mails are susceptible to alteration. Northpool bv shall not be liable for the message if altered, changed or falsified.

4 11

moving observium from one machine to another
by Edvinas K 20 Oct '17

20 Oct '17

Hello, we're using subscription version of Observium. Time has come to move the Observium from old to new mashine, do is't possible to to just copy /opt/observium from old mashine to new and make it work with all the history of graphs saved. ? Also we're using weathermap, is it possible by doing this way (just moving Observium) to save weathermap interface numbers ? Thanks

2 2

Syslog Integration
by Philippe Hurtubise 20 Oct '17

20 Oct '17

Hi, I am trying to configure syslog integration to send syslog from Windows server to Obeservium. I followed instruction on this page http://docs.observium.org/syslog/. But at the bottom of the page I am not sure what to do. Syslog-ng Make sure these options are set : options { chain_hostnames(0); keep_hostname(1); use_dns(no); }; Use this as destination in syslog-ng.conf, change syslog.php path to match yours source s_net { udp(); }; destination d_observium { program("/opt/observium/syslog.php" template ("$HOST||$FACILITY||$LEVEL_NUM||$LEVEL||$TAG||$YEAR-$MONTH-$DAY $HOUR:$MIN:$SEC||$MSG||$PROGRAM\n") template-escape(yes)); }; log { source(s_net); destination(d_observium); }; Where do I add options mentioned, where is the syslog-ng.conf file and where do I add sources section. Thanks

2 2

Re: [Observium] Webhook MS Teams not working
by Epco Dijk 19 Oct '17

19 Oct '17

Hi Tom, Thanks for your support. I will update my installation and let you know the results. To come back to your earlier question. The MS Teams webhook is indeed a string like this: https://outlook.office.com/webhook/35efe6c3-7319-485a-afd3-1865ffa3c4ed@3b8… I'm a bit struggling with spamfilters and this list to properly receive your replies. I only get a digest. So that's why I reply like this. KR, Epco Message: 8 Date: Thu, 19 Oct 2017 00:39:13 +0200 From: Tom Laermans <tom.laermans(a)powersource.cx> To: observium(a)observium.org Subject: Re: [Observium] Webhook MS Teams not working Message-ID: <e7d7f221-e294-2ba9-32d5-9920bcd86d46(a)powersource.cx> Content-Type: text/plain; charset="windows-1252"; Format="flowed" There's a MS Teams transport in the repository now - not fully tested. Comments welcome! Tom Epco Dijk Systems Administrator Northpool B.V. 3e Binnenvestgracht 23 N 2312 NR Leiden The Netherlands Tel: +31 (0)88 2400300 Fax: +31 (0)88 2400399 E-mail: epco.dijk(a)northpool.nl Web: www.northpool.nl [Logo Northpool] This message and any attachments (the "message") are confidential and intended solely for the addressees. If you are not the addressee indicated in this message or if this message has been addressed to you by error, you may not copy or deliver this message to anyone but destroy it and kindly notify the sender by reply email. Any unauthorised use or dissemination is prohibited. E-mails are susceptible to alteration. Northpool bv shall not be liable for the message if altered, changed or falsified.

1 1

Custom OID Juniper COS queue
by Peter Derissen 18 Oct '17

18 Oct '17

Hi all, Im trying to figure out how to build a custom oid. It doesn't matter how I put the info into the add custom oid fields. It just won't draw a graph and also doesn't give a decent response. Any idea how I should do this? [cid:image001.png@01D34828.D0C54FC0] I found this info on twitter: I use JUNIPER-COS-MIBS. OID : jnxCosQstatQedPkts (1.3.6.1.4.1.2636.3.15.4.1.3.ifindex.queue) for monitor pkts in queue jnxCosQstatQedBytes (1.3.6.1.4.1.2636.3.15.4.1.5.ifindex.queue) for monitor bytes in queue :-) Met vriendelijke groet, Peter Derissen Eurofiber Nederland Network Engineer Safariweg 25-31 +31 (0)6 11587110 3605 MA Maarssen [EF-logo_rood_RGB -handtekening]<http://www.eurofiber.nl/> Volg ons op Twitter<https://twitter.com/Eurofiber> | Linkedin<https://www.linkedin.com/company/eurofiber> | Youtube<https://www.youtube.com/user/Eurofibergroup> [cid:image002.png@01D225FF.7ECDA420]<http://bit.ly/2eaBgRh> ******** IMPORTANT NOTICE ******** This e-mail (including any attachments) may contain information that is confidential or otherwise protected from disclosure and it is intended only for the addressees. If you are not the intended recipient, please note that any copying, distribution or other use of information contained in this e-mail (and its attachments) is not allowed. If you have received this e-mail in error, kindly notify us immediately by telephone or e-mail and delete the message (including any attachments) from your system. Please note that e-mail messages may contain computer viruses or other defects, may not be accurately replicated on other systems, or may be subject of unauthorized interception or other interference without the knowledge of sender or recipient. Eurofiber only sends and receives e-mails on the basis that Eurofiber is not responsible for any such computer viruses, corruption or other interference or any consequences thereof. Eurofiber Nederland B.V. is registered in the Chamber of Commerce of Amsterdam with number 34134377, VAT number NL 8088.51.524 B01.

3 4

Default values temperature sensors, min/max warnings
by Svensson Fredrik A 18 Oct '17

18 Oct '17

Hi there, where does the default values come from, for example this: [cid:image001.png@01D347F3.7C3B9160] Is it possible to change them, for lets say all my 3650:s, without doing it on every device? Regards Fredrik

2 1

Gettign SVN timeout error
by Josh Bierman 18 Oct '17

18 Oct '17

Hi All, I am getting an error when I go to update. Server sent unexpected return value (408 Request Timeout) in response to OPTIONS request for 'http://svn.observium.org/svn/observium/trunk' I am looking for suggestions on troubleshooting this. I have tried: Making an outgoing rule on the firewall from my Observium server to http://svn.observium.org. Opening outgoing (and therefore, returning) Ports: 80, 443, 21, 22, 8080, 3690 None of that has made a difference. I can ping the svn server from my Observium machine, I can browse to the web page, my login credentials are correct..... ideas? Joshua Bierman

3 5

regexp based on sysName
by Skyler Blumer 17 Oct '17

17 Oct '17

Is there a way to set regex config based on policy or groups? I'd like to do something like .. if (hostname != "example_host"){ $config['bad_ifalias_regexp'][] = "/^$/"; }

1 1

Tables in the Observium DB
by Eric Kollmann 16 Oct '17

16 Oct '17

First, I just took over our install of this, wasn't involved in the initial setup of observium and I understand the piece I'm asking about is not part of observium, just uses the data it collects and I want to verify if structure has changed since it was released or if there is something incorrectly setup with our system. I'm looking to build out graphviz maps with the data observium has gathered, specifically using: https://github.com/kedare/observium_map_generator Going through their code, it queries the db for the links table and fails. Looking at the database I have a neighbours table, but not links. Google search I see links table discussed back in 2014, but nothing much recently. So, did the links table go away in newer versions, or is the fact that the table is missing an issue with our setup? If it is supposed to be there and missing, I'll work on figuring that out next, if it did just go away I just want to verify that. Thanks

4 11

Cisco device hardware name not showing after IOS upgrade
by Youssef BENGELLOUN - ZAHR 16 Oct '17

16 Oct '17

2 8

Re: [Observium] New install, Alert Checker not triggered
by J Green 14 Oct '17

14 Oct '17

Hello there: Just built a new system w/ CE version 17.9 on Centos 7.2 . When I create/run the following Alert Check, it shows as 'OK' for my devices: processor_usage greater 90 * * When I go to a device and view graphs, it shows a device w/ 100% CPU utilization No errors in logs/db.log. Is my syntax incorrect? Thank you.

4 8

Juniper SRX system uptime value
by Youssef BENGELLOUN - ZAHR 12 Oct '17

12 Oct '17

6 22

Monitoring interface flaps and PSU count
by Edvinas K 10 Oct '17

10 Oct '17

Hello, is it possible to create an checker rule to monitor interface FLAPS and Power PSU count ?

1 0

MIB additions
by Tripp Lite 09 Oct '17

09 Oct '17

Hello, I have some newer Tripp Lite products that I have in my network that utilize two additional MIB's in the software. How can I get these added to the platform? The MIB's are TRIPPLITE.MIB and TRIPPLITE-PRODUCTS.MIB Regards, Eric C.

3 6

Alert on package update
by Simon Mousey Smith 08 Oct '17

08 Oct '17

Hi all Not sure if this is possible or maybe a feature request but here we go Is it possible for observium to email on a package update? A few machines auto update for Plesk and would be nice to be notified when they get updated I can see in observium in the Eventlog of the devices Package updated: plesk-php70-fpm (x86_64) from 7.0.23-centos6.17090111 to 7.0.24 Regards Simon

2 2

Bogus alerts since last CE update
by Musall, Maik 06 Oct '17

06 Oct '17

Hi, on Sept 28th I updated one installation to the new CE release (17.9.0). Since then, Observium keeps sending me interface down/up alerts for every single port on every single switch and router, once every day between 11:20 am and 11:35 am (a bunch every 5 minutes). The alerts look like this: They serve to notify me if anyone connects or disconnects something in my absence. That worked well for a year or so, until I did this update. Now I get 114 emails every day at the same time. What could be the cause, and how can I solve that? Maik

3 3

Poller wrapper history stopped working
by Silvio del Val Hinojal 06 Oct '17

06 Oct '17

Hello, We have upgraded Observium from CE to Pro version following upgrade document, we are now running 17.9.8859 (stable) version and, since then, global "Poller Wrapper history" stopped working. Now it shows "- nan" in all fields. This is what it shows now: [cid:image002.png@01D33E9A.3B2E1D80] Any hint? Regards, Silvio [cid:image001.png@01D03B1C.E8E96F80]<http://www.pandasecurity.com/spain/> Silvio del Val Systems Engineer - Panda Security +34 944 343 728 silvio.delval(a)pandasecurity.com<mailto:silvio.delval@pandasecurity.com> pandasecurity.com<http://www.pandasecurity.com/> This e-mail contains confidential information owned by Panda Security. Any such copy, or use, or distribution or disclosure of its contents is strictly forbidden. Please notify us immediately at our phone number (+34 94 425 11 00) if you receive this e-mail and are not its consignee, and then delete this message from your system without copying it, distributing it, or disclosing its contents P Before printing this message, please make sure it is really necessary

2 1

Multiple mailing options
by Franks Andy (IT Technical Architecture Manager) 06 Oct '17

06 Oct '17

Hi all, We have a scenario where we'd like, for certain alerts, to not only send via the default mail settings but also to forward to an external sms portal. This particular portal is fairly simple and works via sending an email to a certain domain with a phone number prefix. We'd need to use different mail settings for this purpose though and I was wondering if someone could think of the best way to do this. I can't really find many examples for the external script or web hook transport methods, and ideally we'd be able to do most of the configuration and filtering directly within observium rather than doing the messaging logic elsewhere. Thanks Andy

2 1

Alarm on VLAN?
by Ryan, Spencer 05 Oct '17

05 Oct '17

Hey Guys, Is there any way to write an alert check to alarm if a VLAN is seen on a port (either access or trunk?). We have a few "untrusted" networks that we want to know if they get stuck on a trunk somewhere they shouldn't be. Thanks! Spencer Ryan | Senior Systems Administrator | sryan(a)arbor.net<mailto:sryan@arbor.net> Arbor Networks +1.734.794.5033 (d) | +1.734.846.2053 (m) www.arbornetworks.com<http://www.arbornetworks.com/>

2 1

syslog not working after observium rsyslog server configuration
by Vikas Kumar 05 Oct '17

05 Oct '17

I have observium CE addition and i recently tried for syslog integration on it as given here http://docs.observium.org/syslog/ I am able to see syslog messages in observium UI but unfortunately my syslog messages of observium machine itself are not getting logged to /var/log/syslog . please some one help me here. These are my configuration files as attached with this post /etc/rsyslog.conf ################# $ModLoad imudp $UDPServerRun 514 module(load="imuxsock") # provides support for local system logging module(load="imklog") # provides kernel logging support #module(load="immark") # provides --MARK-- message capability # provides UDP syslog reception #module(load="imudp") #input(type="imudp" port="514") # provides TCP syslog reception #module(load="imtcp") #input(type="imtcp" port="514") # Enable non-kernel facility klog messages $KLogPermitNonKernelFacility on ########################### #### GLOBAL DIRECTIVES #### ########################### # # Use traditional timestamp format. # To enable high precision timestamps, comment out the following line. # $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat # Filter duplicated messages $RepeatedMsgReduction on # # Set the default permissions for all log files. # $FileOwner syslog $FileGroup adm $FileCreateMode 0640 $DirCreateMode 0755 $Umask 0022 $PrivDropToUser syslog $PrivDropToGroup syslog # # Where to place spool and state files # $WorkDirectory /var/spool/rsyslog # # Include all config files in /etc/rsyslog.d/ # $IncludeConfig /etc/rsyslog.d/*.conf $DebugFile /var/log/rsyslogdebug.txt $DebugLevel 1 ----------------------------------------------------------------------------------------------------- Another observium config file is located at /etc/rsyslog.d/30-observium.conf at it contains: #--------------------------------------------------------- #send remote logs to observium template(name="observium" type="string" string="%fromhost-ip%||%syslogfacility%||%syslogpriority%||%syslogseverity%||%syslogtag%||%$year%-%$month%-%$day% %timereported:8:25%||%msg%||%programname%\n") $ModLoad omprog Module (load="imudp") # rsyslog Input Modules input(type="imudp" port="514" ruleset="observium") # rsyslog RuleSets ruleset(name="observium") { action(type="omprog" binary="/opt/observium/syslog.php" template="observium") } *.* stop #--------------------------------------------------------- i have added a new line Module (load="imudp") apart from the original given here at http://docs.observium.org/syslog/ But now when i do tail -f /var/log/syslog i get this : Oct 5 15:45:01 testnet-PC CRON[3000]: (root) CMD ( /opt/observium/discovery.php -h new >> /dev/null 2>&1) Oct 5 15:45:01 testnet-PC CRON[3001]: (root) CMD ( /opt/observium/poller-wrapper.py 4 >> /dev/null 2>&1) Oct 5 15:47:19 testnet-PC rsyslogd: [origin software="rsyslogd" swVersion="8.16.0" x-pid="2898" x-info="http://www.rsyslog.com"] exiting on signal 15. and nothing more events are shown here. Please someone help how do i get my usual syslog messages back on observium machine. Thanks Regards, Vikas kumar IIT Bombay India -- <http://moodi.org/> *Vikas Kumar | ** Hospitality & PR Coordinator* *Mood Indigo, IIT Bombay* *+91-9694532954 | mailvikasnow(a)gmail.com <mailvikasnow(a)gmail.com>* [image: Facebook] <https://www.facebook.com/vikas.cse.iitb> <https://mailtrack.io/> Sent with Mailtrack <https://chrome.google.com/webstore/detail/mailtrack-for-gmail-inbox/ndnaehg…>

2 1

Scaling Observium with distributed pollers
by Markus Klock 05 Oct '17

05 Oct '17

Hi guys, I wrote a blogpost on how you can scale Observium to handle ridiculously large deployments, you will find it here: http://blog.best-practice.se/2017/10/scaling-observium-horizontally.html And comments or feedback is most welcome! /Markus

3 3

VPN site-to-site monitoring by name
by Satish Patel 04 Oct '17

04 Oct '17

I have posted on JIRA http://jira.observium.org/browse/OBS-2438 But just wonder if anyone has any solution for this issue, we have many site-to-site tunnel and in observium its just showing count but it would be good if it shows list of tunnel by name so easy to identify down tunnel and alert.

2 3

Graphs not rendering correctly
by Mal Evans 04 Oct '17

04 Oct '17

Hi all, Seem to be having a problem with the graphs on my new install (CE). See the example below: As you can see there are regular gaps in the display. I am wondering if this might have something to do with a polling cycle etc? not sure where to start investigating so any suggestions are welcome. As far as I can tell every graph shows similar behaviour. Cheers Mal

3 4

p2p radio detection
by Joey Stanford 04 Oct '17

04 Oct '17

Howdy, We noticed not that long ago that Ubiquity devices gained p2p radio detection. Is there any consideration for Ubutiks (Ubiquity RF + Microtik routerboard)? We have a number of these and the device_state array contains the p2p radio info just like the Ubiquity radios do. Discovery put the ubutiks into the network category like a normal mikrotik. We’ve been changing them over by hand to wireless for categorization. Thanks, Joey

1 0

Monitor Exchange 2016
by Juan Carlos Rodriguez 03 Oct '17

03 Oct '17

Hello. I am new to observium and I would like to know how can I monitor an exchange 2016 server via WMI?, I can pull regular SNMP data from the server. thanks for your help Juan

1 0

Juniper SRX4200 and transceivers sensors
by Youssef BENGELLOUN - ZAHR 01 Oct '17

01 Oct '17

2 1

Sonus Session Border Controller support
by Ármann Guðjónsson 30 Sep '17

30 Sep '17

Hi Adam Are there any plans to add support for Sonus Session Border Controller ? Best regards Armann

2 1

Feature request: OpenBSD CARP and pf
by Tommy Nevtelen 28 Sep '17

28 Sep '17

Hi there! I would like to request CARP-MIB and PF-MIB support in Observium. Most importantly show if the CARP interfaces are master or backup. So we can get alerted. Maybe show it in the same way as Cisco ASA Active/Passive or some other better suited as you can have an arbitrary amount of CARP interfaces. And then the ability to graph the statistics from PF-MIB. The MIBs for reference: https://github.com/openbsd/src/tree/master/share/snmp Not sure if this is a lot of work or not though, hope some of it is easy enough :) -- Tommy Nevtelen

1 0

Alerts Frequency
by Kris Kirkland 28 Sep '17

28 Sep '17

Is there an option to keep observium from "obsessing" over an alert? I would like to only alert once on failure and once on recovery, not every time it checks. -- Kris Kirkland ~ K5KRK 2B1ASK1 - http://goo.gl/5bU4F0

1 0

Not getting alert in storage alert checker
by vaibhavkholase41＠gmail.com 28 Sep '17

28 Sep '17

Dear Team , We are stucked with observium in one alert checker issue. We have created alert checker rule as per given in your demo site still we are not able to get any storage alert even if we set this at minimum level. Below is the screenshot for alert checker configuration can you please help us it would be very great for us. One more thing is we are exploring community edition, once this is successfully tested then we will use this in our company . Waiting for your response. Thanks In Advance. Thanks & Regards , Vaibhav Kholase Sent from Mail for Windows 10

3 3

Re: [Observium] Not able to check storage status
by Tom Laermans 28 Sep '17

28 Sep '17

Hi, Please reply to the mailing list instead of directly to me. Also, can you make the image a bit smaller still? I can still read it if I really try... Either way, have you selected the correct entity type? * is not matching any entity so I'd assume not. Tom On 27/09/2017 18:31, vaibhavkholase41(a)gmail.com wrote: > > Dear Team , > > PFB Screenshot for same & I am using community edition of observium. > > Also in config.php I have use as it is option which are defined on > your wiki. > > Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for > Windows 10 > > *From: *Tom Laermans <mailto:tom.laermans@powersource.cx> > *Sent: *Wednesday, September 27, 2017 9:59 PM > *To: *observium(a)observium.org <mailto:observium@observium.org> > *Subject: *Re: [Observium] Not able to check storage status > > How about you show us what you tried (including screenshots) ? > > Tom > > On 27/09/2017 18:00, vaibhavkholase41(a)gmail.com > <mailto:vaibhavkholase41@gmail.com> wrote: > > Hi Team , > > Could you please help in how can I get the alert checker for > storage as I tried it with multiple ways but no luck. > > So requesting you to please suggest is there any nee to update my > config.php which is created by following observium docs. > > Thanks You Team In Advance.. > > Reagards , > > Vaibhav Kholase > > Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> > for Windows 10 > > > > > _______________________________________________ > > observium mailing list > > observium(a)observium.org <mailto:observium@observium.org> > > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >

2 3

Not able to check storage status
by vaibhavkholase41＠gmail.com 27 Sep '17

27 Sep '17

Hi Team , Could you please help in how can I get the alert checker for storage as I tried it with multiple ways but no luck. So requesting you to please suggest is there any nee to update my config.php which is created by following observium docs. Thanks You Team In Advance.. Reagards , Vaibhav Kholase Sent from Mail for Windows 10

2 1

Preferred MTA?
by Joe Brouillette 27 Sep '17

27 Sep '17

Hey all, I've been trying to get Observium to send alerts to my Exchange server. Wireshark on Exchange shows nothing so I just gave up, looked online and found a post from Adam saying to not use SMTP; he recommended using an MTA instead. Does Observium have a preferred MTA? Any to watch out for? Thanks, Joe Brouillette IT Specialist Link Transit 509.664.7643 jobee(a)linktransit.com<mailto:jobee@linktransit.com> [cid:image001.jpg@01D32E19.765EA2D0]<http://www.letsthinklink.org/> "Help reimagine the future of our transit system."

4 4

Transfer account
by Kacper Czerwonka 27 Sep '17

27 Sep '17

Hello. My company wants to renew our subscriptions. Subscriptions are created on account named by my name, surname don't mention about job email. I'm going to change job in next two months and we need to straight it right. Is there possibility to: - change account name, etc. - or transfer subscriptions to new account - or just create new account and by new subscriptions What options do we have? Kacper. ------------------------------------------------------------------------ *mgr inż. Kacper Czerwonka* Inspektor Wydział Informatyki 75-007 Koszalin; Rynek Staromiejski 6-7 Tel.: (+48) 94 348 39 50; Fax (+48) 94 348 88 98 @: kacper.czerwonka(a)um.koszalin.pl <mailto:kacper.czerwonka@um.koszalin.p> www.koszalin.pl

2 1

Commit 8852 breaks graphs
by Jesse Defer 26 Sep '17

26 Sep '17

After updating to 8852 my multi-customoid graphs are broken. Line graphs render but have no devices/data points and stacked graphs return the error image. Rolling back to 8851 shows expected behavior. Jesse

4 5

Adding new device support and collaboration
by 管华 26 Sep '17

26 Sep '17

Hi,Observium Team: I'm a test engineer for Fiberhome, and we currently plan to write files for Fiberhome's network devices in community version software. I was wondering if I could send the files to your team, after you optimized it and added it to later releases to facilitate software upgrades and other user usage. I hope our developers can join you later to develop this software and make it better. About us http://www.fiberhome.com.cn Please reply when you receive it.I'd like to have a talk with you.Thanks… nwos_gh(a)fiberhome.com

1 0

Pandacom DWDM devices
by Andre Geißler 26 Sep '17

26 Sep '17

Hi all Recently we purchased some DWDM devices from Pandacom (SPEED-OTS-5000). Might be interesting for more than us to have them in observium. Is there a way for a non-programmer like me to add those devices? What I can provide are the MIB files. If access to a device is needed for testing I'd like to use my contact at Pandacom Cheers, Andre

5 4

Export Observium Installation
by Chad 20 Sep '17

20 Sep '17

Hey folks, Is there a simple way to export the entire config for the Observium community edition? I'm running the latest 16x version on a dedicated server but would rather switch over to a simplified KVM virtual server. Can someone explain the proper path to accomplish this? Thanks.

2 1

Virtual machines showing lots of duplicates
by Philippe Hurtubise 19 Sep '17

19 Sep '17

Hi, I have 6 ESXi hosts. On one host and only for 1 VM on that host, the VM is showing lots of times in the Virtual machines section. All the others VM on the same host are showing only 1 time. Thanks Philippe Hurtubise Administrateur réseau / Network administrator [Autolog logo Signature] T: 450.434.8389 ext. 354 F: 450.434.8395 1240 Michèle-Bohec, Blainville, QC, Canada J7C 5S4 www.autolog.com<http://www.autolog.com/>

1 1

RRDTool Customisation
by William Hutchins 19 Sep '17

19 Sep '17

Hi All, What could be a silly question - Is there a straightforward switch or option to alter the RRDtool formatting from the default “opposing” format for Upload/Download, to an overlaid format in network traffic graphing? Current opposing format https://ibb.co/kbGcB5 Required Overlaid format https://ibb.co/nGJw4Q I’ve noted the config example in doco, however switching off the opposing view/feature wasn’t immediately clear. Thought I’d ask to see if the devs had a hidden php configuration switch for this, and if not, how others might’ve overcome this? Many thanks, Will

3 2

Issue with Search Function in BGP Sessions
by Gumilar Siegfried 18 Sep '17

18 Sep '17

Hello! I ran into a little issue today. If I am on page two of the BGP session list and search for a remote AS the search always comes up with an empty list. I guess this is caused by the "pageno=2" in the URL: http://x.x.x.x/routing/protocol=bgp/graph=NULL/view=details/pagination=1/pa…... If I remove the pageno=2 section in the URL I get the right result. Regards, Siegfried

1 0

SMS alerts configuration in observium?
by Vikas Kumar 18 Sep '17

18 Sep '17

Dear all, I am trying to configure sms alerts in observium for this my institute has a sms gateway via which i can send messgaes to ant number the API is in this format " http://smsgateway.iitb.ac.in/smsapi/index.php?To=91********&Message=test2 <http://dcmonitor.iitb.ac.in/smsapi/index.php?To=919930547677&Message=test2>" . Now i want to post the notification to this API. So i edited the file /opt/observium/includes/defaults.inc.php as follows: $config['smsbox']['scheme'] = 'http'; // URL scheme, http or https. $config['smsbox']['host'] = 'smsgateway.iitb.ac.in'; // Name of host on which SMSBox is running. $config['smsbox']['port'] = '80'; // Port number on which SMSBox host receives requests. $config['smsbox']['user'] = ''; // SMSBox username. $config['smsbox']['password'] = ''; // SMSBox password. $config['smsbox']['from'] = ''; // Phone number of sender, usually overridden by SMSC. Then i edited the file /opt/observium/includes/alerting/smsbox.inc.php as follows: <?php // Kannel SMSBox documentation: http://kannel.org/download/1.5.0/userguide-1.5.0/userguide.html#AEN4623 $message = $message_tags['ALERT_STATE'] . " " . $message_tags['DEVICE_HOSTNAME'] .": " . $message_tags['ENTITY_NAME'] . "\n" . $message_tags['ALERT_MESSAGE']; $context_data = array ( 'method' => 'GET', 'header' => "Connection: close\r\n" ); $url = sprintf('%s://%s/smsapi/index.php?To=%s&Meassage=%s', $config['smsbox']['scheme'], $config['smsbox']['host'], urlencode($endpoint['phone']),urlencode($message)); $response = get_http_request($url, $context_data); if (strpos($response, "Accepted") || strpos($response, "Queued")) { $notify_status['success'] = TRUE; } else { $notify_status['success'] = FALSE; } unset($message); // EOF But still i am not able to get SMS alerts on my mobile phone. Please note that the SMS gateway has given IP based access to my machine on which observium is runnning so i do not need username and password fileds while posting message to the API. Please help me resolve this issue . Thanks -- <http://moodi.org/> *Vikas Kumar | ** Hospitality & PR Coordinator* *Mood Indigo, IIT Bombay* *+91-9694532954 | mailvikasnow(a)gmail.com <mailvikasnow(a)gmail.com>* [image: Facebook] <https://www.facebook.com/vikas.cse.iitb> ‌

1 0

CentOS 7.4?
by William Bauer 18 Sep '17

18 Sep '17

Anyone upgrade their installation from CentOS7.3 to 7.4? I needed that upgrade on other systems due to some patches that wouldn't be released to 7.3. I've had no issues with 7.4, so I'm wondering if anyone has run into Observium related problems with 7.4? It only came out officially in the last few days, so it may be too early to ask.

4 10

Re: [Observium] observium Digest, Vol 86, Issue 14
by Patricio Hernan Besteiro 16 Sep '17

16 Sep '17

Hi Community, Is it possible to create an alert checker from data gathered by unix-agent? (observium CE) Kind regards, Patricio Hernan Besteiro Unix Systems Administrator IBM Client Innovation Center - Buenos Aires - Argentina E-mail: besteiro(a)ar.ibm.com From: observium-request(a)observium.org To: observium(a)observium.org Date: 15/09/2017 08:00 Subject: observium Digest, Vol 86, Issue 14 Sent by: "observium" <observium-bounces(a)observium.org> Send observium mailing list submissions to observium(a)observium.org To subscribe or unsubscribe via the World Wide Web, visit https://urldefense.proofpoint.com/v2/url?u=http-3A__postman.memetic.org_cgi… or, via email, send a message with subject or body 'help' to observium-request(a)observium.org You can reach the person managing the list at observium-owner(a)observium.org When replying, please edit your Subject line so it is more specific than "Re: Contents of observium digest..." Today's Topics: 1. Edit existing alert (Todd Hank) 2. Re: Edit existing alert (Adam Armstrong) 3. Re: Edit existing alert (Todd Hank) 4. Re: Edit existing alert (Adam Armstrong) 5. Re: Edit existing alert (Todd Hank) 6. Re: Edit existing alert (Adam Armstrong) 7. Re: Devices (Philippe Hurtubise) 8. Re: Geolocation detection improvement (Pico Leto) ---------------------------------------------------------------------- Message: 1 Date: Thu, 14 Sep 2017 13:57:57 +0000 From: Todd Hank <Todd.Hank(a)i-car.com> To: 'Observium' <observium(a)observium.org> Subject: [Observium] Edit existing alert Message-ID: <8B4AAF1CA3AA1B478B77F99F2952ECCD25618483(a)HERMES01.i-car.org> Content-Type: text/plain; charset="utf-8" I am certainly a newbie yet and I am playing around with alerts. I created a couple alerts that I would like to edit. I do not see a way to edit them. Any Advice? Thanks, Todd Hank Senior Network Administrator (920) 749-0444 Ext. 128 Todd.Hank(a)i-car.com STAY CONNECTED: [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ]< https://urldefense.proofpoint.com/v2/url?u=https-3A__www.facebook.com_icare… > [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ] < https://urldefense.proofpoint.com/v2/url?u=https-3A__www.twitter.com_i-5Fca… > [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ] < https://urldefense.proofpoint.com/v2/url?u=https-3A__www.instagram.com_icar… > [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ] < https://urldefense.proofpoint.com/v2/url?u=https-3A__www.linkedin.com_compa… > [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ] I-CAR.com< https://urldefense.proofpoint.com/v2/url?u=http-3A__www.i-2Dcar.com&d=DwIGa… > | RTS< https://urldefense.proofpoint.com/v2/url?u=http-3A__rts.i-2Dcar.com_&d=DwIG… > | Collision Reporter Magazine< https://urldefense.proofpoint.com/v2/url?u=https-3A__www.i-2Dcar.com_collis… > [ https://urldefense.proofpoint.com/v2/url?u=http-3A__nebula.i-2Dcar.com_i-2D… ]< https://urldefense.proofpoint.com/v2/url?u=https-3A__www.i-2Dcar.com&d=DwIG… > ________________________________ This message, including any attachments, is intended only for the use of the individual or entity to which it is addressed, and may contain confidential information. Please do not disseminate this message without the permission of the sender. If you have received this communication in error, please notify the sender by reply e-mail, and delete the original message, and all copies, from your system, without reading it. Any dissemination, distribution or copying of this communication is strictly prohibited, and may be a violation of applicable laws.

2 1

Geolocation detection improvement
by Mamitzsch,André 15 Sep '17

15 Sep '17

Hello We are constantly running into issues with the geolocation service and the automated detection of the coordinates – people tend to set additional information in the sysLocation which finally cause the geo api’s to fail. I would like to suggest a small format / code change here to make the geo location detection more usable and reliable. SysLocation should be set up in the form: <Business Name / Rack Location> Street No., ZIP Code City, Country The <Business Name / Rack Location> is still stored in observium but ignored when querying the api. --- geolocation.inc.php.org 2017-07-18 22:09:56.994896291 +0200 +++ geolocation.inc.php 2017-07-18 22:09:40.082938507 +0200 @@ -20,9 +20,14 @@ function get_geolocation($address, $geo_db = array(), $dns_only = FALSE) { global $config; + /* $address parsing, allow business names or additional information */ + /* address line should be: <ACME INC> Test Street 42, 823456 Somewhere */ + $address_orig = $address; + $address = preg_replace("/^<?.*>/","",$address); + $ok = FALSE; - $location = array('location' => $address); // Init location array + $location = array('location' => $address_orig); // Init location array $location['location_geoapi'] = strtolower(trim($config['geocoding']['api'])); if (!isset($config['geo_api'][$location['location_geoapi']])) { -- Mit freundlichen Grüßen, Best regards, André Mamitzsch

4 3

Devices
by Philippe Hurtubise 14 Sep '17

14 Sep '17

Hi, I have 6 VMWare ESXi hosts monitored and when I go in the Devices section under Virtual machines, a lot of them are showing multiple times in the list. Thanks Philippe Hurtubise Administrateur réseau / Network administrator [Autolog logo Signature] T: 450.434.8389 ext. 354 F: 450.434.8395 1240 Michèle-Bohec, Blainville, QC, Canada J7C 5S4 www.autolog.com<http://www.autolog.com/>

3 3

Edit existing alert
by Todd Hank 14 Sep '17

14 Sep '17

I am certainly a newbie yet and I am playing around with alerts. I created a couple alerts that I would like to edit. I do not see a way to edit them. Any Advice? Thanks, Todd Hank Senior Network Administrator (920) 749-0444 Ext. 128 Todd.Hank(a)i-car.com STAY CONNECTED: [http://nebula.i-car.com/i-car/01_Facebook.gif]<https://www.facebook.com/icareducation> [http://nebula.i-car.com/i-car/02_Twitter.gif] <https://www.twitter.com/i_car_education> [http://nebula.i-car.com/i-car/03_Instagram.gif] <https://www.instagram.com/icar_education> [http://nebula.i-car.com/i-car/04_LinkedIn.gif] <https://www.linkedin.com/company-beta/40619> [http://nebula.i-car.com/i-car/05_YouTube.gif] I-CAR.com<http://www.i-car.com> | RTS<http://rts.i-car.com/> | Collision Reporter Magazine<https://www.i-car.com/collisionreporter> [http://nebula.i-car.com/i-car/i-car_logo.gif]<https://www.i-car.com> ________________________________ This message, including any attachments, is intended only for the use of the individual or entity to which it is addressed, and may contain confidential information. Please do not disseminate this message without the permission of the sender. If you have received this communication in error, please notify the sender by reply e-mail, and delete the original message, and all copies, from your system, without reading it. Any dissemination, distribution or copying of this communication is strictly prohibited, and may be a violation of applicable laws.

2 5

New error after update to latest SVN (stable branch)
by Shon Elliott 13 Sep '17

13 Sep '17

Hi Observium List, We updated Observium to the latest svn stable branch today. I made sure we had ran the update, so it shows that everything is up to date, including the database. We found that we ran into a snag when adding new users to the system via the web interface. I was able to add the user via the adduser.php script, but it's missing some data. When I went to go edit it, it logged the same error. Here are the excerpts of the errors below, one for adding the user, and one for editing the user added via adduser.php. [Tue Sep 12 14:23:32.609888 2017] [:error] [pid 42518] [client 1.2.3.4:51614] PHP Fatal error: Call to undefined function hash_equals() in /usr/local/www/observium/html/includes/functions.inc.php on line 313, referer: http://xxx/adduser/ [Tue Sep 12 14:26:36.631482 2017] [:error] [pid 42518] [client 1.2.3.4:10867] PHP Fatal error: Call to undefined function hash_equals() in /usr/local/www/observium/html/pages/edituser.inc.php on line 125, referer: http://xxx/edituser/user_id=13/ Any ideas? Kind Regards, Shon Elliott, KK6TOO Level 3 IP/Routing/Security Network Engineer [unwired-new-logo] (559) 476-9463 - Cell (559) 261-4444 x 129 - Office (559) 943-1025 - Direct selliott(a)getunwired.com<mailto:selliott@getunwired.com> www.getunwired.com<http://www.getunwired.com/>

3 5

One more for the customOID topic
by Jesper Frank Nemholt 13 Sep '17

13 Sep '17

So I also upgraded to the latest and got the autodiscovery on custom OIDs. Didn't have the best effect on my system as it mapped hundreds of individual Isilon nodes to a long range of custom OIDs I had created. So lessons learned / feature requests : - Previously one could pick (one by one or multi select) the devices to be covered in a specific custom OID. THis option seems to have gone now. I'd like that option back, or alternatively be able to somehow filter or group devices. I also use the combined line or stack graphs for certain things and sometime need to show just a group of devices and not all. Right now with the new version I can only show either a single device or all devices as I cannot create custom OID groups and then narrow down what devices to show there. - On systems like Isilon where you may want to both have cluster wide data (so polling the cluster alias) but also monitor each node in the cluster, the lack of the above mentioned filtering/grouping is a problem as currently the custom OID will only work for me if I delete all individual nodes and only monitor the cluster alias. On the other hand, now Servertech Sentry4 devices are better supported, so the net outcome of the upgrade was still positive for me. /Jesper

2 2

Feature idea: custom graphs
by Jesse Defer 12 Sep '17

12 Sep '17

Prior to the recent changes to Custom OIDs (r8738~r8741) we had been abusing the feature to create custom graphs containing multiple hosts. For example we had a graph of emails delivered that combined all of our email servers in one. Now with OID discovery added and manual association removed that graph goes from 20 hosts to 600 and is no longer very useful. I think moving some of the previous functionality of Custom OIDs into it's own Custom Graph feature would be very useful and welcome feedback on the idea. Thanks, Jesse DeFer Arizona State University

5 15

Ports down, but not shown?
by Robert Williams 11 Sep '17

11 Sep '17

Hi all, I've got 12 ports showing as 'Down', both on the main page here... ...and on the menu: However, when you click the link, you don't get any results: (the link goes to: https://observius.cdc.local/ports/state=down/ignore=0/ ) So... How can I find out what/where/how these 12 ports are, so I can 'resolve' them please? Cheers! Robert Williams Custodian Data Centres https://www.CustodianDC.com

4 9

Delete device from custom mod list
by Simon Mousey Smith 11 Sep '17

11 Sep '17

Hi All Is the is a way to delete a device from a Custom OIDs? I use a custom oid to display hotspot users logged in via mikrotiks at 2 sites, however I’ve just seen the OID page has had an update and is showing ALL(12) of our mikrotik devices? I only want to show 2 of our devices!? Regards Simon

1 0

tp-link uptime
by Simon Mousey Smith 11 Sep '17

11 Sep '17

Hi All Im not sure if its Observium or TP-Link I should be asking really but ill ask in both places? Observium told me, one of our switches rebooted (which seemed odd as nobody can gain physical access to it) I checked observium and that shows an uptime of 16h 20m 30s When I snmpwalk the switch I can see DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (5883922) 16:20:39.22 But the TP-Link web panel shows RunTime: 332 day - 2 hour - 2 min - 39 sec ??? Any suggestions would be helpful :) Regards Simon

2 2

Traffic comparison - "No auth" error message
by Youssef BENGELLOUN - ZAHR 10 Sep '17

10 Sep '17

2 4

R8834 breaks rrdtool
by Ron Marosko 10 Sep '17

10 Sep '17

Howdy Guys, Looks like something broke between r8833 and r8834: root@observium:/opt/observium# ./poller.php -h 1198 ___ _ _ / _ \ | |__ ___ ___ _ __ __ __(_) _ _ _ __ ___ | | | || '_ \ / __| / _ \| '__|\ \ / /| || | | || '_ ` _ \ | |_| || |_) |\__ \| __/| | \ V / | || |_| || | | | | | \___/ |_.__/ |___/ \___||_| \_/ |_| \__,_||_| |_| |_| Observium Professional 17.9.8834 http://www.observium.org ##### Starting polling run at 2017-09-09 18:08:42 ##### ##### cityhall-3750e.domain[1198] ##### o OS ios o OS Group cisco o Last poll duration 6.91 seconds o Last Polled 2017-09-09 18:08:04 o SNMP Version v2c o Device status Device is reachable by PING (0.89ms) and SNMP (12.38ms) PHP Fatal error: Uncaught Error: Call to undefined function str_replace_first() in /opt/observium/includes/rrdtool.inc.php:485 Stack trace: #0 /opt/observium/includes/rrdtool.inc.php(620): rrdtool_generate_filename('status.rrd', Array) #1 /opt/observium/includes/polling/functions.inc.php(561): rrdtool_update_ng(Array, 'status', Array) #2 /opt/observium/poller.php(172): poll_device(Array, Array) #3 {main} thrown in /opt/observium/includes/rrdtool.inc.php on line 485 Dropping back to r8833, the poll process runs fine. .Ron -- Ron Marosko, Jr. . . . . . . . . . . . . . . . . . . . . . . . . . . CCIE No. 4526 (R/S), NN5DX Senior Network Engineer RJR Services, Inc. 1108 West Dickinson Blvd, Suite A Fort Stockton, TX 79735 USA o: +1 432 336 5600 x115 c: +1 432 290 6344 e: <mailto:ron@rjr-services.com> ron(a)rjr-services.com pgp pubkey: <http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x778B3B0258AB8B5C> 0x58AB8B5C "To know me is to fly with me." -- This message has been scanned by E.F.A. Project and is believed to be clean.

2 2

FW: Problem with graphs (-nan)
by Peter Derissen 09 Sep '17

09 Sep '17

Hello, Currently Eurofiber is testing Observium in our live network. So far it runs smooth. We only have 1 problem. The graphs are empty (-nan). My guess its a config.php error but im not sure. I have added a screenshot and the config.php file. Regards, Met vriendelijke groet, Peter Derissen Eurofiber Nederland ******** IMPORTANT NOTICE ******** This e-mail (including any attachments) may contain information that is confidential or otherwise protected from disclosure and it is intended only for the addressees. If you are not the intended recipient, please note that any copying, distribution or other use of information contained in this e-mail (and its attachments) is not allowed. If you have received this e-mail in error, kindly notify us immediately by telephone or e-mail and delete the message (including any attachments) from your system. Please note that e-mail messages may contain computer viruses or other defects, may not be accurately replicated on other systems, or may be subject of unauthorized interception or other interference without the knowledge of sender or recipient. Eurofiber only sends and receives e-mails on the basis that Eurofiber is not responsible for any such computer viruses, corruption or other interference or any consequences thereof. Eurofiber Nederland B.V. is registered in the Chamber of Commerce of Amsterdam with number 34134377, VAT number NL 8088.51.524 B01.

5 8

Graph CheckPoint per VSX Concurrent connections
by MAILLET Julien 08 Sep '17

08 Sep '17

Hello, My checkpoint firewall have a running graph for global concurrent connections CHECKPOINT-MIB::fwNumConn.0 = 169 CHECKPOINT-MIB::fwPeakNumConn.0 = 1409 Any chance to add possibility to graph per vsx concurrent connections ? CHECKPOINT-MIB::vsxCountersVSId.1.0 = Counter32: 0 CHECKPOINT-MIB::vsxCountersVSId.2.0 = Counter32: 1 CHECKPOINT-MIB::vsxCountersVSId.3.0 = Counter32: 2 CHECKPOINT-MIB::vsxCountersVSId.4.0 = Counter32: 4 CHECKPOINT-MIB::vsxCountersVSId.5.0 = Counter32: 5 CHECKPOINT-MIB::vsxCountersConnNum.1.0 = Counter32: 20 CHECKPOINT-MIB::vsxCountersConnNum.2.0 = Counter32: 6424 CHECKPOINT-MIB::vsxCountersConnNum.3.0 = Counter32: 0 CHECKPOINT-MIB::vsxCountersConnNum.4.0 = Counter32: 0 CHECKPOINT-MIB::vsxCountersConnNum.5.0 = Counter32: 1499 CHECKPOINT-MIB::vsxCountersConnPeakNum.1.0 = Counter32: 4526 CHECKPOINT-MIB::vsxCountersConnPeakNum.2.0 = Counter32: 3264 CHECKPOINT-MIB::vsxCountersConnPeakNum.3.0 = Counter32: 0 CHECKPOINT-MIB::vsxCountersConnPeakNum.4.0 = Counter32: 0 CHECKPOINT-MIB::vsxCountersConnPeakNum.5.0 = Counter32: 4401 Julien

1 0

Graphs Not Showing (-nan)
by Peter Derissen 08 Sep '17

08 Sep '17

Hello, After filtering and changing some stuff with caching and cron jobs ive got observium running smooth. Only my graphs arnt showing? Any idea? Met vriendelijke groet, Peter Derissen Eurofiber Nederland Network Engineer Safariweg 25-31 +31 (0)6 11587110 3605 MA Maarssen [EF-logo_rood_RGB -handtekening]<http://www.eurofiber.nl/> Volg ons op Twitter<https://twitter.com/Eurofiber> | Linkedin<https://www.linkedin.com/company/eurofiber> | Youtube<https://www.youtube.com/user/Eurofibergroup> [cid:image002.png@01D225FF.7ECDA420]<http://bit.ly/2eaBgRh> ******** IMPORTANT NOTICE ******** This e-mail (including any attachments) may contain information that is confidential or otherwise protected from disclosure and it is intended only for the addressees. If you are not the intended recipient, please note that any copying, distribution or other use of information contained in this e-mail (and its attachments) is not allowed. If you have received this e-mail in error, kindly notify us immediately by telephone or e-mail and delete the message (including any attachments) from your system. Please note that e-mail messages may contain computer viruses or other defects, may not be accurately replicated on other systems, or may be subject of unauthorized interception or other interference without the knowledge of sender or recipient. Eurofiber only sends and receives e-mails on the basis that Eurofiber is not responsible for any such computer viruses, corruption or other interference or any consequences thereof. Eurofiber Nederland B.V. is registered in the Chamber of Commerce of Amsterdam with number 34134377, VAT number NL 8088.51.524 B01.

1 0

Win2012R2
by Jacek.Dabrowski＠selgros.pl 08 Sep '17

08 Sep '17

Hello, Can anyone know why observium bad recognizes the operating system ? [cid:image001.png@01D3271E.D2458570][cid:image002.png@01D3271E.D2458570] Jacek Dąbrowski Koordynator Administratorów IT [cid:image005.jpg@01D3271E.E559DC10] Transgourmet Polska Sp. z o.o. Zamenhofa 133, 61-131 Poznań, Polska tel.: +48 61 874 20 17 kom.:+48 604 069 933 E-mail: Jacek.Dabrowski(a)selgros.pl www.selgros.pl<http://www.selgros.pl> www.selgros24.pl<http://www.selgros24.pl> www.transgourmet.pl<http://www.transgourmet.pl> Transgourmet Polska Sp. z o.o. jest zarejestrowana w Sądzie Rejonowym Poznań-Nowe Miasto i Wilda w Poznaniu, Wydział VIII Gospodarczy Krajowego Rejestru Sądowego pod nr KRS: 0000045597. NIP: PL 781-10-11-998, REGON 630375413. Wysokość kapitału zakładowego: 310.000.000,00 złotych. Zapraszamy do korzystania z aplikacji HELPDESK<https://horologium>

4 6

Adding new graph
by MAILLET Julien 06 Sep '17

06 Sep '17

Hello, I'm following this to add a custom graph but it seems outaded http://docs.observium.org/developing/add_graph/ I try and use the *new* format of graphing poller (Examples are in NS-ROOT-MIB). So I created a file in $basedir/includes/polling/graphs/ but graph still don't work. Any new procedure available ? Julien

2 6

STOP SUBSCRIPTION
by Idriss SOIDIKI 06 Sep '17

06 Sep '17

Hello, I want stop receive the mailing list, please Thank you --

2 1

Device description in email template
by Richard Wigzell 06 Sep '17

06 Sep '17

Hello, what is the placeholder or keyname to use to get the device description / purpose added to the email alert template? [cid:image001.jpg@01CE9215.D39244B0]<https://www.it.ox.ac.uk/> Richard Wigzell Networks, Security and Server Specialist IT Services | University of Oxford 13 Banbury Road, Oxford OX2 6NN T: 01865 616282 www.it.ox.ac.uk<https://www.it.ox.ac.uk/>

1 0

CyberPower PDU compatibility
by Kaya Saman 05 Sep '17

05 Sep '17

Hi, I've been recommended a PDU by CyberPower model: PDU15SWHVIEC8FNET and was wondering about the support if-at-all in Observium. Already I have had a bad experience with Eaton and switching to APC was much better. Would anyone be able to provide any information as to whether this make of PDU will work well with Observium and Net-snmp? Many thanks. Kaya

2 2

Traffic Summary on the front page
by Gumilar Siegfried 05 Sep '17

05 Sep '17

Hello, I just noticed the addition of a new element to the Traffic Summary on the front page: [cid:image001.png@01D32563.BD4879F0] I like the fact that we now also have a history of the Peering to Transit Ratio directly on the front page. But I am missing an information about the timeframe that is displayed here. Could you make it look like this? [cid:image003.png@01D32564.D6332630] That would be awesome! Regards, Siegfried

4 11

Re: [Observium] Traffic Summary on the front page
by Youssef BENGELLOUN - ZAHR 04 Sep '17

04 Sep '17

1 0

mib folder
by Tomasz.Kwiecien＠nordea.com 31 Aug '17

31 Aug '17

Hi, I know that you can't simply add mibs to observium :) I just want to add mib, so I can use object names instead of OID in code. I've added in include/definitions/os.inc.php: $os = "alteon-ad"; $config['os'][$os]['mibs'][] = "ALTEON-CHEETAH-NETWORK-MIB"; And try add ha status for this device using $alteon['hastatus'] = snmpwalk_cache_oid($device, 'vrrpInfoHAState', array(), 'ALTEON-CHEETAH-NETWORK-MIB'); In debug mode I can see errors /usr/bin/snmpbulkwalk -t '5' -r '3' -v2c -c 'something' -Pu -OQUs -m ALTEON-CHEETAH-NETWORK-MIB -M /opt/observium/mibs 'udp':'myDevice':'161' vrrpInfoHAState Cannot find module (ALTEON-CHEETAH-NETWORK-MIB) But file exist in 2 locations: /opt/observium/mibs/nortel/ALTEON-CHEETAH-SWITCH-MIB /opt/observium/mibs/alteon/ALTEON-CHEETAH-SWITCH-MIB How can I map this mib to alteon-ad os, so snmp commands would have options: -m ALTEON-CHEETAH-NETWORK-MIB -M /opt/observium/mibs/alteon:/opt/observium/mibs/rfc Instead of: -m ALTEON-CHEETAH-NETWORK-MIB -M /opt/observium/mibs ? Best regards, Tomasz Kwiecień Nordea | Network Security Operations Visit me: Łuzycka 8C, Gdynia Tel: +48 586671348 E-mail: tomasz.kwiecien(a)nordea.com<mailto:tomasz.kwiecien@nordea.com> Web: nordea.com<http://http/www.nordea.com> Nordea Bank AB (publ). Company registration number/VAT number 516406-0120/SE663000019501. The board is domiciled in Stockholm, Sweden This e-mail may contain confidential information. If you receive this e-mail by mistake, please inform the sender, delete the e-mail and do not share or copy it.

2 2