- observium - lists.observium.org

Port errors
by Darian Jimenez 05 Sep '14

05 Sep '14

I just saw I had a warning on port errors and looked at it. It is monitoring a Juniper switch interface. From the legend I can't tell what the "m" stand for for the y axis. would this be resource errors from the switch interface stats? Errors: 275, Drops: 0, Framing errors: 275, Runts: 0, Policed discards: 0, L3 incompletes: 0, L2 channel errors: 0, L2 mismatch timeouts: 0, FIFO errors: 0, Resource errors: 11740453 Thanks, Darian

3 3

Empty graphs
by Joel 05 Sep '14

05 Sep '14

Hi all, just installed Observium CE 0.14.4.5229 on a CentOS 6.5 64bits in VMware Workstation 9 environment : no problem thanks to well done install procedure (http://www.observium.org/wiki/RHEL_Installation); added manually network devices via following commands with no errors : ./add_device.php xxx.xxx.xxx.xxx ./discovery.php -h all ./poller.php -h all crontab updated as stated in install procedure ; Everything seems OK during all these steps ; When looking at the results via web interface, I can see all (CISCO here) devices with all their discovered characteristics (type/model, soft version, interfaces, % RAM, % CPU, thruput figures on interfaces, ...) but no graph is drawn at all (even after 4 hours) ; by the way, the graphs legends are correclty, and the grids too, but no curve drawn; when looking at /opt/observium/rrd directory, I can see a sub-dir created per each disvovered device and inside each of them, 1 RRD file created for each collected variable ; (each device RRD subdir is about 40MB after a while, RRD files inside are not empty) Any idea to investigate more about those empty graphs ? thanks for any help

4 5

wrong post
by Joel Guillerm 05 Sep '14

05 Sep '14

sorry for previous post about netdisco; my mistake

1 0

(no subject)
by Joel Guillerm 05 Sep '14

05 Sep '14

Hello Chris, thanks for your feedback; in the meantime, I had downloaded and tested the netdisco demo VMware appliance and got some problems ; I posted the following mail on the netdisco mailing list but did not get any feedback yet; if you have any ideas, thanks in advance Joel ************************************************* newbie in netdisco, just downloaded and tested netdisco demo VMWare package (V1.0 netdisco version ... a bit too old maybe, even for a test) To run a quick test, 1) I just edited community values and uncomment "discover_only =" statement followed by a comma-separated list of IP routers to be discovered in /usr/local/netdisco/netdisco. conf ; I let "#discover_no =" statement untouched ; 2) then, I restart netdisco via : ./netdisco -p restart ==> OK after a few minutes, I still did not see any IP routers added on the discover_only list shown via web interface; nothing shown in /usr/local/netdisco/data/logs apart from messages related to "netdisco starting" 3) so, I tested the 2 manual commands below via SSH : ./netdisco -d xxx.xxx.xxx.xxx (for 1 single IP) ./netdisco -r xxx.xxx.xxx.xxx,yyy.yyy.yyy. yyy, zzz.zzz.zzz.zzz, .... for my list of IPs routers Both commands work successfully and results are OK via web interface Questions : a) what else should I do to avoid having to issue the manual commands and let netdisco do its job ? b) with recent netdisco versions, is there a function that allows to export resulting infos (such as the Devices List with their discovered ard/soft infos) as a CSV file for example ? thanks for any help *************************************************

1 0

Accounting for electricity
by Simon Schmitz 04 Sep '14

04 Sep '14

Hi, what do you think of an accounting for electricity, the same as the network port on a switch only here of a PDU switch. Simon

3 2

Alerts for Network devices›
by Darian Jimenez 04 Sep '14

04 Sep '14

Hello, I just need basics on alerting if device is down or maybe if VPN interface is down etc. Attached I set an alert to just try and find devices that are currently "up" to see if it discovers them with the names starting as fw*. Once it works I will change to check for devices that are “down” What am I doing wrong here since it isn't finding anything.

3 4

Re: [Observium] Alerts for Network devices›
by Adam Armstrong 04 Sep '14

04 Sep '14

1 0

How to limit Discovery/Polling to infos visible on the main Device panel ?
by Joel Guillerm 03 Sep '14

03 Sep '14

Hello, newbie in Observium ; is it possible to configure Observium to limit its job to get only the informations available on the main Devices panel ? i.e. Device/Location, Platform, Operating System, Uptime/Sysname so, nothing about interfaces, CP, RAM, ... This would be for quick and basic Device inventory purpose only for some environments The idea is to reduce the total discovery/polling time to the minimum for this basic inventory, otherwise, this could last very long time in case of 100's of devices to deal with. thanks for any advice

2 1

Re: [Observium] Google Maps not showing
by Christian Gerbrandt 03 Sep '14

03 Sep '14

I have this in my config: $config['geocoding']['api'] = 'google'; And is working fine. Where can I find information about this config changes? On Sep 01, 2014, at 05:02 PM, Adam Armstrong <adama(a)memetic.org> wrote: On 2014-09-01 16:23, Sebastian Pitei wrote: > Hi everyone, > > First, congrats ot the devs for making such a nice piece of software. > Simple, to the point, perfect! > > Second, my issue: I'm trying to change the maps engine to Google Maps. > I've change the engine to "google" in config.php but unfortunately > nothing is happening. Any ideas? google-mc is the default, and the only one currently expected to work. The old API map was kinda messy, and no one really uses it anymore. adam. _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

3 2

Observium Draw errors
by Adriaan Smuts 03 Sep '14

03 Sep '14

Hi Guys, For some reason Observium is giving Draw Errors on all of our graphs. This started happening after the latest svn update. We have this error on our live observium and our staging/testing one. Does anyone know how to fix this? Please see screenshot below: [cid:image001.png@01CFC769.4007A4D0] Regards Adriaan Smuts Systems Administrator - Windows [file:///C:\Users\adriaan\AppData\Roaming\Microsoft\Signatures\WebAfrica_Files\signature_logo.jpg] ________________________________ Direct Line +27 21 464 9565 Reception 086 000 9500 Website www.webafrica.co.za<http://www.webafrica.co.za/>

2 2