- observium - lists.observium.org

DB grow to fast
by Thomas Grunert 28 Mar '14

28 Mar '14

Hi all, my database is grow very fast. Is there a cyclic clean up which deletes unnessesary entries from the db to prevent garbage? How long are entries kept in the db? Can anybody tell me the syntax to reduce the rate-time for trap and log entrys in the database? many thanks Thomas

2 1

Re: [Observium] SVI - Vlan IF graphs
by Marco Spicuglia 28 Mar '14

28 Mar '14

Hi Adam, mmh, thanks. -------------- snmpwalk -v 2c -c COMMUNITY HOST 1.3.6.1.4.1.9.9.648 iso.3.6.1.4.1.9.9.648 = No Such Object available on this agent at this OID -------------- where 1.3.6.1.4.1.9.9.648 id is suppose to poll CISCO-VIRTUAL-INTERFACE-MIB, which is included in the Observium database and supposedly supported by the Nexus 6001. Is this a Cisco bug or should I activate something somehow somewhere? Cheers, Marco Met vriendelijke groet/ Kind regards, Marco Spicuglia Network engineer - Programmer ReasonNet B.V. Gyroscoopweg 134 - 140 1042AZ Amsterdam W. www.reasonnet.com E. Marco.Spicuglia(a)reasonnet.com T. F. ReasonNet zoekt datacenter support engineers. Ga voor deze en andere interessante vacatures binnen ReasonNet naar http://www.reasonnet.com/nieuws ReasonNet, shall not be liable for damages resulting from the use of electronic means of communication, including -but not limited to- damages resulting from failure or delay in delivery of electronic communications, interception or manipulation of electronic communications by third parties or by computer programs used for electronic communications and transmission of viruses and other malicious code.________________________________________ From: Adam Armstrong [adama(a)memetic.org] Sent: 26 March 2014 02:29 To: Marco Spicuglia Subject: Re: [Observium] SVI - Vlan IF graphs Are you actually snmpgetting the counters to check? I suspect, as usual, a Cisco SNMP bug. There really is no scope for us to fail to put interface data into the rrd. Adam. On 25 Mar 2014 18:57, Marco Spicuglia <Marco.Spicuglia(a)reasonnet.com> wrote: > > Hello there, > > I would like to monitor SVI bandwidth on those devices that support such counters. > I activated the etherlike mib option in the config and started polling a Nexus 6k, which supports snmp counters on vlan interfaces. > I see the snmp counters increasing on the switch, but I see only blank graphs on vlan interfaces, which are properly detected, including their status. > > The device is properly polled for anything else and it seems that all needed mibs are already included in your distribution. > I am running the latest stable release. > > Any idea? Am I missing anything? > > Thanks for your help. > > Regards, > > Marco > > Met vriendelijke groet/ Kind regards, > > Marco Spicuglia > > Network engineer - Programmer > > ReasonNet B.V. > Gyroscoopweg 134 - 140 > 1042AZ Amsterdam > W. www.reasonnet.com > E. Marco.Spicuglia(a)reasonnet.com > T. > F. > > ReasonNet zoekt datacenter support engineers. Ga voor deze en andere interessante vacatures binnen ReasonNet naar http://www.reasonnet.com/nieuws > > ReasonNet, shall not be liable for damages resulting from the use of electronic means of communication, including -but not limited to- damages resulting from failure or delay in delivery of electronic communications, interception or manipulation of electronic communications by third parties or by computer programs used for electronic communications and transmission of viruses and other malicious code. > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

3 6

Google Maps
by Kleber C. S. Coelho 28 Mar '14

28 Mar '14

Prezados, boa noite! Gostaria de saber se ja é possível ativar o mapa do Google, igual ao da demostração, na página do observium, utilizando a versão comunitária. Gostaria também de deixar uma mensagem de protesto contra a política de versões comunitárias e pagas. Eu até entendo os motivos, mas não concordo de forma alguma. Se alguém puder responder minha dúvida sobre o google maps agradeço! Obrigado. Dear, good night! I wonder if you can already activate the Google map, same as the demo, in observium page, using the community version. I would also like to leave a message of protest against the policy community and paid versions. I can understand the reasons, but I do not agree at all. If anyone can answer my questions about the google maps thanks! Thank you.

9 11

Error Global Settings Page
by Gökmen Çakmak 28 Mar '14

28 Mar '14

Hi everyone, Why is this happening? Best Regards, Gökmen

6 14

Issues with bind graphs - Where to start looking?
by Ricardo M Meleschi 28 Mar '14

28 Mar '14

root@austx-sys-tools-01:~# uname -m i686 (hangs head in shame) Yes.. Yes I did... Well, now I know how to fix it.. =) Thanks Adam! Ricardo From: Adam Armstrong <adama(a)memetic.org> Did you, perchance, foolishly install a 32-bit version of Ubuntu? :D root@alpha:~# php -r 'echo PHP_INT_MAX;' 9223372036854775807 adam. On 2014-03-27 14:01, Ricardo M Meleschi wrote: > (just an update on my troubleshooting here) > > It looks like the version of PHP that comes installed with the version > of Ubuntu that Observium recommends is limited to 32-bit signed > integers: > > root@xxx:/opt/observium/includes/polling/applications# php -r 'echo > PHP_INT_MAX;' > 2147483647 > > That explains the issue that I have been having with bind counters > above this value being saved at a value of 2147483647.

1 0

Issues with bind graphs - Where to start looking?
by Ricardo M Meleschi 28 Mar '14

28 Mar '14

Hello everyone, I've identified an issue with storing of values that are grabbed by the unix-agent. Specifically, a problem with the bind sub-agent. Apparently, when req-in,QUERY exceeds a value of 2,147,483,648, the value that actually gets stored in the app-bind-122-req-in.rrd is: # rrdtool info app-bind-122-req-in.rrd | grep query ds[query].index = 0 ds[query].type = "DERIVE" ds[query].minimal_heartbeat = 600 ds[query].min = 0.0000000000e+00 ds[query].max = 7.5000000000e+06 >> ds[query].last_ds = "2147483647" << ds[query].value = 0.0000000000e+00 ds[query].unknown_sec = 0 This is despite the current value actually being: # ./bind | grep -i req-in,Q req-in,QUERY:2368417221 I initially thought there was an issue with a 32 bit vs 64 bit counter in the RRD itself, but it looks like ds[query].max is well above a 32bit variable's max value. I am at a loss as to where the problem may be and am hoping that someone on the mailing list can point me in the right direction. I can't believe I'm the first one to run into this issue actually... Here's what happens to my graph when this issue arises: This happens to other dns graphs as well, but it happens to this one the quickest, since it hits that 'limit' faster than the other counters do. Additionally, I'm running 0.14.3.5117 if that helps. If I restart named, the graph begins graphing properly again, but I don't want to consider that a 'fix', especially since I'd be resetting all of my bind servers every week. Doable, but not ideal. Thanks for any assistance, Ricardo

2 4

Monthly Thumbnails not Updating
by Cameron Jones 28 Mar '14

28 Mar '14

It appears that my monthly graph thumbnails are not updating, but when I go into view the RRD from a monthly perspective the data is there. Check out the attached screen-shots to better explain the issue. I'm currently running the non subscription version. https://www.dropbox.com/s/mifk9lm9yp40ebh/Screen%20Shot%202014-03-27%20at%2 010.22.47%20AM.png https://www.dropbox.com/s/02teszwfy8rhfml/Screen%20Shot%202014-03-27%20at%2 010.23.38%20AM.png Thanks in advance!

2 1

CPU's on mikrotik
by David Peall 28 Mar '14

28 Mar '14

Servers appear quite nicely with a compound graph but my Mikrotik routers have one per CPU is this just something that could be done easily? Also I think the SNMP for the CPU name is below I’ve got 2 examples: SNMPv2-SMI::mib-2.47.1.1.1.1.7.65536 = STRING: “tilegx” SNMPv2-SMI::mib-2.47.1.1.1.1.7.65536 = STRING: "MIPS 24Kc V7.4" vs Thanks — David Peall Domain Name Services

4 4

Re: [Observium] Cisco Small Business series
by support nuckleo 28 Mar '14

28 Mar '14

Hi Mike, I have seen your email now, thank you for your suggestion. Good manners are always appreciated. Kind regards. F. _____________________________________________________________________ NUCKLEO Information Technology Solutions Support & Delivery Team http://www.nuckleo.com (website) Twitter:@Nuckleo _____________________________________________________________________ Di Mercoledì, 08-01-2014 alle 21:42 Mike Stupalov ha scritto: Hi, I think Francesco uses CE edition. In latest Subscription Edition support for Cisco SB already added. Upgrade your observium instance or wait next CE edition. :) [1]http://www.observium.org/wiki/Edition_Split Mike. On Sat, Jan 4, 2014 at 12:07 AM, Nikolay Shopik wrote: Workaround to what? Cisco SB support was added by Mike, we tested it as I was asked to add such support, no issues here. On 03.01.2014 19:51, support nuckleo wrote: > Hello everybody I would like to share a small workaround in order > to monitoring the cisco Small business series sg 200/300 in the right > way > > I have add some mibs in the /opt/observium/includes/defaults.inc.php > $config['mibs']['CISCOSB-MIB'] = > 1;$config['mibs']['CISCOSB-CPU-COUNTERS-MIB'] > = 1; > $config['mibs']['CISCOSB-JUMBOFRAMES-MIB'] > = 1; > $config['mibs']['CISCOSB-vlan-MIB'] = 1; > $config['mibs']['CISCOSB-vlanVoice-MIB'] > = 1; > $config['mibs']['CISCOSB-SMON-MIB'] = 1; > > Detect your sysdescr sysDescr in this way: > > snmpwalk -c public -v2c device sysDescr > > and after I made some changes mapping the sysDescr on the right os > so in > /opt/observium/includes/discovery/os/cisco.inc.php add > > else if (strstr($sysDescr, "50-Port Gigabit Smart Switch")) { $os = > "ciscosb"; } > else if (strstr($sysDescr, "SG200-50P 50-Port Gigabit PoE Smart > Switch")) { $os = "ciscosb"; } > > Then if you have just discoverd, delete your cisco small business > devices and rediscovery the devices again. > Thats all! > > Francesco Pansini > _____________________________________________________________________ > NUCKLEO Information Technology Solutions > Support & Delivery Team > http://www.nuckleo.com (website) > Twitter:@Nuckleo > _____________________________________________________________________ > > > > > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium-- Mike Stupalov [2]http://observium.org/ Links: ------ [1] goog_2143683876 [2] http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

delete ports?
by John Poznicek 27 Mar '14

27 Mar '14

I have looked and looked and can not find how to delete ports. There are many ports that are added when pointing to my windows machine for example, old interfaces, etc. tunnels that are not listed ipconfig /all, etc. How do you delete them? Do you have to edit the $config['bad_if'] to include the names of the interfaces you dont want? TIA

3 4