- observium - lists.observium.org

Oracle E-SBC support
by Johnathon Voegeli 31 May '18

31 May '18

Hey guys, Does anyone here monitor an Oracle (AcmePacket) Session Border controller? I see it’s slightly supported, but does not support the ap-SIP function with SNMP. I am trying to get a custom OID to monitor a sip endpoint at least basic monitoring, but was curious if any one had any luck with anything more? I can manually add each OID for SIP Agent status, but it’s a manual process each time we add a customer/endpoint to each cluster and of course only provides a 1, 2, 3. I have it setup to alert on anything other than 3. Thanks in Advance! ~JV

1 0

ASR1k subinterface
by Mirditor Kuçaj 29 May '18

29 May '18

Hello Does anybody has the issue about incorrect traffic pooling on subinterfaces over portchannel. The device is Cisco ASR1001-X. Earlier with subinterfaces on TE interface it was ok. [root@obs-55 observium]# php poller.php -h 262 --//-- +---------+--------------------+------------------+--------+----------+----- -----+---------+----------+--------+---------+----+ | ifIndex | Label | Type | Speed | BPS In | BPS Out | Data In | Data Out | PPS In | PPS Out | HC | +---------+--------------------+------------------+--------+----------+----- -----+---------+----------+--------+---------+----+ | 15 | Po1 | Virtual/Internal | 20Gbps | 10.7Gbps | 10.5Gbps | 284GB | 279GB | 1.6M | 1.58M | Y | | 16 | Po1.6 | L2 VLAN (802.1Q) | 20Gbps | 3.28kbps | 378bps | 91.3kB | 10.5kB | 2.98 | 43.8m | Y | | 17 | Po1.21 | L2 VLAN (802.1Q) | 20Gbps | 592kbps | 406bps | 16.1MB | 11.3kB | 650 | 0.8 | Y | | 18 | Po1.23 | L2 VLAN (802.1Q) | 20Gbps | 20.8Mbps | 2.19kbps | 565MB | 60.8kB | 15.1k | 4.26 | Y | | 19 | Po1.24 | L2 VLAN (802.1Q) | 20Gbps | 4.77Mbps | 5.23kbps | 129MB | 145kB | 4.26k | 10.1 | Y | | 20 | Po1.25 | L2 VLAN (802.1Q) | 20Gbps | 3.19Mbps | 2.66kbps | 86.7MB | 74kB | 2.45k | 5.2 | Y | | 21 | Po1.27 | L2 VLAN (802.1Q) | 20Gbps | 28Mbps | 4.24kbps | 761MB | 117kB | 8.72k | 8.14 | Y | Thx

2 1

file that controls alarm output
by Mark Carter 29 May '18

29 May '18

Hi, what file controls alarm output? I have alarms going into a "Slack" channel and want to format them so they take up less lines. Currently an Alarm takes up 7 lines. Thank you Arthur

2 1

Cisco 3750 Temperature
by Storer, Darren 29 May '18

29 May '18

Here's an odd one... Temperature is reported correctly by many models of Cisco catalyst devices but on one of the Observium nodes there are two 3750 switches with different behaviour. The 3750 with IOS 15 is okay and reports temperature but an older 3750 under IOS 12 doesn't return temperature, even though I feel sure that it did a few years ago. Observium version: 18.5.9244 (24th May 2018) Has anyone else observed this behaviour? Update: Just checked an old 2960, still on IOS 12 and found that it doesn't display temperature but a 2960 with IOS 15 is okay. Any advice gratefully received. Thanks Darren

1 0

(no subject)
by Ricardo Franco Cantero 29 May '18

29 May '18

Hi, What would be the best way to create an alert on reboot? For example after a power outage? Would that be an alert checker with up_time less than 20 minutes? Or a syslog alert with /rebooted/ ? Kind regards, Ricardo Franco Cantero

3 2

Observium CE 17.9.8859 LDAP authentication issue
by Jean-Francois Allain 29 May '18

29 May '18

Hello everybody, I did an upgrade of Observium recently from version 14.4.5229 to version 17.9.8859 and I have authentication issue with LDAP now. I was wondering if Observium CE 17.9.8859 was compatible with the following version of PHP LDAP module : php7.0-ldap Thanks in advance, -- *Jean-François Allain*

3 7

Exclude device from geolocation
by Christian Eriksson 28 May '18

28 May '18

Hi, Is it possible to exclude a device from being targeted by the geolocation settings? In my case, I am polling a Cisco ASA security context and both physical devices in the HA cluster are on two different locations /Christian

2 1

BGP polling inside VRF
by Jan Horacek 25 May '18

25 May '18

Hi guys, I`m not sure if this question was already answered or not, but I was asked to do research how Observium could monitor BGP peers inside the VRFs to alert us if any peer flaps or is down. I can set up alert notification based on the syslog, but this module is sending emails only and doesn`t show notification on the main dashboard. Do you have any idea if would be possible support snmp-context for every BGP peers in observium? Using SNMPv3 on all routers or how to display alerts on the dashboard based on syslog policy? Thanks Jan

3 4

[Question] Problem Alert Mails
by San Rollheiser 24 May '18

24 May '18

Hi guys, sorry for bother you, but have a question about the email configuration. After the update a few versions back work fine the alerts by email. But now not work, only work my integration with Slack, but i need the email alerts. My configuration is this: config.php // Set up a default alerter (email to a single address) $config['email']['default'] = "alarmas(a)tinitix.com"; $config['email']['from'] = "Alarmas <alarmas@tinitix>"; $config['email']['default_only'] = TRUE; /include/defaults.inc.php // Mailer backend Settings $config['email']['enable'] = TRUE; // Enable/Disable email globally $config['email']['from'] = TRUE; // Mail from. Default: "Observium" <observium@`hostname`> $config['email']['default'] = TRUE; // Default alert recipient $config['email']['default_only'] = FALSE; // Only use default recipient (all alerts send to default recipient) $config['email']['graphs'] = TRUE; // Allow graphs in mail body $config['email']['backend'] = 'smtp'; // Mail backend. Allowed: "mail" (PHP's built-in), "sendmail", "smtp". // sendmail backend specific options $config['email']['sendmail_path'] = '/usr/sbin/sendmail'; // The location of the sendmail program. // smtp backend specific options $config['email']['smtp_host'] = 'my_ip_smtp_server'; // Outgoing SMTP server name. $config['email']['smtp_port'] = '465'; // The port to connect. $config['email']['smtp_timeout'] = '60'; // SMTP connection timeout in seconds. $config['email']['smtp_secure'] = 'ssl'; // Enable encryption. Use 'tls' or 'ssl' $config['email']['smtp_auth'] = TRUE; // Whether or not to use SMTP authentication. $config['email']['smtp_username'] = 'soporte(a)tinitix.com'; // SMTP username. Thx. BR Santiago

2 1

Pulling VTI interface descriptions from a Centos 7 based router
by Ben Maschke 24 May '18

24 May '18

Hi guys, is there a way to pull interface descriptions from a Centos 7 based router? It's based on vti interfaces and the alias parameter: ip link set vti10 up mtu 1400 alias "test name" Observium only pulls the interface IP - and has ignored the description so far Thank you very much in advance -- *Ben Maschke* Senior System Engineer *Shazam* 26-28 Hammersmith Grove, London, W6 7HA Please consider the environment before printing this document Shazam Entertainment Limited is incorporated in England and Wales under company number 3998831 and its registered office is at 26-28 Hammersmith Grove, London W6 7HA.

2 1