- observium - lists.observium.org

Re: [Observium] question about wmi
by Tony Guadagno 17 Dec '21

17 Dec '21

Rando, I followed this KB https://docs.observium.org/device_windows/ and it just worked. The reason I asked the questions is that it is not immediately obvious that it is working or not. The poller.php -m wmi -v proves it is working but also, I realized that if wmi is working, then your Microsoft devices will show a “windows services” tab. Also, I have Observium installed on RHEL 8. There seems to be no wmi package for version 8 (CentOS or RHEL). I installed the wmi RPM for version 7 and it seems to be working…fyi Good luck Tony From: Rando Sui Sent: Friday, December 17, 2021 6:29 AM To: Observium Cc: Tony Guadagno Subject: RE: [Observium] question about wmi Hello, How did you get WMI working and passing info? Greetings, Rando. From: observium <observium-bounces(a)observium.org> On Behalf Of Tony Guadagno via observium Sent: kolmapäev, 15. detsember 2021 20:33 To: Observium <observium(a)observium.org> Cc: Tony Guadagno <tonyg(a)guadagno.org> Subject: Re: [Observium] question about wmi All, thanks for the help….i think wmi is working because I am now seeing the “windows services” tab on my windows servers. That was not present before. Thanks again Tony From: Adam Armstrong via observium Sent: Tuesday, December 14, 2021 7:08 PM To: 'Observium' Cc: Adam Armstrong Subject: Re: [Observium] question about wmi There’s not likely to be any WMIC messages in that log, not much goes into there. WMIC isn’t used for very much. It slightly improves some windows data, mostly storage. You’ll probably see whatever it does by doing a debugged poller run for the device you’re using WMIC with. Adam. From: observium <observium-bounces(a)observium.org> On Behalf Of Tony Guadagno via observium Sent: 14 December 2021 18:36 To: Pisano, Anthony D. via observium <observium(a)observium.org> Cc: Tony Guadagno <tonyg(a)guadagno.org> Subject: [Observium] question about wmi Hi, I have enabled wmi on my install. I have tested my config with wmic and it seems to work. I have put the global parms in and I am not seeing any log messages about wmi. How do I know if wmi is being attempted? [2021/12/14 18:30:01 +0000] discovery.php(560036): /opt/observium/discovery.php: new - 0 devices discovered in 0.001 secs [2021/12/14 18:30:04 +0000] poller.php(560053): poller.php: abc-wolcott2.company.local - 1 devices polled in 2.943 secs [2021/12/14 18:30:07 +0000] poller.php(560051): poller.php: abc-lyo-sw-3.company.local - 1 devices polled in 5.134 secs [2021/12/14 18:30:07 +0000] poller.php(560049): poller.php: abc-observium.company.local - 1 devices polled in 5.509 secs [2021/12/14 18:30:12 +0000] poller.php(560047): UNIX-AGENT: Connection on tcp://abc-esx15.company.local:36602 failed. ERROR: 110 Connection timed out [2021/12/14 18:30:14 +0000] poller.php(560047): poller.php: abc-esx15.company.local - 1 devices polled in 12.67 secs [2021/12/14 13:30:14 -0500] poller-wrapper.py(560037): /opt/observium/poller-wrapper.py: processed 4 devices in 13.78 seconds with 4 threads, load average (5min) 0.13 Tony

1 0

Re: [Observium] question about wmi
by Tony Guadagno 17 Dec '21

17 Dec '21

All, thanks for the help….i think wmi is working because I am now seeing the “windows services” tab on my windows servers. That was not present before. Thanks again Tony From: Adam Armstrong via observium Sent: Tuesday, December 14, 2021 7:08 PM To: 'Observium' Cc: Adam Armstrong Subject: Re: [Observium] question about wmi There’s not likely to be any WMIC messages in that log, not much goes into there. WMIC isn’t used for very much. It slightly improves some windows data, mostly storage. You’ll probably see whatever it does by doing a debugged poller run for the device you’re using WMIC with. Adam. From: observium <observium-bounces(a)observium.org> On Behalf Of Tony Guadagno via observium Sent: 14 December 2021 18:36 To: Pisano, Anthony D. via observium <observium(a)observium.org> Cc: Tony Guadagno <tonyg(a)guadagno.org> Subject: [Observium] question about wmi Hi, I have enabled wmi on my install. I have tested my config with wmic and it seems to work. I have put the global parms in and I am not seeing any log messages about wmi. How do I know if wmi is being attempted? [2021/12/14 18:30:01 +0000] discovery.php(560036): /opt/observium/discovery.php: new - 0 devices discovered in 0.001 secs [2021/12/14 18:30:04 +0000] poller.php(560053): poller.php: abc-wolcott2.company.local - 1 devices polled in 2.943 secs [2021/12/14 18:30:07 +0000] poller.php(560051): poller.php: abc-lyo-sw-3.company.local - 1 devices polled in 5.134 secs [2021/12/14 18:30:07 +0000] poller.php(560049): poller.php: abc-observium.company.local - 1 devices polled in 5.509 secs [2021/12/14 18:30:12 +0000] poller.php(560047): UNIX-AGENT: Connection on tcp://abc-esx15.company.local:36602 failed. ERROR: 110 Connection timed out [2021/12/14 18:30:14 +0000] poller.php(560047): poller.php: abc-esx15.company.local - 1 devices polled in 12.67 secs [2021/12/14 13:30:14 -0500] poller-wrapper.py(560037): /opt/observium/poller-wrapper.py: processed 4 devices in 13.78 seconds with 4 threads, load average (5min) 0.13 Tony

2 1

Re: [Observium] Cannot buy Subscription for Professional version
by Thodoris Lakiotis 17 Dec '21

17 Dec '21

Hello Everything were sorted out!! Subscription is done. The question is: How can i license current Observium Installation with the new license details? Thanks!! Thodoris On Thu, Dec 16, 2021 at 1:21 PM Thodoris Lakiotis <tlak(a)synapsecom.gr> wrote: > Hello > > I feel here that you are not got what is the point. > > The subscription is canceled. This is done. End of story. > > Now i need to buy again, but just for one year, without yearly > subscription. But paddle do not give that option by default. I can for sure > do it as you suggest, but i just can't proceed, because my PayPal account > do not allow to buy subscription based services, but only one-off. > From PayPal they say that the merchant do not allow to pay with PayPal > balance?!? > > Is this more clear? > > Thodoris > > On Thu, Dec 16, 2021 at 12:55 PM Simon Smith via observium < > observium(a)observium.org> wrote: > >> Hi, >> >> Why not subscribe for the year, >> >> Let paddle take the money, >> >> Let observium give you user/pass etc in there panel, >> >> Then in a days time, go into the observium panel and cancel your >> subscription with paddle? >> >> Then it wont auto-renew next year!? >> >> Regards >> >> Simon >> >> On 16 Dec 2021, at 10:39, Thodoris Lakiotis via observium < >> observium(a)observium.org> wrote: >> >> Hi Adam, thanks for your responce. >> >> The problems here are that i cannot find a representative from Paddle. >> And i cannot buy one year license without subscription. I need one-off >> payments, not recurring with subscriptions. >> >> Is there anyone from paddle that could help me address this issue. >> Dear Lord, we just need to buy your software, there nust be something >> done!! >> >> Thanks!! >> >> On Wed, Dec 15, 2021 at 10:54 PM Adam Armstrong via observium < >> observium(a)observium.org> wrote: >> >>> Hi Theodore, >>> >>> >>> >>> What’s the problem? >>> >>> >>> >>> We have limited ability to do much with the Paddle platform except for >>> cancel things, though. J >>> >>> >>> >>> Thanks, >>> >>> Adam. >>> >>> >>> >>> *From:* observium <observium-bounces(a)observium.org> *On Behalf Of *Thodoris >>> Lakiotis via observium >>> *Sent:* 15 December 2021 15:29 >>> *To:* Observium <observium(a)observium.org> >>> *Cc:* Thodoris Lakiotis <tlak(a)synapsecom.gr> >>> *Subject:* [Observium] Cannot buy Subscription for Professional version >>> >>> >>> >>> Hello Team!! >>> >>> I need help to address an issue with the renewal of our subscription >>> with Professional Observium. >>> >>> I cannot find resolution, so far, with paddle. >>> >>> Is there anybony could help me from Observium team? >>> >>> >>> >>> Thanks and Regards, >>> >>> >>> >>> Theodore >>> _______________________________________________ >>> observium mailing list >>> observium(a)observium.org >>> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >>> >> _______________________________________________ >> observium mailing list >> observium(a)observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >> >> >> _______________________________________________ >> observium mailing list >> observium(a)observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium >> >

1 0

Re: [Observium] add support for ASCO Transfer switch
by Tony Guadagno 16 Dec '21

16 Dec '21

Adam, happy to do that, can you give me the snmpwalk syntax you would like? It seems like transfer switches and generators are the worst mibs…but its all I have to go on. thanks Tony From: Adam Armstrong via observium Sent: Thursday, December 16, 2021 11:03 AM To: 'Observium' Cc: Adam Armstrong Subject: Re: [Observium] add support for ASCO Transfer switch Hi Tony, That’s something of a horrific MIB. It doesn’t use tables properly and has really bad oid numbering, so isn’t the easiest thing to support. You should probably open a jira and provide the mib along with an snmp walk in the format the ticket requests at https://jira.observium.org Adam. From: observium <observium-bounces(a)observium.org> On Behalf Of Tony Guadagno via observium Sent: 16 December 2021 13:37 To: Pisano, Anthony D. via observium <observium(a)observium.org> Cc: Tony Guadagno <tonyg(a)guadagno.org> Subject: [Observium] add support for ASCO Transfer switch Hi, could you please evaluate this mid. Currently you show the Asco icon but no other information. I would like to see transfer switch state etc. Let me know if you need anything else, I will be happy to gather logs. Thanks Tony

1 0

add support for ASCO Transfer switch
by Tony Guadagno 16 Dec '21

16 Dec '21

Hi, could you please evaluate this mid. Currently you show the Asco icon but no other information. I would like to see transfer switch state etc. Let me know if you need anything else, I will be happy to gather logs. Thanks Tony

2 1

Cannot buy Subscription for Professional version
by Thodoris Lakiotis 16 Dec '21

16 Dec '21

Hello Team!! I need help to address an issue with the renewal of our subscription with Professional Observium. I cannot find resolution, so far, with paddle. Is there anybony could help me from Observium team? Thanks and Regards, Theodore

3 3

what do you need to add support for a device?
by Tony Guadagno 15 Dec '21

15 Dec '21

Hi, I have a couple of devices that are under supported or not supported. I have manufacturers mibs for them, what else would you need to evaluate them for support? thanks Tony

1 0

question about wmi
by Tony Guadagno 15 Dec '21

15 Dec '21

Hi, I have enabled wmi on my install. I have tested my config with wmic and it seems to work. I have put the global parms in and I am not seeing any log messages about wmi. How do I know if wmi is being attempted? [2021/12/14 18:30:01 +0000] discovery.php(560036): /opt/observium/discovery.php: new - 0 devices discovered in 0.001 secs [2021/12/14 18:30:04 +0000] poller.php(560053): poller.php: abc-wolcott2.company.local - 1 devices polled in 2.943 secs [2021/12/14 18:30:07 +0000] poller.php(560051): poller.php: abc-lyo-sw-3.company.local - 1 devices polled in 5.134 secs [2021/12/14 18:30:07 +0000] poller.php(560049): poller.php: abc-observium.company.local - 1 devices polled in 5.509 secs [2021/12/14 18:30:12 +0000] poller.php(560047): UNIX-AGENT: Connection on tcp://abc-esx15.company.local:36602 failed. ERROR: 110 Connection timed out [2021/12/14 18:30:14 +0000] poller.php(560047): poller.php: abc-esx15.company.local - 1 devices polled in 12.67 secs [2021/12/14 13:30:14 -0500] poller-wrapper.py(560037): /opt/observium/poller-wrapper.py: processed 4 devices in 13.78 seconds with 4 threads, load average (5min) 0.13 Tony

3 2

alert box info
by Arnoldo Vidal Bravo 13 Dec '21

13 Dec '21

Hi, In the alert boxes... we can choose display a sysName or hostname?... -- Saluda cordialmente

1 0

M;onitoring Squid with Observium
by Hofer, Elmar (BITBW) 13 Dec '21

13 Dec '21

Dear list, I want to monitor my squid instances on snmp port 3401 udp with observium. But when I try to add the device (here squid on port 3401 udp) I don't get an answer. With cacti everything works well, an even with snmpwalk and snmp v1 I get an answer. How can I add squid to observium ? Help is always welcome. Thanks. Yours Elmar Hofer Systemspezialist Sicherheitstechnik BITBW IT Baden Württemberg Abteilung 3 Referat 31 - Operative Sicherheit Krailenshaldenstraße 44 70469 Stuttgart Telefon: +49 (0)711 8910-648 Fax: +49 (0)711 8910-97696 E-Mail: elmar.hofer(a)bitbw.bwl.de<mailto:elmar.hofer@bitbw.bwl.de> Internet: http://www.bitbw.de<http://www.bitbw.de/>

2 3

Rolling 11803
by Serghei Golipad 10 Dec '21

10 Dec '21

I've just updated to above to find out that Observium page doesn't load up (HTTP500), can see a lot of changes to PHP, anyone experienced the same? Thank you. PLEASE CONSIDER THE ENVIRONMENT BEFORE PRINTING THIS EMAIL. CDW Limited is a Company registered in England and Wales. This email is sent for and on behalf of CDW Finance Holdings Limited. CDW Finance Holdings Limited is the UK holding company for CDW Limited trading as CDW. The registered office for CDW Finance Holdings Limited (Company Number 05872067) and its UK group undertakings is 1 New Change, London, EC4M 9AF. VAT Registration 902 1949 39. Confidentiality: This e-mail contains proprietary information, some or all of which may be confidential and/or legally privileged. It is for the intended recipient only. If an addressing or transmission error has misdirected this e-mail, please notify the author by replying to this e-mail and then delete the original. If you are not the intended recipient you may not use, disclose, distribute, copy, print or rely on any information contained in this e-mail. You must not inform any other person other than CDW or the sender of its existence.>/p> For more information about CDW please visit https://www.uk.cdw.com

2 2

Need Assist in Syslog
by Rahul M 09 Dec '21

09 Dec '21

Hi Team, I had purchased the professional edition need assistance in the below-listed things. 1. Syslog Integration from IP-PHONES 2. How the Location works in observium 3. Alert checker

1 0

Información Licencia Enterprise (Observium).
by etrejo＠viginet.com.ve 08 Dec '21

08 Dec '21

Buenas tardes ! Saludos, este correo tiene como finalidad hacerles saber que en estos momentos estamos utilizando la versión Community desde hace tiempo para nuestra empresa; nuestras expectativas por los momentos es llegar a la versión Enterprise, por esta razón nos gustaría que nos canalicen esta información para poder concretar una sesión o algún contacto que nos pudiera guiar y poder exponer las dudas y requerimientos que tenemos en cuanto a la herramienta. Sin mas por el momento y esperando una pronta respuesta me despido. Atte.

1 0

add mib on observium
by Toky ANDRIANASOLO 08 Dec '21

08 Dec '21

Hello, could you please help us on how to add MIB observium Tky Thank you, -- <https://app.livestorm.co/comdata-group/automotive-technologies-leading-to-c…>

1 0

Missing some probes
by Peter Derissen 08 Dec '21

08 Dec '21

Hi all, Today i started looking add the nagios utils probes in Observium. Seems like im missing some probes in the pulldown menu. [cid:image001.png@01D7EB70.8A9A1FE0] [cid:image002.png@01D7EB70.8A9A1FE0] [cid:image003.png@01D7EB70.8A9A1FE0] check_ntp and check_dhcp cannot by found in the pulldown menu. Any way to add them? Kind regards, Met vriendelijke groet, Peter Derissen Eurofiber Nederland Network Engineer Safariweg 25-31 +31 (0)6 11587110 3605 MA Maarssen [cid:image004.png@01D7EB70.8A9A1FE0]<https://www.eurofiber.nl/> Volg ons op Twitter<https://twitter.com/Eurofiber> | Linkedin<https://www.linkedin.com/company/eurofiber> | Facebook<https://www.facebook.com/eurofiberNL/> | Youtube<https://www.youtube.com/channel/UC6DavgEm7-ktAD8_Co_qnMA> Wilt u op de hoogte blijven van technische ontwikkelingen aan ons netwerk, nieuwe ICT ontwikkelingen en klantervaringen? Meld u dan aan voor onze maandelijkse nieuwsbrief<https://marketing.eurofiber.com/acton/fs/blocks/showLandingPage/a/15570/p/p…>. [cid:image005.jpg@01D7EB70.8A9A1FE0]<https://www.eurofiber.nl/> ******** IMPORTANT NOTICE ******** This e-mail (including any attachments) may contain information that is confidential or otherwise protected from disclosure and it is intended only for the addressees. If you are not the intended recipient, please note that any copying, distribution or other use of information contained in this e-mail (and its attachments) is not allowed. If you have received this e-mail in error, kindly notify us immediately by telephone or e-mail and delete the message (including any attachments) from your system. Please note that e-mail messages may contain computer viruses or other defects, may not be accurately replicated on other systems, or may be subject of unauthorized interception or other interference without the knowledge of sender or recipient. Eurofiber only sends and receives e-mails on the basis that Eurofiber is not responsible for any such computer viruses, corruption or other interference or any consequences thereof. Eurofiber Nederland B.V. is registered in the Chamber of Commerce of Amsterdam with number 34134377, VAT number NL 8088.51.524 B01. Eurofiber N.V. has its registered office at Belgicastraat 5 bus 7, 1930 Zaventem and is registered under national number 0435.204.851. Eurofiber France has its registered office at 21 Avenue de la Cr?ativit?, 59650 Villeneuve d'Ascq and is registered under national number FR 83.822.249.074.

3 3

monitor VPN ipsec
by Toky ANDRIANASOLO 07 Dec '21

07 Dec '21

Hello, Could you please help us on how to import MIB for VPN ipsec fortigate on observium, we need to see more than operation status up/down speaking about VPN monitoring. Thank you and Regards, Toky -- <https://app.livestorm.co/comdata-group/automotive-technologies-leading-to-c…>

1 0

S2S Monitoring and Bandwidth Check
by Njoroge, Joyce (Stadt Ulm) 06 Dec '21

06 Dec '21

Hallo Darren, Thanks so much for that. That's very helpful. Regards, Joyce -----Ursprüngliche Nachricht----- Von: observium <observium-bounces(a)observium.org> Im Auftrag von observium-request(a)observium.org Gesendet: Samstag, 4. Dezember 2021 13:00 An: observium(a)observium.org Betreff: observium Digest, Vol 137, Issue 3 Send observium mailing list submissions to observium(a)observium.org To subscribe or unsubscribe via the World Wide Web, visit http://postman.memetic.org/cgi-bin/mailman/listinfo/observium or, via email, send a message with subject or body 'help' to observium-request(a)observium.org You can reach the person managing the list at observium-owner(a)observium.org When replying, please edit your Subject line so it is more specific than "Re: Contents of observium digest..." Today's Topics: 1. Re: S2S Monitoring and Bandwidth Check (Storer, Darren) ---------------------------------------------------------------------- Message: 1 Date: Sat, 4 Dec 2021 01:35:12 +0000 From: "Storer, Darren" <darren.storer(a)gmail.com> To: Observium <observium(a)observium.org> Subject: Re: [Observium] S2S Monitoring and Bandwidth Check Message-ID: <CAHBhi2GxfVRue5j1TZa-Py5jBdnSA4YnKXhC-2Zw4k3dAvEJjw(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" Hallo Joyce, Yes, Observium can display the bandwidth being used between two sites. If you are interested in the nature of the data flowing (e.g. destinations and protocols, etc.) then you probably need another tool like ntopng but only if your network equipment supports NetFlow/sFlow exports. To check bandwidth being used, typically you drill down to a specific port on a router or switch and display the data graphically that way. For data flowing between sites via a VPN, you may need to look at IPsec ports, rather than physical ports. Take a look under ports: https://upload.wikimedia.org/wikipedia/commons/a/ad/Observium-ports-march20… MfG Darren On Fri, 3 Dec 2021 at 11:13, Njoroge, Joyce (Stadt Ulm) via observium < observium(a)observium.org> wrote: > Hallo, > I have two questions that I would like to know whether it is possible > to do using Observium: > > 1. Is there a way to monitor the data that flows between site-to-site > locations? > 2. How can I check the bandwidth of a device that is already in > observium? > > Lastly, I understand that mapping is from a 3rd party provider > (OpenStreetMap), but would anyone have had a problem, whereby just > from nowhere locations, that were properly mapped, are not correctly > mapped anymore? A bunch of locations are showing in the middle of the sea. Thanks. > > Regards, > Joyce > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://postman.memetic.org/pipermail/observium/attachments/20211204/bf15b39…> ------------------------------ Subject: Digest Footer _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium ------------------------------ End of observium Digest, Vol 137, Issue 3 *****************************************

1 0

observium + oxidized, anyone test it?
by Torstein Eide 05 Dec '21

05 Dec '21

I found a repository with observium + oxidized. Has anyone tested it? https://github.com/colin-stubbs/observium-oxidized -- Torstein Eide Torsteine(a)gmail.com

1 0

S2S Monitoring and Bandwidth Check
by Njoroge, Joyce (Stadt Ulm) 05 Dec '21

05 Dec '21

Hallo, I have two questions that I would like to know whether it is possible to do using Observium: 1. Is there a way to monitor the data that flows between site-to-site locations? 2. How can I check the bandwidth of a device that is already in observium? Lastly, I understand that mapping is from a 3rd party provider (OpenStreetMap), but would anyone have had a problem, whereby just from nowhere locations, that were properly mapped, are not correctly mapped anymore? A bunch of locations are showing in the middle of the sea. Thanks. Regards, Joyce

3 2

Discovery of IPv6 only hosts
by r0m5 30 Nov '21

30 Nov '21

Hello, I have a problem addind IPv6 only hosts to observium using discovery. For example the "myserver" host in the extract below (part of the result of"/opt/observium/discovery.php -h all -dd") This "myserver" host is discovered as a LLDP neighbor of another host. Then discovery.php tries to connect to "myserver" with snmpget using its IPv6 address. But There are missing brackets in the snmpget command : - failing : /usr/bin/snmpget -v2c -c 'commu' -Pud -OQUsn -m SNMPv2-MIB -M /opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp 'udp6':'fde6:67ca:25ef:14::17':'161' .1.3.6.1.2.1.1.2.0.1.3.6.1.2.1.1.3.0 - would be OK (adding brackets) : /usr/bin/snmpget -v2c -c 'commu' -Pud -OQUsn -m SNMPv2-MIB -M /opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp 'udp6':'[fde6:67ca:25ef:14::17]':'161' .1.3.6.1.2.1.1.2.0.1.3.6.1.2.1.1.3.0 How could I solve this issue ? - is there a way to force observium to add brackets ? - or maybe even better to force observium to use the hostname "myserver" to connect using snmpget instead of the IPv6 address ? Regards ! ************************ ##### Module Start: neighbours ##### o LLDP-MIB [...] [139768400.45.41] => array( [lldpRemChassisIdSubtype] => string(10) "macAddress" [lldpRemChassisId] => string(18) "52 54 00 60 4E 17 " [lldpRemPortIdSubtype] => string(10) "macAddress" [lldpRemPortId] => string(18) "52 54 00 60 4E 17 " [lldpRemPortDesc] => string(4) "ens3" [lldpRemSysName] => string(37) "myserver.local.r0m5.eu" [lldpRemSysDesc] => string(95) "Debian GNU/Linux 11 (bullseye) Linux 5.10.0-9-amd64 #1 SMP Debian 5.10.70-1 (2021-09-30) x86_64" [lldpRemManAddrIfId] => string(1) "2" [lldpRemManAddr] => string(39) "fde6:66ba:24ff:0104:0000:0000:0000:0017" [lldpRemMan] => array( [fde6:66ba:24ff:0104:0000:0000:0000:0017] => array( [lldpRemManAddrIfId] => string(1) "2" ) ) ) [...] SQL[SELECT `device_id` FROM `devices` WHERE `hostname` = 'myserver.local.r0m5.eu'] ROWS[0] SQL RUNTIME[0.00016594s] SQL[SELECT `device_id` FROM `devices` WHERE `sysName` = 'myserver.local.r0m5.eu' AND `disabled` = '0'] ROWS[0] SQL RUNTIME[0.00020385s] SQL[SELECT `autodiscovery`.*, UNIX_TIMESTAMP(`last_checked`) AS `last_checked_unixtime` FROM `autodiscovery` WHERE `poller_id` = '0' AND `remote_hostname` = 'myserver.local.r0m5.eu' AND `remote_ip` = 'fde6:67ca:25ef:14::17'] ROWS[1] SQL RUNTIME[0.00026703s] AUTODISCOVERY DEVEL: hostname & ip DB found > $db_entry /opt/observium/includes/discovery/functions.inc.php:636 array( [autodiscovery_id] => string(1) "8" [poller_id] => string(1) "0" [device_id] => string(3) "150" [remote_hostname] => string(37) "myserver.local.r0m5.eu" [remote_ip] => string(22) "fde6:67ca:25ef:14::17" [remote_device_id] => null [protocol] => string(4) "LLDP" [added] => string(19) "2021-11-27 13:11:08" [last_checked] => string(19) "2021-11-28 12:37:37" [last_reason] => string(7) "no_snmp" [last_checked_unixtime] => string(10) "1638099457" ) Remote device checked 7m 26s ago (less than 1 day) o Trying to discover host myserver.local.r0m5.eu (fde6:67ca:25ef:14::17) through LLDP (xdp) /opt/observium/includes/common.inc.php:3679 array() > $dns6 /opt/observium/includes/common.inc.php:3685 array( [0] => array( [host] => string(37) "myserver.local.r0m5.eu" [class] => string(2) "IN" [ttl] => int(20876) [type] => string(4) "AAAA" [ipv6] => string(22) "fde6:67ca:25ef:14::17" ) ) Host myserver.local.r0m5.eu resolved as fde6:67ca:25ef:14::17 Host myserver.local.r0m5.eu (fde6:67ca:25ef:14::17) founded inside configured nets, trying to add: CMD[/usr/bin/fping6 -t 500 -c 1 -q fde6:67ca:25ef:14::17 2>&1] CMD EXITCODE[0] CMD RUNTIME[0.0195s] CMD EXITDELAY[10ms] STDOUT[ fde6:67ca:25ef:14::17 : xmt/rcv/%loss = 1/1/0%, min/avg/max = 17.2/17.2/17.2 ] SQL[SELECT `hostname` FROM `ipv6_addresses` LEFT JOIN `devices` USING(`device_id`) WHERE `disabled` = 0 AND `ipv6_binary` = '��f�$�\0\0\0\0\0\0\0' LIMIT 1] ROWS[0] SQL RUNTIME[0.00051618s] /opt/observium/includes/entities/device.inc.php:54 array( *[hostname] => string(22) "fde6:67ca:25ef:14::17"* [snmp_port] => int(161) [snmp_transport] => string(4) "udp6" [snmp_version] => string(3) "v2c" [snmp_community] => string(4) "commu" ) Trying v2c community commu ... CMD[/usr/bin/snmpget -v2c -c 'commu' -Pud -OQUsn -m SNMPv2-MIB -M /opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp 'udp6':'fde6:67ca:25ef:14::17':'161' .1.3.6.1.2.1.1.2.0 .1.3.6.1.2.1.1.3.0] CMD EXITCODE[1] CMD RUNTIME[6.0132s] STDOUT[ ] STDERR[ Timeout: No Response from udp6:fde6:67ca:25ef:14::17:161. ] SNMP ERROR - device: , cmd: snmpget, options: -OQUsn, mib: 'SNMPv2-MIB', oid: '.1.3.6.1.2.1.1.2.0 .1.3.6.1.2.1.1.3.0', cmd exitcode: 1, snmp error code: #900, reason: 'isSNMPable', runtime: 6.01322889328 SNMP ERROR - device: , cmd: snmpget, options: -OQUsn, mib: 'SNMPv2-MIB', oid: '.1.3.6.1.2.1.1.2.0 .1.3.6.1.2.1.1.3.0', cmd exitcode: 1, snmp error code: #900, reason: 'isSNMPable', runtime: 6.01322889328 SNMP STATUS[FALSE]

3 4

Cannot get info of Virtual-access CISCO
by Sébastien 65 28 Nov '21

28 Nov '21

Hello, I cannot get/graph the interfaces virtual-access (Vi2.X) of a CISCO ASR1001... Virtual-Access interfaces are in PPPoVPDN mode (ASR is an LNS). Do I have to configure a specific module to retrieve information from Virtual-Access ? Thank you !

2 3

Re: [Observium] Issue in monitoring the API service of Checkpoint Multi Domain Management server.
by SOC.HCL 26 Nov '21

26 Nov '21

Hi Adam, As per below mail trail , please help to find answers of below queries : What is the meaning system it's installed on is too old, too ? What is the meaning of Newer distribution ? I logged in web session of Observium then about Observium but it is showing [cid:image002.png@01D7E2C9.2E8AC830] Is there any other way to check the Observium Version ? Regards, Narender Verma Associate Consultant - HCL Nordea | Infrastructure - Security Mob: +91 8447000611 Manager: Nitin Garg E-mail: narender.verma(a)consult.nordea.com Planned Leave : 10,11 August 2021 Availibility: 8:00 AM to 5 PM CET, Team DL : dlcomSecurity_HCL(a)nordea.com<mailto:dlcomSecurity_HCL@nordea.com> Confidential From: Adam Armstrong <adama(a)observium.org> Sent: Wednesday, November 24, 2021 8:41 PM To: SOC.HCL <SOC.HCL(a)nordea.com> Subject: RE: [Observium] Issue in monitoring the API service of Checkpoint Multi Domain Management server. What version are you running? It seems you have some strange broken install that doesn't even know its own version. The system it's installed on is too old, too. You need to reinstall on a newer distribution. Thanks, Adam. From: SOC.HCL <SOC.HCL(a)nordea.com<mailto:SOC.HCL@nordea.com>> Sent: 24 November 2021 08:58 To: Observium <observium(a)observium.org<mailto:observium@observium.org>> Cc: Adam Armstrong <adama(a)observium.org<mailto:adama@observium.org>>; dlcom Security_HCL <dlcomSecurity_HCL(a)nordea.com<mailto:dlcomSecurity_HCL@nordea.com>> Subject: RE: [Observium] Issue in monitoring the API service of Checkpoint Multi Domain Management server. Hi Team, Firstly the probe option is not coming on our Observium. Please help to get it enabled in observium so we can explore options in the probe setting to monitor the service. Regards, Narender Verma Associate Consultant - HCL Nordea | Infrastructure - Security Mob: +91 8447000611 Manager: Nitin Garg E-mail: narender.verma(a)consult.nordea.com<mailto:narender.verma@consult.nordea.com> Planned Leave : 10,11 August 2021 Availibility: 8:00 AM to 5 PM CET, Team DL : dlcomSecurity_HCL(a)nordea.com<mailto:dlcomSecurity_HCL@nordea.com> Confidential From: observium <observium-bounces(a)observium.org<mailto:observium-bounces@observium.org>> On Behalf Of Adam Armstrong via observium Sent: Friday, November 19, 2021 9:18 PM To: 'Observium' <observium(a)observium.org<mailto:observium@observium.org>> Cc: Adam Armstrong <adama(a)observium.org<mailto:adama@observium.org>> Subject: Re: [Observium] Issue in monitoring the API service of Checkpoint Multi Domain Management server. I have absolutely no idea what any of this is. Adam. From: observium <observium-bounces(a)observium.org<mailto:observium-bounces@observium.org>> On Behalf Of SOC.HCL via observium Sent: 19 November 2021 08:16 To: observium(a)observium.org<mailto:observium@observium.org> Cc: SOC.HCL <SOC.HCL(a)nordea.com<mailto:SOC.HCL@nordea.com>>; Garg, Nitin <nitin.garg(a)consult.nordea.com<mailto:nitin.garg@consult.nordea.com>>; Verma, Narender <narender.verma(a)consult.nordea.com<mailto:narender.verma@consult.nordea.com>>; Sharma, Yogesh Kumar <yogesh.kumar.sharma(a)consult.nordea.com<mailto:yogesh.kumar.sharma@consult.nordea.com>> Subject: [Observium] Issue in monitoring the API service of Checkpoint Multi Domain Management server. Hi Team, This communication is for monitoring the API service of Checkpoint Multi Domain Management server. Current Setup: Observium: [cid:image003.png@01D7E2C9.2E8AC830] Checkpoint Multi Domain Management Server: Checkpoint R80.40 Take 120 . API Port Details : Port Details: ------------------- JETTY Internal Port: 50276 Please help to get the API service monitored by Observium. Regards, Narender Verma Associate Consultant - HCL Nordea | Infrastructure - Security Mob: +91 8447000611 Manager: Nitin Garg E-mail: narender.verma(a)consult.nordea.com<mailto:narender.verma@consult.nordea.com> Planned Leave : 10,11 August 2021 Availibility: 8:00 AM to 5 PM CET, Team DL : dlcomSecurity_HCL(a)nordea.com<mailto:dlcomSecurity_HCL@nordea.com> Confidential

1 0

Issue in monitoring the API service of Checkpoint Multi Domain Management server.
by SOC.HCL 24 Nov '21

24 Nov '21

Hi Team, This communication is for monitoring the API service of Checkpoint Multi Domain Management server. Current Setup: Observium: [cid:image001.png@01D7DD4B.C4F7F870] Checkpoint Multi Domain Management Server: Checkpoint R80.40 Take 120 . API Port Details : Port Details: ------------------- JETTY Internal Port: 50276 Please help to get the API service monitored by Observium. Regards, Narender Verma Associate Consultant - HCL Nordea | Infrastructure - Security Mob: +91 8447000611 Manager: Nitin Garg E-mail: narender.verma(a)consult.nordea.com Planned Leave : 10,11 August 2021 Availibility: 8:00 AM to 5 PM CET, Team DL : dlcomSecurity_HCL(a)nordea.com Confidential

2 2

Adding devices on a partitioned poller
by Lars Joergensen 22 Nov '21

22 Nov '21

Hi I have tried to add a device to a partitioned poller, but nothing happens. I can see it in the Poller Actions window, but it seems like it never gets picked up by the poller. Am I doing something wrong? [cid:image001.png@01D7DE04.8B385800] Lars ________________________________ Disclaimer: This e-mail, including any attachments, is for the intended recipient only. If you have received this e-mail by mistake please notify the sender immediately by return e-mail and delete this e-mail and any attachments, without opening the attachments, from your system. Access, disclosure, copying, distribution or reliance on any part of this e-mail by anyone else is prohibited. This e-mail is confidential and may be legally privileged. Chr. Hansen does not represent and/or warrant that the information sent and/or received by or with this e-mail is correct and does not accept any liability for damages related thereto. https://www.chr-hansen.com/en/legal-notice

5 4

Best SNMP configuration for CISCO switch and router
by Sébastien 65 20 Nov '21

20 Nov '21

Hello list, What is the best SNMP configuration to use to feed back information from switch (Catalyst) and router (ASR) ? I use the following configuration on my equipment but I wonder if there is not better (MIB) : snmp-server group READONLY v3 priv read MIB-2 snmp-server view MIB-2 iso included Thanks !

4 7