- observium - lists.observium.org

Voltage/Current Sensor anomalies on Cisco SG200/SF300 switches
by Serge Caron 01 May '19

01 May '19

Greetings! I have a number of SF300-24P (802.3af), SF300-24PP (802.3at), SF300-48P, and SG200-26P Cisco switches, all at firmware revision 1.4.8.6 (There is a newer firmware 1.4.10.06 published 4 days ago: I will install this only if required). The voltage/current sensors are constantly complaining that they are either under/over threshold. For example, below are the logs on a port drawing 3500 mW for a Ubiquiti Unifi access point model UAP-AC-M: voltage range from 0V (!) to 92V for a device that should draw 37 to 57 V PoE levels. I have 29 of these devices scattered over the network and I can rule out simple malfunction of any/all devices. More intriguing is the 0.0975A current "threshold" used to issue these warnings: it does not make sense if Watts are still the product of Volts by Ampps ;-). Is it possible that the MiB for these devices is out of whack? I recently updated my Observium CE to 18.9.9420 (5th September 2018) but this issue has been annoying me for quite some time. Please note that I have similar results for all kinds of IP cameras : however, I do not have issues for ports that are connected to Cisco SG200-08 PoE switches and for which the only warnings I get is when the output voltage suddenly drops to zero. Unfortunately, these devices do not support SNMP. Kind regards, Serge Caron 2019-04-29 21:02:10 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 92 V (> 60.95 V) 2019-04-29 20:20:49 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 90 V (> 60.95 V) 2019-04-29 20:00:37 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 92 V (> 60.95 V) 2019-04-29 19:35:24 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 81 V (> 60.95 V) 2019-04-29 18:07:02 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 30 V (< 45.05 V) 2019-04-29 17:57:25 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 31 V (< 45.05 V) 2019-04-29 17:50:40 fa14 PoE Current Current fa14 PoE Current above threshold: 0.139 A (> 0.0975 A) 2019-04-29 17:46:41 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 31 V (< 45.05 V) 2019-04-29 17:00:36 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 31 V (< 45.05 V) 2019-04-29 16:52:34 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 31 V (< 45.05 V) 2019-04-29 15:07:18 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 84 V (> 60.95 V) 2019-04-29 14:57:19 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 80 V (> 60.95 V) 2019-04-29 14:42:43 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 62 V (> 60.95 V) 2019-04-29 14:42:43 fa14 PoE Current Current fa14 PoE Current above threshold: 0.113 A (> 0.0975 A) 2019-04-29 14:22:06 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 31 V (< 45.05 V) 2019-04-29 14:22:06 fa14 PoE Current Current fa14 PoE Current above threshold: 0.112 A (> 0.0975 A) 2019-04-29 14:10:37 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 92 V (> 60.95 V) 2019-04-29 13:47:30 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 38 V (< 45.05 V) 2019-04-29 13:22:27 fa14 PoE Current Current fa14 PoE Current above threshold: 0.112 A (> 0.0975 A) 2019-04-29 13:05:35 fa14 PoE Current Current fa14 PoE Current above threshold: 0.114 A (> 0.0975 A) 2019-04-29 12:41:57 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 0 V (< 45.05 V) 2019-04-29 12:25:23 fa14 PoE Current Current fa14 PoE Current above threshold: 0.112 A (> 0.0975 A) 2019-04-29 11:21:58 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 90 V (> 60.95 V) 2019-04-29 10:52:05 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 32 V (< 45.05 V) 2019-04-29 10:46:03 fa14 PoE Current Current fa14 PoE Current above threshold: 0.11 A (> 0.0975 A) 2019-04-29 10:30:36 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 39 V (< 45.05 V) 2019-04-29 10:25:34 fa14 PoE Current Current fa14 PoE Current above threshold: 0.11 A (> 0.0975 A) 2019-04-29 10:00:24 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 82 V (> 60.95 V) 2019-04-29 09:06:30 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 33 V (< 45.05 V) 2019-04-29 08:55:46 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 104 V (> 60.95 V) 2019-04-29 08:40:50 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 90 V (> 60.95 V) 2019-04-29 07:37:17 fa14 PoE Current Current fa14 PoE Current above threshold: 0.11 A (> 0.0975 A) 2019-04-29 07:16:51 fa14 PoE Voltage Voltage fa14 PoE Voltage under threshold: 32 V (< 45.05 V) 2019-04-29 07:07:29 fa14 PoE Current Current fa14 PoE Current above threshold: 0.11 A (> 0.0975 A) 2019-04-29 07:00:34 fa14 PoE Voltage Voltage fa14 PoE Voltage above threshold: 84 V (> 60.95 V)

2 3

Billing Module
by Gabriel Cambronero 30 Apr '19

30 Apr '19

Hello Is there a way that we can add "Alert Checkers" for this module? I look forward to hearing back from you. Best Regards, -- [image: https://www.racknation.cr/firma.jpg] * Gabriel Cambronero S* * Infrastructure Manager* * RACKNATION Costa Rica* Email: gcambronero(a)racknation.cr Tel: (506) 4000-2133 Cel: (506) 8813-3048 http://www.RackNation.cr <http://www.racknation.cr/> This email and any attachments to it may be confidential and are intended solely for the use of the individual to whom it is addressed. Any views or opinions expressed are solely those of the author and do not necessarily represent those of Racknation. If you are not the intended recipient of this email, you must neither take any action based upon its contents, nor copy or show it to anyone. Please contact the sender if you believe you have received this email in error. Este mensaje y cualquier archivo adjunto son confidenciales y pueden contener información privilegiada o estar protegidos de alguna forma contra su divulgación. Cualquier punto de vista u opiniones expresadas son exclusivas del autor y no representan necesariamente las de Racknation. Si usted no es el destinatario previsto, no debe copiar este mensaje ni ninguno de sus archivos adjuntos, como tampoco informar sobre su contenido a ninguna otra persona. Si ha recibido esta transmisión por error, rogamos que lo comunique inmediatamente al remitente y elimine de su sistema el mensaje y todos los archivos adjuntos que éste pueda contener.

1 0

VRRP
by Christian Eriksson 30 Apr '19

30 Apr '19

Hi, Are there any plans in monitoring VRRP on devices and map it to the alerting system? Vänliga hälsningar / Best regards, [Advania_Trappa_CMYK] Christian Eriksson System Consultant [cid:image003.png@01D4FF4C.9FF22170]<mailto:christian.eriksson@advania.com>[Advania-Bikupa Facebook]<https://www.facebook.com/advania.se/>[Advania-Bikupa LinkedIn]<https://www.linkedin.com/company/advania-ab/> +4641090488<tel:+4641090488> | +46761400400<tel:+46761400400> www.advania.se<http://www.advania.se/> | Stockholm<https://www.google.se/maps/place/Advania+Sverige+AB/@59.3062176,18.0278762,…> Ledande på att skapa kundnöjdhet [En bild som visar skärmbild Beskrivning genererad med hög exakthet]

3 3

Strange behavior traffic accounting
by Vladimir R 29 Apr '19

29 Apr '19

Hello. I am faced with a strange traffic accounting system behavior. The system displays different values of the allowed value in the "Bill Summary" (7Gbps) and "Historical Usage" for April (1.2Gbps). Illustration on the screenshot in the attachments. Please help understand why different values are displayed. -- The best regards! Vladimir R.

1 1

apcupsd UPS monitoring
by Nagy Attila 27 Apr '19

27 Apr '19

Hi All, we have a few Linux servers which are fed through APC Smart UPSs. Rather small ones, so no network management card, they are being monitored by apcupsd. We would be very happy to see the/some values of the UPSs in Observium. What I've done: I extended snmpd with a script from https://github.com/jirutka/apcupsd-snmp which makes some values from apcupsd available under |.1.3.6.1.4.1.318.1.1.1| which in turn belongs to PowerNet-MIB (aka APC). I can read those values with snmpwalk (see p.s.) so the script works. Observium already contains PowerNet-MIB, but no graph for these values are appearing. I suppose Observium does not query for PowerNet-MIB for anything other than APC OS, or maybe it looks for some other conditions as well? My question: is there a way to make Observium query and use these values for other OS's (like Linux) as well ? Regards, Tylla Ps: please feel free to correct any bad assumption/statement I made! Ps: here is my current output (MIB errors excluded) from snmpwalk in case it helps: snmpwalk -m ALL -v 2c -c public localhost .1.3.6.1.4.1.318.1.1.1 PowerNet-MIB::upsBasicIdentModel.0 = STRING: "Smart-UPS 750" PowerNet-MIB::upsBasicIdentName.0 = STRING: "test" PowerNet-MIB::upsAdvIdentFirmwareRevision.0 = STRING: "COM 02.1 / UPS.05.I" PowerNet-MIB::upsAdvIdentSerialNumber.0 = STRING: "AS1108112010" PowerNet-MIB::upsBasicBatteryTimeOnBattery.0 = Timeticks: (0) 0:00:00.00 PowerNet-MIB::upsAdvBatteryCapacity.0 = Gauge32: 100 PowerNet-MIB::upsAdvBatteryRunTimeRemaining.0 = Timeticks: (144000) 0:24:00.00 PowerNet-MIB::upsAdvBatteryNominalVoltage.0 = INTEGER: 24 PowerNet-MIB::upsAdvBatteryActualVoltage.0 = INTEGER: 27 PowerNet-MIB::upsBasicOutputStatus.0 = INTEGER: onLine(2) PowerNet-MIB::upsAdvConfigAlarm.0 = INTEGER: never(3) PowerNet-MIB::upsAdvConfigLowBatteryRunTime.0 = Timeticks: (30000) 0:05:00.00

2 3

Point me to "bulk changes" document
by Dana Bostic 26 Apr '19

26 Apr '19

Is there a document somewhere that will show me how to make "bulk" changes. An example would be how do I change a sensors Warn level for all my UPSs? I don't want to go though 200 of them, I want to change the default warning, etc. Caterpillar: Confidential Green

2 1

Bulk group creation via API/DB query/something else?
by Brandwatch NOC 26 Apr '19

26 Apr '19

Hi, I need to bulk create a large number of sensor groups. I would really rather not do that by hand in the GUI. Any automatable method would be fine - API/script/DB query/something else. I had a quick look around but couldn't find anything in the documentation - I would appreciate a quick nudge in the right direction. Thanks, Chris -- Chris Tomkins | Senior Network Engineer (Linux/Network) christ(a)brandwatch.com Office: +44 (0)1273 448 949 NEW YORK | BOSTON | BRIGHTON | LONDON | BERLIN | STUTTGART | SINGAPORE | SYDNEY | PARIS <https://www.brandwatch.com/blog/brandwatch-and-crimson-hexagon/>

2 2

Migrated from 16.04 to 18.04 and rrd stopped writing?
by Simon Mousey Smith 24 Apr '19

24 Apr '19

Hi All Im trying to find out if I have done something wrong or maybe missed something? I have done a migrate from ubuntu 16.04 to ubuntu 18.04 and now ALL of my RRDs have stopped being written? 1. mysqldump to backup, scp file to new server, then mysql to restore 2. Scp the whole rrd folder from old server to new server 3. Scp the old config.php to new server Only thing I have done differently is use the setup script instead of manually installing observium On the new server the rrd folder shows drwxrwsr-x 60 observium www-data 4.0K Apr 24 16:29 rrd But the old server shows it as drwxr-xr-x 60 www-data www-data 12K Apr 24 15:57 rrd One of the folders inside rrd show this drwxr-xr-x 2 root www-data 4096 Apr 24 15:58 localhost And an rrd file shows this -rw-r--r-- 1 root www-data 115K Apr 24 15:58 perf-poller.rrd Did I overwrite the folder permissions by accident? Regards Simon - Hestor Ltd

1 1

problems Graphs
by Victor Marinho 24 Apr '19

24 Apr '19

Good morning, the observium graphics are getting this way what can it be? [image: image.png] -- Victor Marinho *Soft House Net* Fone: 34 3241-6536 // 3241-3400 Celular: 34 98813-9966

3 2

MIBs FiberHome OLT not get data
by San Rollheiser 24 Apr '19

24 Apr '19

Hi guys, i have a OLT FiberHome model AN5516-01. I see in the Observium have the MIB, but when im trying get the data nothing happen. Im test other solution named LibreNMS and have this MIBs ( https://github.com/librenms/librenms/tree/master/mibs/fiberhome) and work fine... Any idea why this happen? Thx. BR Santiago

2 1

Cisco C2960X - PoE Power Monitoring Issue?
by Adam Ward 19 Apr '19

19 Apr '19

Hello, I am seeing an issue where power reported is lower for a given port, and I am seeing -nan for values in the graphs for a Cisco C2960X device. How do I troubleshoot inside OBS? #sh power inline gigabitEthernet 1/0/40 Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi1/0/40 auto on 15.4 Polycom Trio 8800 4 30.0 Interface AdminPowerMax AdminConsumption (Watts) (Watts) ---------- --------------- -------------------- Gi1/0/40 30.0 15.4 See attached screenshot from OBS. Adam Ward Systems Engineer Shamrock Trading Corporation Office Phone/Fax: (913) 310-2247 Email: award(a)shamrocktradingcorp.com<mailto:award@shamrocktradingcorp.com> Website: www.shamrocktradingcorp.com<http://www.shamrocktradingcorp.com/> This e-mail communication (including any attachments) is intended only for use by the individual or entity named above and is considered confidential. If you are not the intended recipient, or the employee or agent responsible to deliver it to the intended recipient, you should immediately stop reading this message and delete it from your system. Any unauthorized reading, distribution, copying or other use of this communication (or its attachments) is strictly prohibited.

3 4

Graph Widget Legend
by Brian Weeks 19 Apr '19

19 Apr '19

How can I get the front page Graph Widget to show the legend? I have had no luck enabling the legend on the graph page and then telling it to add to a dashboard it just does not show. As a matter of fact, the URL for the widget says legend=no. The legend is very important for us to know exactly how much bandwidth is being used on a particular link. -- Brian Weeks Network Engineer CCNA, MCSE, ACMT, A+, Network+, Security+ Brenham ISD 1301 Niebuhr St. Brenham, TX 7783 Office: (979) 277-3760 ext. 2249 Email: bweeks(a)brenhamk-12.net Website: http://www.brenhamisd.net --

2 1

Alert Checkers import
by Joelly, Alexander 19 Apr '19

19 Apr '19

Hello, It's possible to export the Alert Checkers on the CE version but I'm not finding an import on the Enterprise version, is there a cli tool for import? Thanks, Alex

2 1

seems i got something broken with geolocation
by Joelly, Alexander 18 Apr '19

18 Apr '19

during setup of distribution and partitioned poller, autodiscovery and mapquest I obviously did something wrong and messed up the geolocation feature - newly added devices are all only added to the default location. /opt/observium/logs/db.log on all pollers gets filled with: [2019/04/18 20:57:44 +0000] discovery.php(17511): Failed dbQuery (#1054 - Unknown column 'devices.location_id' in 'where clause'), Query: SELECT `device_id` FROM `devices` WHERE ( `devices`.`location_id` = '9') Thanks, Alex

1 0

Apache log path incorrect
by Joelly, Alexander 18 Apr '19

18 Apr '19

Hello, Just wanted to mention that the apache config file generated/installed from install script has an incorrect access and error log destination set. Should be: ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined instead: ErrorLog /error.log CustomLog /access.log combined Thanks, Alex

1 0

Alert Status widget mouseover popup on Dashboard
by Joelly, Alexander 17 Apr '19

17 Apr '19

Hello, On the Dashboard in the Alerts Status widget the mouseover popups for the 'Failed Tests' (small blue icon with the 'I') is not working - when going to the Alerts page it's working there. In the global settings the mouseover popups is enabled. Is that a known or already fixed issue or something on my side not set properly? r9774 Thanks, Alex

2 3

alerts in latest community version
by Tony Guadagno 17 Apr '19

17 Apr '19

Hi, I am currently using the current ce version (Observium CE 18.9.9420). After upgrading, i see the alerts have completely changed. the alerts i had still seem to function, but when I try to modify them, the fields are all different....I am getting the impression that there is an alert conversion script? I have looked for docs on how to use the new alerts but cannot find any. Can you please point me to a page that explains how to use the new alerts and how to fix the upgraded alerts. thanks!

1 0

Alert Status widget mouseover popup on Dashboard
by Joelly, Alexander 17 Apr '19

17 Apr '19

Hello, On the Dashboard in the Alerts Status widget the mouseover popups for the 'Failed Tests' (small blue icon with the 'I') is not working - when going to the Alerts page it's working there. In the global settings the mouseover popups is enabled. Is that a known or already fixed issue or something on my side not set properly? r9774 Thanks, Alex

1 0

No RAM graphs are displayed for network devices
by Vladimir R 16 Apr '19

16 Apr '19

Hello. I have observium version 19.3.9791. Apparently, earlier it was possible to monitor the amount of occupied RAM on network devices. In the application there is a screenshot which shows that there were such graph on the device. On new devices there are no such graphs. How can I fix this? Perhaps there is not enough parameter in the configuration? -- The best regards! Vladimir R.

4 6

how do you remove an association?
by Rowlands Mark 15 Apr '19

15 Apr '19

Running svn version. I just can't seem to find out how to remove an association for a custom oid.

1 0

Re: [Observium] Cisco ASA IPSec tunnels
by David Jesus Maturano Sanchez 11 Apr '19

11 Apr '19

This isn’t supported by ASA, there’s no way to do that for IPSec tunnels. David M. De: observium <observium-bounces(a)observium.org> en nombre de Johnathon Voegeli via observium <observium(a)observium.org> Responder a: Observium <observium(a)observium.org> Fecha: viernes, 1 de marzo de 2019, 11:38 Para: Observium <observium(a)observium.org> CC: Johnathon Voegeli <jvoegeli(a)voigtie.com> Asunto: [Observium] Cisco ASA IPSec tunnels Hey guys, Does anyone know where to set the “tunnel name” in a Cisco ASA or more rather where Observium gets that info? I have a dozen or so IPSec tunnels built, but Obs calls them all by the outside interface IP I suspect because I am too dense to figure out where its getting the tunnel name field from? [cid:image001.png@01D4D02B.AA8D38E0] The local address and the tunnel name are all the same.

2 1

OBS Integration with NFSen
by Ryan Huff 11 Apr '19

11 Apr '19

I -think-, I have NFSen integration with OBS working correctly, but I'm not clear on where I can see the flow graphs in OBS. I assume under the Graphs tab on the device page? Thanks, Ryan Huff, CCDP, CCNP Cisco Certified Network and Design Professional

5 7

Alert Checker question
by Tim Grossner 11 Apr '19

11 Apr '19

I have an Observium question - I am looking to create an alert for Palo Alto Networks firewall's session count, ideally one that fires when the session percentage goes above 85%. How would I build such a checker? I have tested a couple of different ways, and not been able to get one to fire. The MIB contains references such as: panSessionUtilization OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Session table utilization percentage. Values should be between 0 and 100." ::= { panSession 1 } ...can I build an alert based on panSessionUtilization? -- [image: GuidePoint Security] <http://www.guidepointsecurity.com> *Tim Grossner,* Engineer II *GuidePoint Security LLC* | Your Mission. Secured. *w* (877) 889-0132 x7605 *m* (636) 542-8464 *e* tim.grossner(a)guidepointsecurity.com Follow us! LinkedIn <http://www.linkedin.com/company/guidepoint-security> | Twitter <https://twitter.com/GuidePointSec> | Facebook <https://www.facebook.com/GuidePointSec> | Google+ <https://plus.google.com/+Guidepointsecurity/posts> | YouTube <https://www.youtube.com/channel/UCkajuS7JqEN3UGy6SXVhnfg> *GuidePoint Security recognized as recipient of 2018 Splunk Partner+ Awards! Read more <https://www.guidepointsecurity.com/2018/03/05/guidepoint-security-recognize…>* Confidentiality Notice: This communication constitutes an electronic communication within the meaning of the Electronic Communications Privacy Act, 18 U.S.C. Section 2510, and its disclosure is strictly limited to the recipient intended by the sender of this message. This transmission, and any attachments, may contain confidential information and work product(s). If you are not the intended recipient, any disclosure, copying, distribution or use of any of the information contained in or attached to this transmission is STRICTLY PROHIBITED. Please contact us immediately by return e-mail or call (877) 889-0132 <(877)%2520889-0132> option 5, and destroy the original transmission and its attachments without reading or saving in any manner.

2 1

RRD, Interfaces & docker
by Eduardo Costa 11 Apr '19

11 Apr '19

Hi all, This is my first post, and I'm a not so newbie user of Observium. If my question has been answered, or if its now correct, please advise. We're using Observium latest community edition as below: [cid:image001.png@01D4EFC3.4368A660] Situation: where monitoring a lot of virtual servers in a VMware environment, and we use docker in a lot of those vm's. What's happens is, as usual in docker, a lot of network devices are created, and observium correctly detects those ports. However in a small period of time they're gone, however Observium keep track of them, and keep the RRD files. In a specific case, we've got : [cid:image002.png@01D4EFC3.4368A660] Result... RRD for this server as... 200G! Anyone has had this problem? I was thinking about using the config['bad_if'][] with something similar of veth*, but I think is not possible. [cid:image003.png@01D4EFC3.899F0BB0] Any advice would be quite helpful! Thanks, EC _________________________________________________________________________ Eduardo Costa Administrador de Sistemas AIRC - Associação de Informática da Região Centro Coimbra iParque, Lote nº 15 3040-540 Antanhol - Coimbra +351-239-850569 | Direto +351-239-850599 | Fax eduardo.costa(a)airc.pt<mailto:eduardo.costa@airc.pt> | e-Mail

2 4

Re: [Observium] Kohler Generators
by Tony Guadagno 10 Apr '19

10 Apr '19

hi, I just installed a Kohler generator with a snmp-ethernet adapter. Observium does not have any specific knowledge of it. I have the company provided mib, could you add the mib to Observium? How do I provide the information to you? thanks Tony

2 2