- observium - lists.observium.org

Re: [Observium] New install no graphs
by Josh Hopper 13 Dec '13

13 Dec '13

Verify cron and your SNMP.conf file. It took a discovery poller and time before mine populated. Vmman <vmman50(a)gmail.com> wrote: Thank you I'm monitoring a device that I did not not setup, spoke too soon on the graphs. I think my cron job is not working correctly. After doing the chmod on the rrd directory I did a polling manually and now I see memory, processor, temp reading but no graphs. So close Mark On Thu, Dec 12, 2013 at 2:37 PM, Josh Hopper <joshhopper(a)protectplus.com<mailto:joshhopper@protectplus.com>> wrote: Add a sysContact to your switch and add it on the device in observium. Click the gear when drilled down to a device. Just the switch one is required but both helps in rare cases. Also, my pleasure. Vmman <vmman50(a)gmail.com<mailto:vmman50@gmail.com>> wrote: Joshua thank you very much, that seems to have worked. Sorry to bug you I have another question I'm monitoring a Cisco switch, how do you get the location correct on the global map? Mark On Thu, Dec 12, 2013 at 1:34 PM, Josh Hopper <joshhopper(a)protectplus.com<mailto:joshhopper@protectplus.com>> wrote: You have the same issue I just fixed. Chmod 775 on your rrd folder and make sure you have your cron setup correctly (bottom of the install guide). -- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image001.jpg@01CEF74F.A95B40D0] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160<tel:828-449-1839x2160> | Cell: 828-855-7565<tel:828-855-7565> From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Vmman Sent: Thursday, December 12, 2013 3:19 PM To: observium(a)observium.org<mailto:observium@observium.org> Subject: [Observium] New install no graphs I'm a beginner, installed observium on Centos 6.5 64bit, I am able to see my device but no graphs. This is what i'm seeing , any help would greatly be appreciated, Thanks Mark [cid:image002.png@01CEF74F.A95B40D0] _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

3 5

Re: [Observium] sponsoring a feature request.
by Aaron Daniels - Lists 13 Dec '13

13 Dec '13

Thanks Gents, Aaron -------- Original message -------- From: Nikolay Shopik <shopik(a)inblock.ru> Date: 13/12/2013 8:07 AM (GMT+10:00) To: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] sponsoring a feature request. Hey Aaron jira.observium.org - is better place On 13 дек. 2013 г., at 1:03, "Aaron Daniels - Lists" <lists(a)daniels.id.au> wrote: >> Please do not post patches to the list. >> >> Adam. >> > > Sorry Adam, > What is the process for contributing code to the project? > > Thanks, > Aaron > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium _______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] New install no graphs
by Josh Hopper 12 Dec '13

12 Dec '13

Add a sysContact to your switch and add it on the device in observium. Click the gear when drilled down to a device. Just the switch one is required but both helps in rare cases. Also, my pleasure. Vmman <vmman50(a)gmail.com> wrote: Joshua thank you very much, that seems to have worked. Sorry to bug you I have another question I'm monitoring a Cisco switch, how do you get the location correct on the global map? Mark On Thu, Dec 12, 2013 at 1:34 PM, Josh Hopper <joshhopper(a)protectplus.com<mailto:joshhopper@protectplus.com>> wrote: You have the same issue I just fixed. Chmod 775 on your rrd folder and make sure you have your cron setup correctly (bottom of the install guide). -- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image001.jpg@01CEF74F.A95B40D0] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160<tel:828-449-1839x2160> | Cell: 828-855-7565<tel:828-855-7565> From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Vmman Sent: Thursday, December 12, 2013 3:19 PM To: observium(a)observium.org<mailto:observium@observium.org> Subject: [Observium] New install no graphs I'm a beginner, installed observium on Centos 6.5 64bit, I am able to see my device but no graphs. This is what i'm seeing , any help would greatly be appreciated, Thanks Mark [cid:image002.png@01CEF74F.A95B40D0] _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

2 1

New install no graphs
by Vmman 12 Dec '13

12 Dec '13

I'm a beginner, installed observium on Centos 6.5 64bit, I am able to see my device but no graphs. This is what i'm seeing , any help would greatly be appreciated, Thanks Mark [image: Inline image 1]

2 3

Re: [Observium] observium Digest, Vol 41, Issue 32
by Rutger Bevaart 12 Dec '13

12 Dec '13

Checking the Juniper docs it seems that there is MIB support in JUNIPER-VPN-MIB… If I snmpwalk 1.3.6.1.4.1.2636.3.26 I do indeed get the pseudowire status from the box… I put it here: http://pastebin.com/mMuhdKbA 123456789 is the sanitized pseudo wire ID… Not having looked at the Cisco MIB for this, is it remotely similar making this a doable adventure? Regards, Rutger On 12 Dec 2013, at 05:55, observium-request(a)observium.org wrote: > The pseudowire support was written for Cisco specific MIBs. > > I've no idea if Juniper supply comparable MIBs, but it certainly > wouldn't be compatible without writing code (and partially rewriting the > existing cisco code to be more generic). > > Thanks, > adam. > > On 2013-12-11 20:39, Rutger Bevaart wrote: >> Just setup a hybrid Cisco to Juniper pseudo wire. It is detected by >> Observium just fine on the Cisco side, but not on the Juniper side >> showing a half circuit. >> >> Can I somehow get this working without reverting to a Cisco-Cisco >> setup? >> >> Regards >> Rutger >> _______________________________________________ >> observium mailing list >> observium(a)observium.org >> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Re: [Observium] Graphs Issue
by Josh Hopper 12 Dec '13

12 Dec '13

Hrm.... I will check this in the AM and update. I thought I installed this to the letter.... Thanks. Sam Gu <sam.gu(a)92cloud.com> wrote: We had similar issue before and finally resolved. Please check your cron and rrd folder permission. Please note that the you cannot use cron -e to add task. �� 2013��12��12��ģ�Josh Hopper д�� Hello Observium Members, I have a slight issue with my graphs. I��ve installed the free version of Observium and can log into the web interface easily. When I add a device to Observium using the CLI it has no issue adding the device. However, when I run a ./poller.php �Ch all it says that there is no rrd directory. All the graphs have a ��Data Error�� on them. So, I create the rrd folder and run again. Then data populates. However, it doesn��t list any graphics for the graphs. The graph is present without issue but there is no traffic. It is all of them (System, Netstats and Poller). -- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image003.jpg@01CEF682.B22BCF40] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160 | Cell: 828-855-7565

2 2

FW: Graphs Issue
by Josh Hopper 12 Dec '13

12 Dec '13

Hello Observium Members, I have a slight issue with my graphs. I've installed the free version of Observium and can log into the web interface easily. When I add a device to Observium using the CLI it has no issue adding the device. However, when I run a ./poller.php -h all it says that there is no rrd directory. All the graphs have a "Data Error" on them. So, I create the rrd folder and run again. Then data populates. However, it doesn't list any graphics for the graphs. The graph is present without issue but there is no traffic. It is all of them (System, Netstats and Poller). -- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image003.jpg@01CEF682.B22BCF40] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160 | Cell: 828-855-7565

3 2

Pseudowire Cisco-Juniper monitoring
by Rutger Bevaart 12 Dec '13

12 Dec '13

Just setup a hybrid Cisco to Juniper pseudo wire. It is detected by Observium just fine on the Cisco side, but not on the Juniper side showing a half circuit. Can I somehow get this working without reverting to a Cisco-Cisco setup? Regards Rutger

2 1

observium NGINX report
by Fakrul Alam 12 Dec '13

12 Dec '13

I am trying to pulling nginx nginx_status from observium. But when I run the nginx script I got the following error: ./nginx <<<nginx>>> Traceback (most recent call last): File "./nginx", line 35, in <module> Active = int(params["Reading"]) + int(params["Writing"]) + int(params["Waiting"]) KeyError: 'Reading' Observium is not generating any graph for NGINX. Other SNMP query on that server is ok and I can view all report. Thanks Fakrul

2 2

Graphs Issue
by Josh Hopper 11 Dec '13

11 Dec '13

Hello Observium Members, I have a slight issue with my graphs. I've installed the free version of Observium and can log into the web interface easily. When I add a device to Observium using the CLI it has no issue adding the device. However, when I run a ./poller.php -h all it says that there is no rrd directory. All the graphs have a "Data Error" on them. So, I create the rrd folder and run again. Then data populates. However, it doesn't list any graphics for the graphs. The graph is present without issue but there is no traffic. It is all of them (System, Netstats and Poller). [cid:image001.png@01CEF682.B22BCF40] [cid:image002.png@01CEF682.B22BCF40] -- Sincerely, Joshua Hopper, A+ CE Network Administrator [cid:image003.jpg@01CEF682.B22BCF40] 420 3rd Ave NW Hickory NC 28601 Office: 828-449-1839x2160 | Cell: 828-855-7565

1 0