- observium - lists.observium.org

Fwd: Custom Email Alerts
by consultancy＠lenstewart.com 28 Oct '15

28 Oct '15

Begin forwarded message: > From: "consultancy(a)lenstewart.com" <consultancy(a)lenstewart.com> > Date: 28 October 2015 at 15:55:57 GMT+1 > To: observium(a)observium.net > Subject: Custom Email Alerts > > Hello community. > > I am looking to customize the email alerts to contain specific detail that are not there by default. > > Specifically regarding BGP alerting, I need the system to push out additional peer info such as a peer name (not only an IP). Is there a way to support this either directly or via a script with a lookup? > > Thanks.

1 0

Observium Alert to Nagios
by consultancy＠lenstewart.com 28 Oct '15

28 Oct '15

Hello Community. Can alerts be somehow integrated with Nagios? Either by SNMP or script? Our NOCs primary interface is Nagios/CheckMK. Thanks.

1 0

Flush process causing slow performace
by Johnson, Edward A. 27 Oct '15

27 Oct '15

Since upgrading PHP to 5.4, Observium has loaded very slowly at times. Most of the time just a refresh of the homepage will take .150 seconds but occasionally it can take up to a minute to load. Running iotop shows the Flush process running taking up 99.99% IO which directly correlates to the slow page loads. Can anyone shed some light on a way to resolve this?

3 7

Log Names of non discoverable Host in autodiscover
by Serge Müller 26 Oct '15

26 Oct '15

Hi, is there any way to find out which host have been found through autodiscovery but could not be queried by snmp or aren't reachable via ICMP? Since we have lots of people working on our network, i do not always know if someone plugs in new switches or routers, especially not if they forget to configure the acls or snmp. The Observium log only shows "added x Hosts to ..." but no failures, running discovery.php -d -h all is a bit too loud and takes quite to long. Any suggestions? regards Serge

2 1

SNMP extensions : distro ... and others ?
by Massimo.Sala＠asl.bergamo.it 24 Oct '15

24 Oct '15

hi ! On the linux guests, you can tweak the snmpd.conf as extend .1.3.6.1.4.1.2021.7890.1 distro "/bin/cat /etc/debian_version" so Observium detects the host OS. Is it possible to set other "devices" values, like purpose and serial, via SNMP extensions ? It seems these columns aren't used. best regards, Sala

2 1

BGP Alert Checks
by Aaron Hite 23 Oct '15

23 Oct '15

Team, I need some guidance. I have spent some time on the web trying to find examples of how to configure a alert checker to tell me when a BGP peer is Admin up but not working. We have quite a few peers in our environment that are Admin down and I just want to ignore those. I have tried many variations of the checker, but must be missing something. Here is a screenshot of the latest attempt. My device and entity match are set to “*”. If I change the condition or any instead of all, I seem to get alerts that are not correct as they are including peer states that are admin down. Any guidance would be appreciated. Thanks, Aaron

3 6

simple api to check for hostname / IP address / SOLVED
by Massimo.Sala＠asl.bergamo.it 23 Oct '15

23 Oct '15

I solved with this hack : wget http://servername/graph.php?height=102&width=226&type=device_ping&legend=no… in config.php : enable access to images best regards, Sala --- Is it possible with some URL-fu or simple REST API to check if a hostname and / or IP is in Observium ? The goal is to put this check inside some bash scripts. best regards, Sala

2 1

win srv in VM not listed as srv ( rename device, it disappears from "Servers" view )
by Massimo.Sala＠asl.bergamo.it 23 Oct '15

23 Oct '15

Hi I have a Windows 2003 server, virtual, not listed under "Servers" view. We have many Windows 2003 servers, most of all as guests under Vmware ESX. One of this is listed only in the "All devices" view. To the developers : please, can you give me any insight : how does Observium decide the kind of device ? What I have to check to pinpoint the problem ? Best regards, Sala

2 2

WMI
by Ryan Bones 22 Oct '15

22 Oct '15

Hi All, Trying to monitor some simple Windows Server services (Exchange, SQL). Followed the instructions here to no avail: http://jira.observium.org/secure/attachment/11319/WMIPoller-011013-1429-4.p… When I compile the package wmic never goes in the bin directory. And if I poll the servers I get no new info. Observium 0.15.10.7107 (17th October 2015) OS Linux 3.19.0-25-generic [amd64] (Ubuntu 14.04) Apache 2.4.7 (Ubuntu) PHP 5.5.9-1ubuntu4.12 Python 2.7.6 MySQL 5.5.44-0ubuntu0.14.04.1 (extension: mysqli 5.5.44) SNMP NET-SNMP 5.7.2 RRDtool 1.4.7 Thanks, Ryan Ryan Bones | [http://www.taittowers.com/logo/TAIT_Global_Logo.gif] Network Manager T | +1 717-626-9571 M | +1 717-368-7782 www.taittowers.com<http://www.taittowers.com/>

2 1

Junos Pseudowires
by Σταύρος Κρουστούρης 22 Oct '15

22 Oct '15

Hello, We (GRNET) have created a patch for observium in order to get the pseudowires to work in junos devices. How could I merge it to upstream (in case you want it of course)? -- ----------------------------------------------------------------------- Stavros Kroustouris - staurosk(a)noc.grnet.gr GRNET NOC WEB APPLICATION DEVELOPER - http://noc.grnet.gr -----------------------------------------------------------------------

2 1

simple api to check for hostname / IP address
by Massimo.Sala＠asl.bergamo.it 22 Oct '15

22 Oct '15

Hi Is it possible with some URL-fu or simple REST API to check if a hostname and / or IP is in Observium ? The goal is to put this check inside some bash scripts. best regards, Sala

1 0

view all interfaces listed by IP addresses
by Massimo.Sala＠asl.bergamo.it 22 Oct '15

22 Oct '15

Hi Is it possible to view all devices, listed by their interfaces' IP addresses ? It will be very useful to look-up, at a glance, where a IP address is : just click on it to open its device parent. best regards, Massimo

1 0

RRD Error: Error Drawing Graph
by Greg Lipschitz 22 Oct '15

22 Oct '15

Hi All, We've gone to add in some devices today and they are collecting and polling fine, just getting the error "Error Drawing Graph" Looking at the RRD Output it gives this debug; RRDTool Output: ERROR: String ends after the = sign on 'CDEF:inB=' Here is the command; rrdtool graph /tmp/nW5egDfAQJQJzjxw.png -g --alt-autoscale --rigid --start 1445423655 --end 1445510055 --width 1159 --height 300 -c BACK#EEEEEE00 -c SHADEA#EEEEEE00 -c SHADEB#EEEEEE00 -c FONT#000000 -c CANVAS#FFFFFF00 -c GRID#a5a5a5 -c MGRID#FF9999 -c FRAME#5e5e5e -c ARROW#5e5e5e -R normal --font LEGEND:8:'DroidSansMono,DejaVuSansMono' --font AXIS:7:'DroidSansMono,DejaVuSansMono' --font-render-mode normal -E CDEF:inB= CDEF:outB= CDEF:octets=inB,outB,+ CDEF:doutB=outB,-1,* CDEF:inbits=inB,8,* CDEF:outbits=outB,8,* CDEF:bits=inbits,outbits,+ CDEF:doutbits=doutB,8,* VDEF:95thin=inbits,95,PERCENT VDEF:95thout=outbits,95,PERCENT VDEF:d95thout=doutbits,5,PERCENT VDEF:totin=inB,TOTAL VDEF:avein=inbits,AVERAGE VDEF:totout=outB,TOTAL VDEF:aveout=outbits,AVERAGE VDEF:tot=octets,TOTAL COMMENT:' \l' HRULE:999999999999999#FFFFFF:'Total Rx' GPRINT:inbits:LAST:%6.2lf%s GPRINT:inbits:AVERAGE:%6.2lf%s GPRINT:inbits:MIN:%6.2lf%s GPRINT:inbits:MAX:%6.2lf%s GPRINT:totin:%6.2lf%sB COMMENT:'\l' HRULE:999999999999999#FFFFFF:' Tx' GPRINT:outbits:LAST:%6.2lf%s GPRINT:outbits:AVERAGE:%6.2lf%s GPRINT:outbits:MIN:%6.2lf%s GPRINT:outbits:MAX:%6.2lf%s GPRINT:totout:%6.2lf%sB COMMENT:'\l' HRULE:999999999999999#FFFFFF:' Agg' GPRINT:bits:LAST:%6.2lf%s GPRINT:bits:AVERAGE:%6.2lf%s GPRINT:bits:MIN:%6.2lf%s GPRINT:bits:MAX:%6.2lf%s GPRINT:tot:%6.2lf%sB COMMENT:'\l' HRULE:0#999999 Currently on build 0.15.7.6706 Cheers, Greg Greg Lipschitz | Director | The Summit Group E: Greg(a)thesummitgroup.com.au<mailto:Greg@thesummitgroup.com.au> | W: www.thesummitgroup.com.au<http://www.thesummitgroup.com.au> The Summit Group (Australia) Pty Ltd | P: 1300 049 749 | Level 1, 39 Railway Road, Blackburn VIC 3130 The Summit Group (USA) LLC | P: 321 216 3844 | Suite 1003, 364E Main Street, Middletown DE 19709 Postal: P.O. Box 3225, Doncaster East VIC 3109 Follow us on Facebook<http://www.facebook.com/thesummitgroup/> | LinkedIn<http://www.linkedin.com/company/1942329> | Twitter<http://twitter.com/summitgroupau/>

1 0

Feature request + issues with NetApp cDot and EMC Isilon
by Jesper Frank Nemholt 22 Oct '15

22 Oct '15

Hi Not sure if there is a better place for feature requests, but here it goes : 1. In the group option it would be great to be able to create subgroups and assign/re-assign, so different measures related to the same infrastructure or area can be kept together. 2. Currently it is not possible to rename a group. Would be nice to have this option. 3. Would be great to have some simple functions / regex related to the group graphs to allow consolidating & filtering the data further. Right now it will either aggregate/stack data depending on what it is and it would be more flexible to have some control over this. Also being able to give the aggregated data some more meaningful data labels would be nice. Some time back I asked about NetApp cDOT support....got no answer but saw on the forum that someone was looking into this several months back. Right now the cDOT support is very limited as the MIB is different compared to standard OnTAP and it allow for multiple controller pairs in the same cluster. Any news on what the status is ? Same story for Isilon, here all the server data is gathered, but with complete unawareness of the nodes being in a cluster.... so the only way to get cluster data properly recorded & presented is to create a group for all nodes and create aggregated graphs. Anyone using Observium with IBM GPFS (ESS) ? /Jesper

1 0

Re: [Observium] BGP Alert Checks
by Moerman, Maarten 21 Oct '15

21 Oct '15

https://github.com/mgmoerman/docs/blob/master/observium-alert-checkers.md There's a BGP example there. This works on both Juniper & Cisco with Ipv4 & IPv6 (there's some details on this, in a thread on this mailing list) Maarten -- Maarten Moerman | Mgr, Network Engineering | eBay Classifieds | +31-655122247 | mmoerman(a)ebay.com From: observium on behalf of Aaron Hite Reply-To: Observium Network Observation System Date: Wednesday, October 21, 2015 at 4:32 PM To: "observium(a)observium.org<mailto:observium@observium.org>" Subject: [Observium] BGP Alert Checks Team, I need some guidance. I have spent some time on the web trying to find examples of how to configure a alert checker to tell me when a BGP peer is Admin up but not working. We have quite a few peers in our environment that are Admin down and I just want to ignore those. I have tried many variations of the checker, but must be missing something. Here is a screenshot of the latest attempt. My device and entity match are set to “*”. If I change the condition or any instead of all, I seem to get alerts that are not correct as they are including peer states that are admin down. Any guidance would be appreciated. Thanks, Aaron

2 1

FW: Correct metrics for storage_free checker
by Hilco de Lathouder 21 Oct '15

21 Oct '15

Hi, I'd like to use the storage_free (instead of storage_perc) to get an alert if disk space is below 500 MB. What kind of units are used (byts/mb/kb/gb) ? I was thinking the rule would be like 'storage_free lt 500' if it's in megabytes. Or should i use 'gb' or 'mb' in the equation? Regards, Hilco

2 1

Observium CE / rename device, it disappears from "Servers" view
by Massimo.Sala＠asl.bergamo.it 21 Oct '15

21 Oct '15

Hi Command used : /opt/observium/rename_device.php azimuth3 srvbggwer004 Host azimuth3 renamed to srvbggwer004 I see the server under Devices | All devices, but it disappears from "Servers". Also naming back to "azimuth3" doesn't solve. Is there a database hack to place the host in the right category ? Observium CE 0.15.6.6430 best regards, Sala

1 0

Request: Add a device proactively
by Nate Mellendorf 20 Oct '15

20 Oct '15

Observium team, I just finished pre-deploying a few routers for a new client, and I'm adding each one to our monitoring platforms in advance. As they're offline, I'll be unable to add them to Observium until they respond to SNMP / ICMP. Is there a way I could add these proactively, and work around the error that Observium pushes our by default? Ideally, I'd like to add them all now, disable their alerts, and enable them when they're deployed and connectivity is in place. I see you have a Ignore RRD checkbox on the add device page. I wonder if we could have another that says, "Add even though device is offline"? As always, thank you for your feedback and time on this. Regards, Nate Mellendorf | Network Analyst | Netgain 720 West Saint Germain Street | St. Cloud | MN | 56301 Phone: 320.251.4700 x183 | 877.797.4700 x183 <http://www.netgainhosting.com/> www.NetgainHosting.com _____ The information contained in this email message is for the designated recipient only and may be privileged, confidential, and protected from disclosure. If you have received this message in error, please notify the sender immediately and delete the original. Any dissemination, distribution, copying or other use of this message or any information contained within is strictly prohibited.

7 8

Asterisk DAHDI monitoring
by Pieter De Wit 19 Oct '15

19 Oct '15

Hi Guys, Can we please add DAHDI monitoring to the asterisk agent ? As per http://jira.observium.org/browse/OBSERVIUM-655?focusedCommentId=12588&page=… [1] I will gladly supply a patch to the agent file, if someone can "extend" the view of Asterisk to include dahdichannels and dahdiactive Thanks, Pieter Links: ------ [1] http://jira.observium.org/browse/OBSERVIUM-655?focusedCommentId=12588&p…

1 0

Alert on missing CDP/LLDP neighbor
by Spencer Ryan 19 Oct '15

19 Oct '15

Is is possible to alert on a specific CDP/LLDP neighbor going away? *Spencer Ryan* | Senior Systems Administrator | sryan(a)arbor.net *Arbor Networks* +1.734.794.5033 (d) | +1.734.846.2053 (m) www.arbornetworks.com

1 0

Re: [Observium] Request: Add a device proactively
by Nate Mellendorf 19 Oct '15

19 Oct '15

I was going to do something simular, but thought I'd request a feature add. When I deploy my devices, I deploy them with a script that's been standardized / approved. Setting up DHCP would be possible, but it adds additional steps (prone to user error) and may not be possible for all Observium users. I can see why you may not want to add it, but I feel it would be a really nice time saver for future deployments. You configured Observium to say no, I wont poll you if I can't find you. I think this is a little bit of a grey area, where we know it'll be there eventually. Just my two cents. Thanks again Adam for the consideration. ---------------------------------------------------------------------- Message: 1 Date: Mon, 19 Oct 2015 08:27:26 -0700 From: Robbie Wright <robbie(a)siuslawbroadband.com> To: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] Request: Add a device proactively Message-ID: <CADTKZWZ8kbo7ZU8KAnbANzvh+udkEAaC9Bg05zm+V2AxqZZYmg(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" The way we currently handle this, since all of the devices require dns, is to pre-provision the device on a dhcp network and set dns to the temporary dhcp address. We can do the full config on the on the device, ship it, and when it is in its new location (or while it is being shipped) update dns to the new static IP you pre-provisioned and then when it is plugged in, all should be good with the world. In theory. Most of the time. Robbie Wright Siuslaw Broadband <https://siuslawbroadband.com> 541-902-5101 On Mon, Oct 19, 2015 at 8:14 AM, Matt Ladewig <matt(a)univoip.com> wrote: > I?m in favor of having an offline device add option. We would be able > to add the device to Observium as part of the normal provisioning > workflow, instead of post activation. > > > > *From:* observium [mailto:observium-bounces@observium.org] *On Behalf > Of *Adam Armstrong > *Sent:* Monday, October 19, 2015 8:10 AM > *To:* observium(a)observium.org > *Subject:* Re: [Observium] Request: Add a device proactively > > > > Hmm... I'm not sure about this. What do other people think? > > > > adam. > > On 19/10/2015 16:07:40, Nate Mellendorf < > nate.mellendorf(a)netgainhosting.com> wrote: > > Observium team, > > > > I just finished pre-deploying a few routers for a new client, and I?m > adding each one to our monitoring platforms in advance. > > As they?re offline, I?ll be unable to add them to Observium until they > respond to SNMP / ICMP. > > > > Is there a way I could add these proactively, and work around the > error that Observium pushes our by default? > > Ideally, I?d like to add them all now, disable their alerts, and > enable them when they?re deployed and connectivity is in place. > > > > I see you have a Ignore RRD checkbox on the add device page. I wonder > if we could have another that says, ?Add even though device is offline?? > > > > As always, thank you for your feedback and time on this. > > > > > > Regards, > > > > *Nate Mellendorf **|* *Network Analyst **|* *Netgain* > 720 West Saint Germain Street | St. Cloud | MN | 56301 > Phone: 320.251.4700 x183 *|* 877.797.4700 x183 > *www.NetgainHosting.com* <http://www.netgainhosting.com/> > > > ------------------------------ > > The information contained in this email message is for the designated > recipient only and may be privileged, confidential, and protected from > disclosure. If you have received this message in error, please notify > the sender immediately and delete the original. Any dissemination, > distribution, copying or other use of this message or any information > contained within is strictly prohibited. > > > > > _______________________________________________ > observium mailing list > observium(a)observium.org > http://postman.memetic.org/cgi-bin/mailman/listinfo/observium > >

1 0

Observium CE, housekeeping.php parameters
by Massimo.Sala＠asl.bergamo.it 19 Oct '15

19 Oct '15

Hi ! Reading http://www.observium.org/docs/housekeeping/ -b Cleans up stale entries in the database. Sometimes entries get left behind when devices are removed, this will clean them up. It seems the switch is missing : /opt/observium/housekeeping.php Observium CE 0.15.6.6430 HouseKeeping USAGE: housekeeping.php [-Vyaserptd] [-A <age>] I don't know if the web page is outdated, or I have to update our installation. Please help ! best regards, Sala

2 1

Re: [Observium] Request: Add a device proactively
by Massimo.Sala＠asl.bergamo.it 19 Oct '15

19 Oct '15

Also for me it is useful to add a device even if "dead". If you prefer, add a switch to add_device.php --no-snmp don't check device online So only the wise guys will force it. best regards, Massimo

1 0

Re: [Observium] observium Digest, Vol 63, Issue 65
by Dudu Handelman 19 Oct '15

19 Oct '15

I think it's a solid idea. With other systems i made it in the past. its very useful while you are building a new rack you know that all is up at the end or even during the install. Sent from my Samsung device -------- Original message -------- From: observium-request(a)observium.org Date: 19/10/2015 18:15 (GMT+02:00) To: observium(a)observium.org Subject: observium Digest, Vol 63, Issue 65 Send observium mailing list submissions to observium(a)observium.org To subscribe or unsubscribe via the World Wide Web, visit http://postman.memetic.org/cgi-bin/mailman/listinfo/observium or, via email, send a message with subject or body 'help' to observium-request(a)observium.org You can reach the person managing the list at observium-owner(a)observium.org When replying, please edit your Subject line so it is more specific than "Re: Contents of observium digest..." Today's Topics: 1. Re: Request: Add a device proactively (Adam Armstrong) 2. Re: Request: Add a device proactively (Matt Ladewig) ---------------------------------------------------------------------- Message: 1 Date: Mon, 19 Oct 2015 16:09:45 +0100 From: "Adam Armstrong" <adama(a)memetic.org> To: "" <observium(a)observium.org> Subject: Re: [Observium] Request: Add a device proactively Message-ID: <ba9da84a-386c-4c21-86a7-fdc71ba98e44(a)getmailbird.com> Content-Type: text/plain; charset="utf-8" Hmm... I'm not sure about this. What do other people think? adam. On 19/10/2015 16:07:40, Nate Mellendorf <nate.mellendorf(a)netgainhosting.com> wrote: Observium team, ? I just finished pre-deploying a few routers for a new client, and I?m adding each one to our monitoring platforms in advance. As they?re offline, I?ll be unable to add them to Observium until they respond to SNMP / ICMP. ? Is there a way I could add these proactively, and work around the error that Observium pushes our by default? Ideally, I?d like to add them all now, disable their alerts, and enable them when they?re deployed and connectivity is in place. ? I see you have a Ignore RRD checkbox on the add device page. I wonder if we could have another that says, ?Add even though device is offline?? ? As always, thank you for your feedback and time on this. ? ? Regards, ? Nate Mellendorf | Network Analyst | Netgain 720 West Saint Germain Street | St. Cloud | MN | 56301 Phone: 320.251.4700 x183 | 877.797.4700 x183 www.NetgainHosting.com [http://www.netgainhosting.com/] The information contained in this email message is for the designated recipient only and may be privileged, confidential, and protected from disclosure.? If you have received this message in error, please notify the sender immediately and delete the original.? Any dissemination, distribution, copying or other use of this message or any information contained within is strictly prohibited.?????????????? ?

1 0

DB Errors
by Eduardo Schoedler 19 Oct '15

19 Oct '15

Hi, I have upgraded now to 6655 and I saw an db error. Updated to revision 6655. Observium 0.15.7.6655 Discovery -- Updating database/file schema 203 -> 204 ... (db) done (1 errors). -- Done Looking the logs/db.log file: [2015/07/09 21:46:19 -0300] poller.php(1595): Failed dbQuery (#1062 - Duplicate entry '73-4006-001exxxxxxxx' for key 'dev_vlan_mac'), Query: INSERT INTO `vlans_fdb` (`device_id`,`vlan_id`,`port_id`,`mac_address`,`fdb_status`) VALUES ('73','4006','17112','001exxxxxxxx','learned') [2015/07/09 21:46:19 -0300] poller.php(1595): Failed dbQuery (#1062 - Duplicate entry '73-4006-0022yyyyyyd3' for key 'dev_vlan_mac'), Query: INSERT INTO `vlans_fdb` (`device_id`,`vlan_id`,`port_id`,`mac_address`,`fdb_status`) VALUES ('73','4006','17112','0022yyyyyyd3','learned') ... [2015/07/15 11:49:52 -0300] discovery.php(12686): Failed dbQuery (#1071 - Specified key was too long; max key length is 1000 bytes), Query: ALTER TABLE `slas` DROP INDEX `unique_key`, ADD UNIQUE `unique_key` (`device_id`, `sla_mib`, `sla_index`, `sla_owner`); Can you verify, please? Thanks. -- Eduardo Schoedler

2 6

Cannot see ospf or bgp related graphs on Nexus 9000 and MX 480
by George Philip 19 Oct '15

19 Oct '15

Hi,I have installed Observium and have ospf and bgp related polling ,discovery parameters in the config.php file. However, I am unable to see the routing protocol related graph in the web page. Is there anything else that I need to do as I have these protocols running on the Nexus 9000 and MX480 router. Thanks,George

1 0

Juniper QFX 10G ports discovered as 4.29G
by Aaron Finney 18 Oct '15

18 Oct '15

Just FYI, the 10G ports on a QFX 5100 running latest JunOS are being reported with a speed of 4.29Gbps, which I assume is likely the actual returned value being constrained by a 32-bit container? Not a critical thing for us to fix - I was actually disabling polling for all of our Juniper vcp stacks in Observium (most of them take > 300s to complete a polling cycle) but noticed this as I was going through them and figured I'd pass it along. Cheers, Aaron

6 9

Re: [Observium] Tripplite PDUMNH20 (power strips)
by Ralph Pursifull 17 Oct '15

17 Oct '15

Great progress. Data now appears in RRD, just it’s off by 10 X. Plots show 1.1, correct answer is 11.0 Amps. When I look at the device with iReasoning MIB browser, using the UPS-MIB supplied by TrippLite, or the UPS-MIB from Observium, it says: integer: 11 See attached. Seems most of the MIB files mention units of “0.1 RMS Amp”. Not sure what that does. Any way to resolve this? upsOutputCurrent OBJECT-TYPE SYNTAX NonNegativeInteger UNITS "0.1 RMS Amp" MAX-ACCESS read-only STATUS current DESCRIPTION "The present output current." ::= { upsOutputEntry 3 } From: Mike Stupalov [mailto:mike@stupalov.ru] Sent: Friday, October 16, 2015 4:23 PM To: Ralph Pursifull <ralph(a)palamida.com> Cc: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) I see that Current output already discovered (with value 1.1): Discover sensor: current, pdu72, .1.3.6.1.2.1.33.1.4.4.1.3.1, upsOutputEntry.1, ups-mib, Output, SCALE: 0.1, LIMITS: (, , , ), CURRENT: 1.1 But I fix (clean) some incorrectly discovered sensors in r7105. On Sat, Oct 17, 2015 at 1:20 AM, Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Here you go. Thanks for your help on this. From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Mike Stupalov Sent: Friday, October 16, 2015 3:07 PM To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) Hi, observium already have mostly support for UPS-MIB including upsOutputCurrent. Seems as something wrong in snmpwalk output. Send me debug output for: ./discovery.php -d -m sensors -h <this_device> On Sat, Oct 17, 2015 at 12:21 AM, Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Hi Adam, Still have a problem with a fresh Professional install of “current” observium/trunk. Situation: For a Tripplite PDUMNH20 (power strip) we want to display total current. This will help us manage power consumption in our remote rack at the colo site, where we pay directly for amps. Latest “current” Observium page generated for PDUMNH20 attempts to display a “Current” plot in the upper right. Unfortunately all values are “0” with units of “–nan”. TrippLite Support tells me we want this data item from the UPS-MIB. Name: upsOutputCurrent.1 OID: .1.3.6.1.2.1.33.1.4.4.1.3.1 Data : 4 Descroption: The present output current. Please can you plot that one? What OID are you trying to plot? What is cost of fix? Happy to go that route. Ralph From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Adam Armstrong Sent: Thursday, October 08, 2015 1:04 PM To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) Hi Ralph, Its possible this is already fixed in the current subscription edition. If not, you have two options (both of which require having a subscription!): Hope we fix it once you confirm its not fixed in subscription. Pay someone for a couple of hours work to fix it. The choice between the two is usually based on how much you want the fix :) I vaguely recall some triplite stuff changing in the recent past, so chances are it's fixed already. I don't have any of those devices though, so can't say for certain with looking into it a little further. Adam. Sent with AquaMail for Android http://www.aqua-mail.com On 8 October 2015 8:37:53 pm Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Hi. New to this list, so please excuse if I break etiquette. For couple years we happily used Observium to monitor and track current through our Tripplite PDUMNH20. Thanks to you all for Observium. Life was OK, but the integrated Tripplite SNMPWEBCARDs had problems from time to time. Tripplite rolled out new firmware (currently 12.06.0065) and that issue was resolved. (SNMPWEBCARD is a component used in many of their products.) Unfortunately, now current plots as a flat line at 0. I’ve worked with Tripplite support to verify some data is present with snmpwalk. But probably not where Observium expects to find it. My guess is the firmware change switched to a new mib. I’ve tried to delete devices, update Observium and recreate… no luck. Tripplite currently provides these two MIBs http://www.tripplite.com/shared/software/Firmware/UPS-MIB-Definitions.txt http://www.tripplite.com/shared/software/Firmware/Tripp-Lite-MIB-Definition… Would be happy to switch to Professional, buy support, whatever is needed to restore ability to plot Current over time from Tripplite PDUMNH20. Any good advice? _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium%40observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium<http://postman.memetic.org/cgi-bin/mailman/listinfo/observium> _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium -- Mike Stupalov http://observium.org/

2 1

Tripplite PDUMNH20 (power strips)
by Ralph Pursifull 16 Oct '15

16 Oct '15

Hi. New to this list, so please excuse if I break etiquette. For couple years we happily used Observium to monitor and track current through our Tripplite PDUMNH20. Thanks to you all for Observium. Life was OK, but the integrated Tripplite SNMPWEBCARDs had problems from time to time. Tripplite rolled out new firmware (currently 12.06.0065) and that issue was resolved. (SNMPWEBCARD is a component used in many of their products.) Unfortunately, now current plots as a flat line at 0. I've worked with Tripplite support to verify some data is present with snmpwalk. But probably not where Observium expects to find it. My guess is the firmware change switched to a new mib. I've tried to delete devices, update Observium and recreate... no luck. Tripplite currently provides these two MIBs http://www.tripplite.com/shared/software/Firmware/UPS-MIB-Definitions.txt http://www.tripplite.com/shared/software/Firmware/Tripp-Lite-MIB-Definition… Would be happy to switch to Professional, buy support, whatever is needed to restore ability to plot Current over time from Tripplite PDUMNH20. Any good advice?

3 4

Add Bill to Normal User & Password Change for normal User
by Basile Bluntschli 16 Oct '15

16 Oct '15

Hi All 1) I no longer can add a bill to a normal user. While the dropdown menu is there, I can select the bill, but it does not get saved by clicking on ADD. 2) Where is a normal User able to change its password? URL? Running 7097 Thanks a lot Basile

3 3

Escaped sysContact not being escaped properly
by Spencer Ryan 16 Oct '15

16 Oct '15

I've got several UBNT devices all running EdgeMax 1.7.0 It appears that they escape the sysContact (and a few other fields) in quotes even if they don't have spaces in them. Observium seems to eat the first one properly but not the second. snmpwalk -Os -c public -v 2c router01 1.3.6.1.2.1.1.4 iso.3.6.1.2.1.1.4.0 = STRING: "\"hostmaster(a)arbor.net\"" However in the UI I see this: sysContact*=>*hostmaster(a)arbor.net\ Which causes email notifications to fail, because of the bad email address. Any hope? *Spencer Ryan* | Senior Systems Administrator | sryan(a)arbor.net *Arbor Networks* +1.734.794.5033 (d) | +1.734.846.2053 (m) www.arbornetworks.com

2 2

Ignore Statuses Possible?
by Tim Calvin 15 Oct '15

15 Oct '15

Hello We have a few AC powered Foundry FWS-24 switches. Observium is showing alerts for the secondary power supply and fans under statuses. Is there anyway to ignore these? I tried poking around and couldn’t find anything that would do the trick. I don’t even think they have secondary power supplies and fans. Maybe in another hardware configuration but certainly not ours. I have attached a screenshot. Running Observium Professional 0.15.10.7072

3 2

dlink DGS-1100-24 only found as generic
by Simon Smith 15 Oct '15

15 Oct '15

Hi All, our new D-Link DGS-1100-24 switches are only being discovered as generic device but strangely enough its finding 1 vlan? the syObjectID is being found as .1.3.6.1.4.1.171 but i can see inside os.inc.php the sysObjectID is already included as D-Link-Generic (Line:1950) even tho it could be put under the D-Link Switch (Line:1927) i have included a run poller.php and discover.php commands here - http://pastebin.com/8iKYU16N can the great and wonderful people working at Observium please help :-) Regards Simon - Hestor Ltd

2 3

Re: [Observium] Cannot see ospf or bgp info
by George Philip 15 Oct '15

15 Oct '15

Hi Adam,I am using Nexus 9k's and MX 480 with ospf and bgp. I am not sure why I don't any protocol related information on Observium. Thanks,George From: Adam Armstrong <adama(a)observium.org> To: George Philip <gkonapoz(a)yahoo.com> Sent: Wednesday, October 14, 2015 12:33 PM Subject: Re: [Observium] Cannot see ospf or bgp info Hi George,These features will only becomevisible in the ui once a device which supports them has been discovered andpolled.The devices need to supportbgp4-mib and ospf-mib.Thanks, Adam.Sent with AquaMail for Android http://www.aqua-mail.com On14 October 2015 4:11:30 pm George Philip <gkonapoz(a)yahoo.com> wrote: Hi,I installed Observium and have enabledthe bgp and ospf polling. However, I do not see the option of seeing thatinfo from the gui. I can see graphs on traffic but I cannot see any titlefor ospf or bgp. Also, I do not any entries for arp or mac table. Do I need to have license for thesefeatures ? Thanks, George_______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Cannot see ospf or bgp info
by George Philip 14 Oct '15

14 Oct '15

Hi,I installed Observium and have enabled the bgp and ospf polling. However, I do not see the option of seeing that info from the gui. I can see graphs on traffic but I cannot see any title for ospf or bgp. Also, I do not any entries for arp or mac table. Do I need to have license for these features ? Thanks, George

1 0

Obervium web page not coming up
by George Philip 14 Oct '15

14 Oct '15

Hi,I installed Observium on Centos and I added devices also successfully.Somehow, the webpage is not coming up and I followed the instruction mentioned in the webpage.My file /etc/http/conf/httpd.conf looks as follows: # <VirtualHost> definition. These values also provide defaults for # any <VirtualHost> containers you may define later in the file. # # All of these directives may appear inside <VirtualHost> containers, # in which case these default settings will be overridden for the # virtual host being defined. # # # ServerAdmin: Your address, where problems with the server should be # e-mailed. This address appears on some server-generated pages, such # as error documents. e.g. admin(a)your-domain.com # #ServerAdmin root@localhost # # ServerName gives the name and port that the server uses to identify itself. # This can often be determined automatically, but we recommend you specify # it explicitly to prevent problems during startup. # # If your host doesn't have a registered DNS name, enter its IP address here. # <VirtualHost *:80> DocumentRoot /opt/observium/html/ ServerName asvobs02.abcd.io CustomLog /opt/observium/logs/access_log combined ErrorLog /opt/observium/logs/error_log <Directory "/opt/observium/html/"> AllowOverride All Options FollowSymLinks MultiViews </Directory> </VirtualHost> Thanks, George

3 6

Service monitoring feature
by Stephen Penfold 14 Oct '15

14 Oct '15

Hi Guys, I know service monitoring (nagios plug-in) is now deprecated and removed however just curious if there will be any chance of the feature being developed in future? Would be nice to do away with Nagios and have Observium as our all-in-one monitoring solution ☺ Cheers Stephen Penfold Helpdesk Support Assistant Tel: +61 7 5553 5995 Email: Stephen.Penfold(a)careflight.org.au Web: www.careflight.org.au Address: PO Box 5078, Robina, QLD, 4230 [cid:imagec15b3f.JPG@2e3eebe0.45828f54] <http://www.careflight.org.au> [cid:image91d517.PNG@d77d9f73.42982d3b]<https://www.facebook.com/RACQCareFlight> [cid:imaged92729.PNG@c049b465.42a799e2] <https://twitter.com/CareFlightQLD> [cid:image0c3b01.PNG@d1cb199d.4586a257] <https://instagram.com/racqcareflightrescue/> [cid:image7cbb03.PNG@733799ae.4b9641ad] <https://www.youtube.com/user/careflightgroup> [cid:image86e2db.PNG@642ee964.48aeeeac] <https://www.linkedin.com/company/careflight-group-queensland> [cid:image110385.PNG@c4d861a6.498f72f2]<http://newsletter.brightlabs.com.au/h/r/4FBDC674FBFB389D> This communication including any file attachments is intended solely for the use of the individual or entity to whom it is addressed. If you are not the intended recipient, or the person responsible for delivering this communication to the intended recipient, please immediately notify the sender by email and delete the original transmission and its contents. Any unauthorised use, dissemination, forwarding, printing, or copying of this communication including any file attachments is prohibited. It is your responsibility to scan this communication including any file attachment for viruses and other defects. To the extent permitted by law, CareFlight Group and its associates will not be liable for any loss or damage arising in any way from this communication including file attachments.

1 0

Switch uptime
by Eduardo Schoedler 14 Oct '15

14 Oct '15

Hi, Is there a problem with switches uptime? [image: Imagem inline 2] # /usr/bin/snmpget -v2c -c 'xxxxxxxx' -Pu -OQUst -m SNMPv2-MIB -M /opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp 'udp':'my-host':'161' sysObjectID.0 sysUpTime.0 sysObjectID.0 = enterprises.4413 sysUpTime.0 = 227811800 # snmpwalk -v 2c -c xxxxxxxx my-host sysUpTime DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (227812500) 26 days, 8:48:45.00 Thank you. -- Eduardo Schoedler

1 0

10gbps port showing as 10bps
by Cameron Murray 12 Oct '15

12 Oct '15

As the subject says we've recently installed a 10gbps Dell switch and the ports are showing as bps not gbps. ALERT Modify<http://cacti.bettacomputers.com.au/device/device=99/tab=alert/alert_entry=5…> Alert Utilization has exceeded 80% Entity tengigabitethernet1/0/1<http://cacti.bettacomputers.com.au/device/device=99/tab=port/port=2260/> Conditions ifInOctets_perc gt 80 (623770) ifOutOctets_perc gt 80 (631740) Metrics ifInOctets_perc = 623770 ifOutOctets_perc = 631740 Duration 3 days, 1h 13m 43s (2015-09-28 13:43:41) Device Device bne-be-l2r16-sw10g<http://cacti.bettacomputers.com.au/device/device=99/> Hardware Operating System Generic Device Location Uptime 3 days, 3h 46m 24s The ports that are trained up as 1gbps show correctly however higher do not. Port Data: port_id => 2260 device_id => 99 port_64bit => 1 port_label => tengigabitethernet1/0/1 port_label_base => null port_label_num => null port_label_short => Te1/0/1 port_descr_type => null port_descr_descr => null port_descr_circuit => null port_descr_speed => null port_descr_notes => null ifDescr => tengigabitethernet1/0/1 ifName => te1/0/1 portName => null ifIndex => 1 ifSpeed => 10 ifConnectorPresent => true ifPromiscuousMode => true ifHighSpeed => 10000 ifOperStatus => up ifAdminStatus => up ifDuplex => fullDuplex ifMtu => 1500 ifType => ethernetCsmacd ifAlias => ifPhysAddress => f8b15686e676 ifHardType => null ifLastChange => 2015-09-28 11:37:54 date-7da Australia/Brisbane (UTC+10) ifVlan => 1 ifTrunk => dot1Q ifVrf => null ignore => 0 disabled => 0 detailed => 0 deleted => 0 pagpOperationMode => null pagpPortState => null pagpPartnerDeviceId => null pagpPartnerLearnMethod => null pagpPartnerIfIndex => null pagpPartnerGroupIfIndex => null pagpPartnerDeviceName => null pagpEthcOperationMode => null pagpDeviceId => null pagpGroupIfIndex => null ifInUcastPkts => 0 ifInUcastPkts_delta => 0 ifInUcastPkts_rate => 0 ifOutUcastPkts => 0 ifOutUcastPkts_delta => 0 ifOutUcastPkts_rate => 0 ifInErrors => 0 ifInErrors_delta => 0 ifInErrors_rate => 0 ifOutErrors => 0 ifOutErrors_delta => 0 ifOutErrors_rate => 0 ifOctets_rate => 199209 ifUcastPkts_rate => 0 ifErrors_rate => 0 ifInOctets => 30302781555 ifInOctets_delta => 46292430 ifInOctets_rate => 152780 ifOutOctets => 15509016948 ifOutOctets_delta => 14067927 ifOutOctets_rate => 46429 ifInOctets_perc => 255 ifOutOctets_perc => 255 poll_time => 1444083140 poll_period => 303 ) Regards, Cameron Murray Remote Support Engineer How am I doing? Please click here<http://www.techpath.com.au/contact-us/feedback/> to rate my work. [cid:image001.png@01D1000F.A5564960]<http://www.techpath.com.au/> P 1300 033 300 F 07 3809 3999 E cameron(a)techpath.com.au www.techpath.com.au<http://www.techpath.com.au> Unit 2/55 Tradelink Rd, Hillcrest QLD 4118 Formerly Betta Computer Services Pty Ltd [Facebook]<http://www.facebook.com/techpathau> [Twitter]<http://twitter.com/techpathau> [LinkedIn]<http://www.linkedin.com/company/techpathau> Note: This message may contain privileged and confidential information that is the property of the intended recipient. The information herein is intended only for use of the addressee. If you are not the intended recipient, then you are requested to return e-mail to TechPath Pty Ltd and destroy any copies made. Copying or disseminating any of this message is prohibited. Any views expressed in this message are those of the individual sender and may not necessarily reflect the views of TechPath Pty Ltd.

6 20

Problem adding user to view a port / vlan
by Stephen Bateman 11 Oct '15

11 Oct '15

Hi Everyone, Is there a procedure for adding a single user who I want to see vlan traffic statistics and the ports on a switch. I have tired creating a normal user which worked fine. However when I select the device and the port and click Add nothing happens. When I click refresh it still says "This user currently has no permitted ports" Any help would be appreciated, I am using the Professional version 0.15.10.7095 Thanks Stephen

1 0

Re: [Observium] email alert showing device_ping
by Gavin Henry 11 Oct '15

11 Oct '15

You might want you have scrubbed that image or fixed your firewall: https <https://proxmox.zeplin.co.uk:8006/#v1:0:18:4::::>:// <https://proxmox.zeplin.co.uk:8006/#v1:0:18:4::::>proxmox.zeplin.co.uk <https://proxmox.zeplin.co.uk:8006/#v1:0:18:4::::>:8006/#v1:0:18:4:::: <https://proxmox.zeplin.co.uk:8006/#v1:0:18:4::::>::

2 1

email alert showing device_ping
by Simon Smith 11 Oct '15

11 Oct '15

Hi All, has anybody noticed the weird alerts being sent by email or is it just myself with this issue? I have an alert setup to tell me if device_uptime is between 0 and 600 then alert me (rebooted kit/server) however the email is showing the words device_ping under the email alerts where a graph would show if the alert had a graph attached a screenshot to show you what i mean regards Simon

1 0

aggregate graphs
by Jeffrey d'Ambly 09 Oct '15

09 Oct '15

Is there way to create aggregate graphs using graph.php? —Jeff

2 4

Orphaned ports
by Aaron Mayfield 09 Oct '15

09 Oct '15

I've been digging around in my database, trying to figure out why I have a large number of ports listed in my observium interface, compared to the number of devices I have. I have discovered several devices that were removed (via delete_device.php) a while back, but it seems that the ports table wasn't completely cleaned up. These devices were removed from the devices table: mysql> select * from devices where device_id in(45,66,67,68,69,70,71,72,73); Empty set (0.00 sec) mysql> But the ports for these devices weren't entirely removed: mysql> select device_id,count(*) as "number of ports" from ports where device_id IN(45,66,67,68,69,70,71,72,73) group by device_id; +-----------+-----------------+ | device_id | number of ports | +-----------+-----------------+ | 45 | 4153 | | 66 | 4153 | | 67 | 4153 | | 68 | 4153 | | 69 | 4153 | | 70 | 1569 | | 71 | 4153 | | 72 | 4153 | | 73 | 4153 | +-----------+-----------------+ 9 rows in set (0.01 sec) mysql> These devices were probably F10/Dell M1000e cards, which I removed from observium because of the large number of l2vlan interfaces on each was causing a processor burden when polled. Rather than fight with them, I just removed them. My question is this, how can I clean up the remnants? Can I just delete these orphaned ports from the table? Or will I break anything if I do that? Thanks This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error, please notify the system manager. Please note that any views or opinions present in this email are solely those of the author and do not necessarily represent those of the company. Finally the recipient should check this email and any attachment for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. (Proprietary & Confidential - Artisan Infrastructure, Inc. et all.)

2 2

DRBD Stats / Agent
by Robert Williams 09 Oct '15

09 Oct '15

Hi, Is anyone successfully using the agent to retrieve DRBD statistics? We may be suffering from http://jira.observium.org/browse/OBSERVIUM-574 - I'm not 100%, but I wondered if anyone had fixed it or found a workaround and simply hadn't shared their findings on Jira? Cheers all! Robert Williams Custodian Data Centre Email: Robert(a)CustodianDC.com http://www.CustodianDC.com

2 2

Multiple OSPF processes
by Miguel Berniz 09 Oct '15

09 Oct '15

Hello, I have noticed only 1 OSPF process is detected on cisco devices. I have a Catalyst 4500 with 3 processes but only one of them is handle by observium. Is this the normal behavior or does it require special config or not supported at all? Thanks in advance, Miguel

2 1

Update http://www.observium.org/docs/add_device/ for missing "search" line with resolv.conf
by Przemysław S. Knycz 08 Oct '15

08 Oct '15

Hello! I've wird problem with "Can't resolve ...." when adding device (from ./add_device.php and from website). Te solution was simple - there was missing "search domain" at /etc/resolv.conf - i don't find this kind of problem and solution, so you can add it at site to Troubleshooting. Thanks. Regards. -- . Przemyslaw Stanislaw Knycz, +48 601391681 . | WiFi&fiber engineer, xmpp:djrzulf@gmail.com | ` Futurama: You can't prove it won't happen '

1 0

Professional Edition
by Jorge Riveiro Fernandez 06 Oct '15

06 Oct '15

Dear Team, ¿Is possible to make Professional Edition payment via bank transfer or something alternative to credit card or Paypal? BR Jorge Riveiro Fernández Votorantim Cimentos Europe, Africa & Asia IT - Telecoms Area Corporate Center Vigo jorge.riveiro(a)vcimentos.com<mailto:jorge.riveiro@vcimentos.com>

1 0

rsyslog omprog integration Problem
by Serge Müller 05 Oct '15

05 Oct '15

Hi, i'm running observium (latst svn) on a ubuntu 14.04 System. Have Setup rsyslog for udp listening, deployed /etc/rsyslog.d/30-observium.conf as stated in http://www.observium.org/docs/syslog/ However my observium.syslog table stays empty. I have enabled debugging and syslog debuging in config.php so everytime i send a string to /opt/observium/syslog.php the string appears in my observium debug logs. I have started rsyslog in debug mode and (from what rsyslog says) it executes syslog.php: 9163.747286922:7f66a9681700: scriptExec: batch of 1 elements, active (nil), active[0]:1 9163.747293145:7f66a9681700: PROPFILT 9163.747311025:7f66a9681700: Property.: 'inputname' 9163.747324703:7f66a9681700: Operation: 'isequal' 9163.747344027:7f66a9681700: Value....: 'imudp' 9163.747359865:7f66a9681700: Filter: check for property 'inputname' (value 'imudp') isequal 'imudp': TRUE 9163.747370811:7f66a9681700: batch: item 0 PROPFILT 1 9163.747376767:7f66a9681700: scriptExec: batch of 1 elements, active 0x7f66980008e0, active[0]:1 9163.747382283:7f66a9681700: ACTION 0x1fb4d40 [omprog::omprog:;observium] 9163.747404416:7f66a9681700: RRRR: execAct [omprog]: batch of 1 elements, active 0x7f66980008e0 9163.747411147:7f66a9681700: Called action(NotAllMark), processing batch[0] via 'omprog' 9163.747416542:7f66a9681700: Called action(Batch), logging to omprog 9163.747428741:7f66a9681700: submitBatch: enter, nElem 1 9163.747437691:7f66a9681700: tryDoAction 0x1fb4d40, pnElem 1, nElem 1 9163.747443729:7f66a9681700: Action 0x1fb4d40 transitioned to state: itx 9163.747449524:7f66a9681700: entering actionCalldoAction(), state: itx 9163.747471965:7f66a9681700: executing program '/opt/observium/syslog.php' 9163.747917480:7f66a9681700: child has pid 27457 9163.747944939:7f66a9681700: Action 0x1fb4d40 transitioned to state: rdy 9163.747956857:7f66a9681700: action 0x1fb4d40 call returned 0 9163.747978533:7f66a9681700: scriptExec: batch of 1 elements, active 0x7f66980008e0, active[0]:1 9163.748003042:7f66a9681700: STOP and it even returns 0 ! anyone ever stumbled upon such a problem? i put in an additional line in 30-observium.conf :inputname, isequal, "imudp" /var/log/remote/debug.log;observium and it logs my messages just fine any ideas would be highly appreciated best regards Serge

1 0

Custom contacts
by Tim Vaughan 02 Oct '15

02 Oct '15

Hi, is it possible to write my own methods for alert contacts? I'd like to add other services, similar to Pushover, which use a JSON API. Is there any documentation I can use to get started? -- Mobile: 07868246225 Skype: tvaughan Twitter: twitter.com/tvaughan

1 0