- observium - lists.observium.org

Graphs with Color Coded Percent Utilization
by Gumilar Siegfried 24 Jun '16

24 Jun '16

Hello, I am currently trying to completely replace our cacti installation with Observium. One of the last things that make me hold on to cacti are these kind of graphs: [cid:image001.gif@01D1C580.2CFF4E30] The graphs are described here: http://forums.cacti.net/viewtopic.php?f=6&t=8520 We have put the most important interfaces on our NOC screen and can immediately recognize if some interfaces are under unusual high load. Is there a way I can achieve something similar with Observium? Thanks, Regards Siegfried

4 6

One of my Apache servers do not show
by Bernard Savonet (M) 24 Jun '16

24 Jun '16

Hi, I've recently added some hosts to my monitored services. - All are running Apache 2.4 so I applied the Apache configuration as described at http://www.observium.org/docs/apps/#apache - All except one show the Apache application info as expected. - Except for the missing Apache info, this site is correctly reported (so general snmp / xinet config are fine) - I have carefully reviewed the different points for this host and Apache config, all is nominal. Which are the points I might have done wrong in the checklist? Which other points not in the checklist should I look at? Thx for your help Bernard

2 1

Alert Checker for memory?
by Dano, Leo 23 Jun '16

23 Jun '16

I created an alert to let me know when a host uses over 90% of its memory. The problem is that linux uses over that in "cached" memory. Is there a way to exclude cached memory? Physical and Swap are fine. I am using mempool_perc greater 90 in Check Conditions. Thanks, ----------------------- Leo Dano

3 6

Alert Checkers and Syslog Rules?
by Dano, Leo 23 Jun '16

23 Jun '16

Hello all, I am able to edit/delete my Alert Checkers but cannot edit or delete my Syslog Rules that I made. Any suggestions? Thanks, ----------------------- Leo Dano

2 8

Can't reset password or get an account activated?
by Dano, Leo 23 Jun '16

23 Jun '16

Hello, Finally bought the subscription version. Except, I get a link to the Subscription Management Portal and none of my passwords work. So I tried to reset but never get an email. I then tried to create a new account using a personal email but it never sends me an activation link. Is there a phone number I can call? Or does my request get on a boat and travel across the Atlantic Ocean? Thanks, ----------------------- Leo Dano

2 4

Support for qLogic FW switches...?
by Henrik Cednert (Filmlance) 23 Jun '16

23 Jun '16

Hi Have anyone played with and added support for qlogic devices in their installation? Have two SANBox 5800 i'd like to monitor. Snmpwalk of one of them: http://pastebin.com/DWRuShaf Cheers -- Henrik Cednert cto | compositor Filmlance International | www.filmlance.se mobile [ + 46 (0)704 71 89 54 ] skype [ cednert ]

1 0

Delay the alert trigger in case of loss only one ping
by prost pierrick 23 Jun '16

23 Jun '16

Hi everyone , Observium lost 1 ping sometime (I don't know why ) after each ping lost, alerts are triggered. Actually I have only two Alerts Checks : Device Down device_status equals 0 * * Device UP device_status equals 1 * * It's possible to add a delay before triggering ? Like waiting 5 ping lost before triggering ? Regards. Pierrick Prost

2 2

CBQoS Aggregation Graph
by David Ron 22 Jun '16

22 Jun '16

Dear All, I remember there was a thread regarding this matter, but I couldn't get into the observium archive to read the whole thread. To make a long story short, I'm looking for a way to aggregate a class-map that is configured on several interfaces on one graphs, like, one graph for Bronze, one graph for Silver and one graph for Gold that summarize the CBQoS graphs for 8 different interfaces. is it possible? David Cellcom Israel Network Engineer

1 0

CAS authentication
by Josep Manel Andrés 21 Jun '16

21 Jun '16

Hi all, I've seen that CAS authentication is already integrated, but I've found no documentation. I've tried to set: vi /opt/observium/config.php // Authentication Model $config['auth_mechanism'] = 'cas'; $config['auth_cas_host'] = 'cas02.domain.es'; $config['auth_cas_port'] = '443'; $config['auth_cas_context'] = 'cas'; $config['auth_cas_ca_cert'] = '/etc/tls/cacert/DigiCertCA'; //$config['auth_mechanism'] = "http-auth"; //$config['http_auth_guest'] = "admin"; but it didn't work, I get "Error: Internal script failure" which comes from phpcas. I've installed the latest version of phpcas from the original source. Thanks. -- Josep Manel Andrés (josep.andres(a)bsc.es) Operations - Barcelona Supercomputing Center C/ Jordi Girona, 31 http://www.bsc.es 08034 Barcelona, Spain Tel: +34-93-405 42 14 e-mail: systems(a)bsc.es Fax: +34-93-413 77 21 ----------------------------------------------- WARNING / LEGAL TEXT: This message is intended only for the use of the individual or entity to which it is addressed and may contain information which is privileged, confidential, proprietary, or exempt from disclosure under applicable law. If you are not the intended recipient or the person responsible for delivering the message to the intended recipient, you are strictly prohibited from disclosing, distributing, copying, or in any way using this message. If you have received this communication in error, please notify the sender and destroy and delete any copies you may have received. http://www.bsc.es/disclaimer

2 2

Netonix Support
by Robbie Wright 21 Jun '16

21 Jun '16

Adam, it looks like you weighed in a little bit with the Netonix guys a year and a half ago about getting support for their switches in. They've got their own enterprise number now and many others are having great success using it. Any thoughts and getting full support in (the paid for version of) Observium? I can get use SNMP access to a test device if you'd like. http://forum.netonix.com/viewtopic.php?p=2072#p2072 Robbie Wright Siuslaw Broadband <https://siuslawbroadband.com> 541-902-5101

1 0