- observium - lists.observium.org

Juniper QFX 10G ports discovered as 4.29G
by Aaron Finney 18 Oct '15

18 Oct '15

Just FYI, the 10G ports on a QFX 5100 running latest JunOS are being reported with a speed of 4.29Gbps, which I assume is likely the actual returned value being constrained by a 32-bit container? Not a critical thing for us to fix - I was actually disabling polling for all of our Juniper vcp stacks in Observium (most of them take > 300s to complete a polling cycle) but noticed this as I was going through them and figured I'd pass it along. Cheers, Aaron

6 9

Re: [Observium] Tripplite PDUMNH20 (power strips)
by Ralph Pursifull 17 Oct '15

17 Oct '15

Great progress. Data now appears in RRD, just it’s off by 10 X. Plots show 1.1, correct answer is 11.0 Amps. When I look at the device with iReasoning MIB browser, using the UPS-MIB supplied by TrippLite, or the UPS-MIB from Observium, it says: integer: 11 See attached. Seems most of the MIB files mention units of “0.1 RMS Amp”. Not sure what that does. Any way to resolve this? upsOutputCurrent OBJECT-TYPE SYNTAX NonNegativeInteger UNITS "0.1 RMS Amp" MAX-ACCESS read-only STATUS current DESCRIPTION "The present output current." ::= { upsOutputEntry 3 } From: Mike Stupalov [mailto:mike@stupalov.ru] Sent: Friday, October 16, 2015 4:23 PM To: Ralph Pursifull <ralph(a)palamida.com> Cc: Observium Network Observation System <observium(a)observium.org> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) I see that Current output already discovered (with value 1.1): Discover sensor: current, pdu72, .1.3.6.1.2.1.33.1.4.4.1.3.1, upsOutputEntry.1, ups-mib, Output, SCALE: 0.1, LIMITS: (, , , ), CURRENT: 1.1 But I fix (clean) some incorrectly discovered sensors in r7105. On Sat, Oct 17, 2015 at 1:20 AM, Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Here you go. Thanks for your help on this. From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Mike Stupalov Sent: Friday, October 16, 2015 3:07 PM To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) Hi, observium already have mostly support for UPS-MIB including upsOutputCurrent. Seems as something wrong in snmpwalk output. Send me debug output for: ./discovery.php -d -m sensors -h <this_device> On Sat, Oct 17, 2015 at 12:21 AM, Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Hi Adam, Still have a problem with a fresh Professional install of “current” observium/trunk. Situation: For a Tripplite PDUMNH20 (power strip) we want to display total current. This will help us manage power consumption in our remote rack at the colo site, where we pay directly for amps. Latest “current” Observium page generated for PDUMNH20 attempts to display a “Current” plot in the upper right. Unfortunately all values are “0” with units of “–nan”. TrippLite Support tells me we want this data item from the UPS-MIB. Name: upsOutputCurrent.1 OID: .1.3.6.1.2.1.33.1.4.4.1.3.1 Data : 4 Descroption: The present output current. Please can you plot that one? What OID are you trying to plot? What is cost of fix? Happy to go that route. Ralph From: observium [mailto:observium-bounces@observium.org<mailto:observium-bounces@observium.org>] On Behalf Of Adam Armstrong Sent: Thursday, October 08, 2015 1:04 PM To: Observium Network Observation System <observium(a)observium.org<mailto:observium@observium.org>> Subject: Re: [Observium] Tripplite PDUMNH20 (power strips) Hi Ralph, Its possible this is already fixed in the current subscription edition. If not, you have two options (both of which require having a subscription!): Hope we fix it once you confirm its not fixed in subscription. Pay someone for a couple of hours work to fix it. The choice between the two is usually based on how much you want the fix :) I vaguely recall some triplite stuff changing in the recent past, so chances are it's fixed already. I don't have any of those devices though, so can't say for certain with looking into it a little further. Adam. Sent with AquaMail for Android http://www.aqua-mail.com On 8 October 2015 8:37:53 pm Ralph Pursifull <ralph(a)palamida.com<mailto:ralph@palamida.com>> wrote: Hi. New to this list, so please excuse if I break etiquette. For couple years we happily used Observium to monitor and track current through our Tripplite PDUMNH20. Thanks to you all for Observium. Life was OK, but the integrated Tripplite SNMPWEBCARDs had problems from time to time. Tripplite rolled out new firmware (currently 12.06.0065) and that issue was resolved. (SNMPWEBCARD is a component used in many of their products.) Unfortunately, now current plots as a flat line at 0. I’ve worked with Tripplite support to verify some data is present with snmpwalk. But probably not where Observium expects to find it. My guess is the firmware change switched to a new mib. I’ve tried to delete devices, update Observium and recreate… no luck. Tripplite currently provides these two MIBs http://www.tripplite.com/shared/software/Firmware/UPS-MIB-Definitions.txt http://www.tripplite.com/shared/software/Firmware/Tripp-Lite-MIB-Definition… Would be happy to switch to Professional, buy support, whatever is needed to restore ability to plot Current over time from Tripplite PDUMNH20. Any good advice? _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium%40observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium<http://postman.memetic.org/cgi-bin/mailman/listinfo/observium> _______________________________________________ observium mailing list observium(a)observium.org<mailto:observium@observium.org> http://postman.memetic.org/cgi-bin/mailman/listinfo/observium -- Mike Stupalov http://observium.org/

2 1

Tripplite PDUMNH20 (power strips)
by Ralph Pursifull 17 Oct '15

17 Oct '15

Hi. New to this list, so please excuse if I break etiquette. For couple years we happily used Observium to monitor and track current through our Tripplite PDUMNH20. Thanks to you all for Observium. Life was OK, but the integrated Tripplite SNMPWEBCARDs had problems from time to time. Tripplite rolled out new firmware (currently 12.06.0065) and that issue was resolved. (SNMPWEBCARD is a component used in many of their products.) Unfortunately, now current plots as a flat line at 0. I've worked with Tripplite support to verify some data is present with snmpwalk. But probably not where Observium expects to find it. My guess is the firmware change switched to a new mib. I've tried to delete devices, update Observium and recreate... no luck. Tripplite currently provides these two MIBs http://www.tripplite.com/shared/software/Firmware/UPS-MIB-Definitions.txt http://www.tripplite.com/shared/software/Firmware/Tripp-Lite-MIB-Definition… Would be happy to switch to Professional, buy support, whatever is needed to restore ability to plot Current over time from Tripplite PDUMNH20. Any good advice?

3 4

Add Bill to Normal User & Password Change for normal User
by Basile Bluntschli 16 Oct '15

16 Oct '15

Hi All 1) I no longer can add a bill to a normal user. While the dropdown menu is there, I can select the bill, but it does not get saved by clicking on ADD. 2) Where is a normal User able to change its password? URL? Running 7097 Thanks a lot Basile

3 3

Escaped sysContact not being escaped properly
by Spencer Ryan 16 Oct '15

16 Oct '15

I've got several UBNT devices all running EdgeMax 1.7.0 It appears that they escape the sysContact (and a few other fields) in quotes even if they don't have spaces in them. Observium seems to eat the first one properly but not the second. snmpwalk -Os -c public -v 2c router01 1.3.6.1.2.1.1.4 iso.3.6.1.2.1.1.4.0 = STRING: "\"hostmaster(a)arbor.net\"" However in the UI I see this: sysContact*=>*hostmaster(a)arbor.net\ Which causes email notifications to fail, because of the bad email address. Any hope? *Spencer Ryan* | Senior Systems Administrator | sryan(a)arbor.net *Arbor Networks* +1.734.794.5033 (d) | +1.734.846.2053 (m) www.arbornetworks.com

2 2

Ignore Statuses Possible?
by Tim Calvin 15 Oct '15

15 Oct '15

Hello We have a few AC powered Foundry FWS-24 switches. Observium is showing alerts for the secondary power supply and fans under statuses. Is there anyway to ignore these? I tried poking around and couldn’t find anything that would do the trick. I don’t even think they have secondary power supplies and fans. Maybe in another hardware configuration but certainly not ours. I have attached a screenshot. Running Observium Professional 0.15.10.7072

3 2

dlink DGS-1100-24 only found as generic
by Simon Smith 15 Oct '15

15 Oct '15

Hi All, our new D-Link DGS-1100-24 switches are only being discovered as generic device but strangely enough its finding 1 vlan? the syObjectID is being found as .1.3.6.1.4.1.171 but i can see inside os.inc.php the sysObjectID is already included as D-Link-Generic (Line:1950) even tho it could be put under the D-Link Switch (Line:1927) i have included a run poller.php and discover.php commands here - http://pastebin.com/8iKYU16N can the great and wonderful people working at Observium please help :-) Regards Simon - Hestor Ltd

2 3

Re: [Observium] Cannot see ospf or bgp info
by George Philip 15 Oct '15

15 Oct '15

Hi Adam,I am using Nexus 9k's and MX 480 with ospf and bgp. I am not sure why I don't any protocol related information on Observium. Thanks,George From: Adam Armstrong <adama(a)observium.org> To: George Philip <gkonapoz(a)yahoo.com> Sent: Wednesday, October 14, 2015 12:33 PM Subject: Re: [Observium] Cannot see ospf or bgp info Hi George,These features will only becomevisible in the ui once a device which supports them has been discovered andpolled.The devices need to supportbgp4-mib and ospf-mib.Thanks, Adam.Sent with AquaMail for Android http://www.aqua-mail.com On14 October 2015 4:11:30 pm George Philip <gkonapoz(a)yahoo.com> wrote: Hi,I installed Observium and have enabledthe bgp and ospf polling. However, I do not see the option of seeing thatinfo from the gui. I can see graphs on traffic but I cannot see any titlefor ospf or bgp. Also, I do not any entries for arp or mac table. Do I need to have license for thesefeatures ? Thanks, George_______________________________________________ observium mailing list observium(a)observium.org http://postman.memetic.org/cgi-bin/mailman/listinfo/observium

1 0

Cannot see ospf or bgp info
by George Philip 14 Oct '15

14 Oct '15

Hi,I installed Observium and have enabled the bgp and ospf polling. However, I do not see the option of seeing that info from the gui. I can see graphs on traffic but I cannot see any title for ospf or bgp. Also, I do not any entries for arp or mac table. Do I need to have license for these features ? Thanks, George

1 0

Obervium web page not coming up
by George Philip 14 Oct '15

14 Oct '15

Hi,I installed Observium on Centos and I added devices also successfully.Somehow, the webpage is not coming up and I followed the instruction mentioned in the webpage.My file /etc/http/conf/httpd.conf looks as follows: # <VirtualHost> definition. These values also provide defaults for # any <VirtualHost> containers you may define later in the file. # # All of these directives may appear inside <VirtualHost> containers, # in which case these default settings will be overridden for the # virtual host being defined. # # # ServerAdmin: Your address, where problems with the server should be # e-mailed. This address appears on some server-generated pages, such # as error documents. e.g. admin(a)your-domain.com # #ServerAdmin root@localhost # # ServerName gives the name and port that the server uses to identify itself. # This can often be determined automatically, but we recommend you specify # it explicitly to prevent problems during startup. # # If your host doesn't have a registered DNS name, enter its IP address here. # <VirtualHost *:80> DocumentRoot /opt/observium/html/ ServerName asvobs02.abcd.io CustomLog /opt/observium/logs/access_log combined ErrorLog /opt/observium/logs/error_log <Directory "/opt/observium/html/"> AllowOverride All Options FollowSymLinks MultiViews </Directory> </VirtualHost> Thanks, George

3 6